diff options
Diffstat (limited to 'sysconfig')
| -rwxr-xr-x | sysconfig/network-scripts/ifup-ipv6 | 22 | ||||
| -rw-r--r-- | sysconfig/network-scripts/network-functions-ipv6 | 9 |
2 files changed, 27 insertions, 4 deletions
diff --git a/sysconfig/network-scripts/ifup-ipv6 b/sysconfig/network-scripts/ifup-ipv6 index e8960553..45b1140a 100755 --- a/sysconfig/network-scripts/ifup-ipv6 +++ b/sysconfig/network-scripts/ifup-ipv6 @@ -11,7 +11,7 @@ # # RHL integration assistance by Pekka Savola <pekkas@netcore.fi> # -# Version 2002-11-02 +# Version 2002-11-12a # # Note: if called (like normally) by /etc/sysconfig/network-scripts/ifup # exit codes aren't handled by "ifup" @@ -35,6 +35,7 @@ # Optional for 6to4 tunneling (hardwired name of tunnel device is "tun6to4"): # IPV6TO4INIT=yes|no: controls 6to4 tunneling setup # IPV6TO4_RELAY=<IPv4 address>: IPv4 address of the remote 6to4 relay (default: 192.88.99.1) +# IPV6TO4_MTU=<MTU for IPv6>: controls IPv6 MTU for the 6to4 link (optional, default is MTU of interface - 20) # IPV6TO4_IPV4ADDR=<IPv4 address>: overwrite local IPv4 address (optional) # IPV6TO4_ROUTING="<device>-<suffix>/<prefix length> ...": information to setup local subnetting # Example: IPV6TO4_ROUTING="eth0-:f101::0/64 eth1-:f102::0/64" @@ -198,7 +199,22 @@ if [ "$IPV6TO4INIT" = "yes" ]; then # Setup 6to4 tunnel (hardwired name is "tun6to4"), if config is valid if [ "$valid6to4config" = "yes" ]; then - ipv6_add_6to4_tunnel tun6to4 $ipv4addr || exit 1 + # Get MTU of master device + ipv4mtu="`ipv6_exec_ip link show dev $DEVICE | grep -w "mtu" | awk '{ print $5 }'`" + if [ -n "$ipv4mtu" ]; then + # IPv6 tunnel MTU is IPv4 MTU minus 20 for IPv4 header + tunnelmtu=$[ $ipv4mtu - 20 ] + fi + + if [ -n "$IPV6TO4_MTU" ]; then + if [ $IPV6TO4_MTU -gt $tunnelmtu ]; then + echo $"Warning: configured MTU '$IPV6TO4_MTU' for 6to4 exceeds maximum limit of '$tunnelmtu', ignored" + else + tunnelmtu=$IPV6TO4_MTU + fi + fi + + ipv6_add_6to4_tunnel tun6to4 $ipv4addr "" $tunnelmtu || exit 1 # Add default route, if device matches if [ "$IPV6_DEFAULTDEV" = "tun6to4" ]; then @@ -217,7 +233,7 @@ if [ "$IPV6TO4INIT" = "yes" ]; then if [ -z "$gateway" ]; then gateway="$ipv6to4_relay" fi - ipv6_add_route $network $ipv6to4_relay tun6to4 + ipv6_add_route $network $gateway tun6to4 done fi diff --git a/sysconfig/network-scripts/network-functions-ipv6 b/sysconfig/network-scripts/network-functions-ipv6 index f6f83476..eba48121 100644 --- a/sysconfig/network-scripts/network-functions-ipv6 +++ b/sysconfig/network-scripts/network-functions-ipv6 @@ -5,7 +5,7 @@ # Taken from: network-functions-ipv6 # (P) & (C) 1997-2002 by Peter Bieringer <pb@bieringer.de> # -# Version: 2002-11-02 +# Version: 2002-11-12 # # Extended address detection is enabled, if 'ipv6calc' is installed # Available here: http://www.bieringer.de/linux/IPv6/ipv6calc/ @@ -1041,6 +1041,7 @@ ipv6_create_6to4_relay_address() { # $1: <Interface> : only "tun6to4" is supported # $2: <IPv4 address> : global address of local interface # $3: [<IPv6 suffix>] : for 6to4 prefix (optional, default is "::1") +# $4: [<MTU>] : MTU of tunnel device (optional, default is automatic) # return code: 0=ok 1=argument error 2=IPv6 test fails 3=major problem ipv6_add_6to4_tunnel() { local fn="ipv6_add_6to4_tunnel" @@ -1048,6 +1049,7 @@ ipv6_add_6to4_tunnel() { local device=$1 local localipv4=$2 local localipv6to4suffix=$3 + local mtu=$4 if [ -z "$device" ]; then ipv6_log $"Missing parameter 'device' (arg 1)" err $fn @@ -1086,6 +1088,11 @@ ipv6_add_6to4_tunnel() { local retval=0 fi + # Set MTU, if given + if [ -n "$mtu" ]; then + ipv6_set_mtu $device $mtu + fi + return $retval } |