zarb-ml/mageia-dev/attachments/20130322/9d51da93/attachment.html


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41

<p dir="ltr"><br>
On 22 Mar 2013 22:21, &quot;Glen Ogilvie&quot; &lt;<a href="mailto:nelg@linuxsolutions.co.nz">nelg@linuxsolutions.co.nz</a>&gt; wrote:<br>
&gt;<br>
&gt; On 23 March 2013 05:12, AL13N &lt;<a href="mailto:alien@rmail.be">alien@rmail.be</a>&gt; wrote:<br>
&gt;&gt;<br>
&gt;&gt; Op vrijdag 22 maart 2013 07:38:56 schreef Frank Griffin:<br>
&gt;&gt; &gt; On 03/22/2013 07:20 AM, Glen Ogilvie wrote:<br>
&gt;&gt; [...]<br>
&gt;&gt; &gt; &gt; 1. How does the src tar.xz file for drakx-installer-stage2 get<br>
&gt;&gt; &gt; &gt; created?   I assume it comes from a<br>
&gt;&gt; &gt; &gt; build of svn://<a href="http://svn.mageia.org/svn/soft/drakx/trunk">svn.mageia.org/svn/soft/drakx/trunk</a><br>
&gt;&gt; &gt; &gt; &lt;<a href="http://svn.mageia.org/svn/soft/drakx/trunk">http://svn.mageia.org/svn/soft/drakx/trunk</a>&gt;, but can&#39;t find how it<br>
&gt;&gt; &gt; &gt; ends up as a tar.xz<br>
&gt;&gt; &gt;<br>
&gt;&gt; &gt; I&#39;m maybe about two days ahead of you on this, but here&#39;s what I think<br>
&gt;&gt; &gt; happens, FWIW.  You do your checkout, and then in the mdk-stage1<br>
&gt;&gt; &gt; subdirectory, do a &quot;make dist-svn&quot;.  This should produce the tar.xz in<br>
&gt;&gt; &gt; the mdk-stage1 directory.<br>
&gt;&gt; [...]<br>
&gt;&gt;<br>
&gt;&gt; &quot;make dist&quot; actually...<br>
&gt;&gt;<br>
&gt;&gt; it will target make &quot;dist-svn&quot; or &quot;make dist-git&quot; depending on if you&#39;re using<br>
&gt;&gt; git-svn or not.<br>
&gt;&gt;<br>
&gt;&gt; be advised that dist-svn uses the BASE and any uncommitted change will not be<br>
&gt;&gt; applied.<br>
&gt;&gt;<br>
&gt;&gt; dist-git however, you can commit without pushing them and that will be used.<br>
&gt;&gt;<br>
&gt;<br>
&gt; I&#39;ve had a good play around with make dist.<br>
&gt; It seems to me, like running make dist in the perl-install directory, (svn://<a href="http://svn.mageia.org/svn/soft/drakx/trunk/">svn.mageia.org/svn/soft/drakx/trunk/</a> )<br>
&gt; does not produce the same tar.xz file as found within drakx-installer-stage2 sources.<br>
&gt; For example, the tar.gz produced by &quot;make dist&quot; does not contain the &quot;kernel&quot;, &quot;perl-install/install&quot; directories, etc.<br>
&gt; Also, inside the tar, the first directory is: &quot;drakxtools-15.29&quot;, rather than &quot;drakx-installer-stage2-15.29&quot;.  It is also<br>
&gt; only 2.4MB instead of about 4.3MB.<br>
&gt;<br>
&gt; Any suggestions?</p>
<p dir="ltr">Yes, you need to go into install subdirectory (if I remember the name correctly)<br>
</p>