diff options
Diffstat (limited to 'perl-install/help.pm')
| -rw-r--r-- | perl-install/help.pm | 671 |
1 files changed, 0 insertions, 671 deletions
diff --git a/perl-install/help.pm b/perl-install/help.pm deleted file mode 100644 index 6a17e6c1d..000000000 --- a/perl-install/help.pm +++ /dev/null @@ -1,671 +0,0 @@ -package help; - -use common qw(:common); - -%steps = ( -selectLanguage => -__("Choose preferred language for install and system usage."), - -selectKeyboard => - __("Choose the layout corresponding to your keyboard from the list above"), - -selectInstallClass => - __("Choose \"Install\" if there are no previous versions of Linux -installed, or if you wish to use multiple distributions or versions. - -Choose \"Upgrade\" if you wish to update a previous version of Mandrake Linux: -5.1 (Venice), 5.2 (Leloo), 5.3 (Festen), 6.0 (Venus), 6.1 (Helios), Gold 2000 -or 7.0 (Air). - - -Select: - - - Automated (recommended): If you have never installed Linux before, choose this. NOTE: - networking will not be configured during installation, use \"LinuxConf\" - to configure it after the install completes. - - - Customized: If you are familiar enough with GNU/Linux, you may then choose - the primary usage for your machine. See below for details. - - - Expert: This supposes that you are fluent with GNU/Linux and want to - perform a highly customized installation. As for a \"Customized\" - installation class, you will be able to select the usage for your system. - But please, please, DO NOT CHOOSE THIS UNLESS YOU KNOW WHAT YOU ARE DOING! -"), - -selectInstallClassCorpo => - __("Select: - - - Customized: If you are familiar enough with GNU/Linux, you may then choose - the primary usage for your machine. See below for details. - - - Expert: This supposes that you are fluent with GNU/Linux and want to - perform a highly customized installation. As for a \"Customized\" - installation class, you will be able to select the usage for your system. - But please, please, DO NOT CHOOSE THIS UNLESS YOU KNOW WHAT YOU ARE DOING! -"), - -selectInstallClass2 => -__("The different choices for your machine's usage (provided, hence, that you have -chosen either \"Custom\" or \"Expert\" as an installation class) are the -following: - - - Normal: choose this if you intend to use your machine primarily for - everyday use (office work, graphics manipulation and so on). Do not - expect any compiler, development utility et al. installed. - - - Development: as its name says. Choose this if you intend to use your - machine primarily for software development. You will then have a complete - collection of software installed in order to compile, debug and format - source code, or create software packages. - - - Server: choose this if the machine which you're installing Linux-Mandrake - on is intended to be used as a server. Either a file server (NFS or SMB), - a print server (Unix' lp (Line Printer) protocol or Windows style SMB - printing), an authentication server (NIS), a database server and so on. As - such, do not expect any gimmicks (KDE, GNOME...) to be installed. -"), - -setupSCSI => - __("DrakX will attempt at first to look for one or more PCI -SCSI adapter(s). If it finds it (or them) and knows which driver(s) -to use, it will insert it (them) automatically. - - -If your SCSI adapter is an ISA board, or is a PCI board but DrakX -doesn't know which driver to use for this card, or if you have no -SCSI adapters at all, you will then be prompted on whether you have -one or not. If you have none, answer \"No\". If you have one or more, -answer \"Yes\". A list of drivers will then pop up, from which you -will have to select one. - - -After you have selected the driver, DrakX will ask if you -want to specify options for it. First, try and let the driver -probe for the hardware: it usually works fine. - - -If not, do not forget the information on your hardware that you -could get from your documentation or from Windows (if you have it -on your system), as suggested by the installation guide. These -are the options you will need to provide to the driver."), - -partitionDisks => - __("At this point, you may choose what partition(s) to use to install -your Linux-Mandrake system if they have been already defined (from a -previous install of Linux or from another partitionning tool). In other -cases, hard drive partitions must be defined. This operation consists of -logically dividing the computer's hard drive capacity into separate -areas for use. - - -If you have to create new partitions, use \"Auto allocate\" to automatically -create partitions for Linux. You can select the disk for partitionning by -clicking on \"hda\" for the first IDE drive, -\"hdb\" for the second or \"sda\" for the first SCSI drive and so on. - - -Two common partition are: the root partition (/), which is the starting -point of the filesystem's directory hierarchy, and /boot, which contains -all files necessary to start the operating system when the -computer is first turned on. - - -Because the effects of this process are usually irreversible, partitioning -can be intimidating and stressful to the unexperienced user. DiskDrake -simplifies the process so that it must not be. Consult the documentation -and take your time before proceeding. - - -You can reach any option using the keyboard: navigate through the partitions -using Tab and Up/Down arrows. When a partition is selected, you can use: - -- Ctrl-c to create a new partition (when an empty partition is selected) - -- Ctrl-d to delete a partition - -- Ctrl-m to set the mount point -"), - -formatPartitions => - __("Any partitions that have been newly defined must be formatted for -use (formatting meaning creating a filesystem). At this time, you may -wish to re-format some already existing partitions to erase the data -they contain. Note: it is not necessary to re-format pre-existing -partitions, particularly if they contain files or data you wish to keep. -Typically retained are /home and /usr/local."), - -choosePackages => - __("You may now select the group of packages you wish to -install or upgrade. - -DrakX will then check whether you have enough room to install them all. If not, -it will warn you about it. If you want to go on anyway, it will proceed onto -the installation of all selected groups but will drop some packages of lesser -interest. At the bottom of the list you can select the option -\"Individual package selection\"; in this case you will have to browse -through more than 1000 packages..."), - -chooseCD => - __("If you have all the CDs in the list above, click Ok. -If you have none of those CDs, click Cancel. -If only some CDs are missing, unselect them, then click Ok."), - -doInstallStep => - __("The packages selected are now being installed. This operation -should take a few minutes unless you have chosen to upgrade an -existing system, in that case it can take more time even before -upgrade starts."), - -selectMouse => - __("If DrakX failed to find your mouse, or if you want to -check what it has done, you will be presented the list of mice -above. - - -If you agree with DrakX' settings, just jump to the section -you want by clicking on it in the menu on the left. Otherwise, -choose a mouse type in the menu which you think is the closest -match for your mouse. - - -In case of a serial mouse, you will also have to tell DrakX -which serial port it is connected to."), - -selectSerialPort => - __("Please select the correct port. For example, the COM1 port under MS Windows -is named ttyS0 under Linux."), - -configureNetwork => - __("This section is dedicated to configuring a local area -network (LAN) or a modem. - -Choose \"Local LAN\" and DrakX will -try to find an Ethernet adapter on your machine. PCI adapters -should be found and initialized automatically. -However, if your peripheral is ISA, autodetection will not work, -and you will have to choose a driver from the list that will appear then. - - -As for SCSI adapters, you can let the driver probe for the adapter -in the first time, otherwise you will have to specify the options -to the driver that you will have fetched from documentation of your -hardware. - - -If you install a Linux-Mandrake system on a machine which is part -of an already existing network, the network administrator will -have given you all necessary information (IP address, network -submask or netmask for short, and hostname). If you're setting -up a private network at home for example, you should choose -addresses. - - -Choose \"Dialup with modem\" and the Internet connection with -a modem will be configured. DrakX will try to find your modem, -if it fails you will have to select the right serial port where -your modem is connected to."), - -configureNetworkIP => - __("Enter: - - - IP address: if you don't know it, ask your network administrator or ISP. - - - - Netmask: \"255.255.255.0\" is generally a good choice. If you are not -sure, ask your network administrator or ISP. - - - - Automatic IP: If your network uses bootp or dhcp protocol, select -this option. If selected, no value is needed in \"IP address\". If you are -not sure, ask your network administrator or ISP. -"), - -configureNetworkISP => - __("You may now enter dialup options. If you're not sure what to enter, the -correct information can be obtained from your ISP."), - -configureNetworkProxy => - __("If you will use proxies, please configure them now. If you don't know if -you should use proxies, ask your network administrator or your ISP."), - -installCrypto => - __("You can install cryptographic package if your internet connection has been -set up correctly. First choose a mirror where you wish to download packages and -after that select the packages to install. - -Note you have to select mirror and cryptographic packages according -to your legislation."), - -configureTimezone => - __("You can now select your timezone according to where you live. - - -Linux manages time in GMT or \"Greenwich Mean Time\" and translates it -in local time according to the time zone you have selected."), - -configureServices => - __("You may now choose which services you want to see started at boot time. -When your mouse comes over an item, a small balloon help will popup which -describes the role of the service. - -Be especially careful in this step if you intend to use your machine as a -server: you will probably want not to start any services which you don't -want."), - -configurePrinter => - __("Linux can deal with many types of printer. Each of these -types require a different setup. Note however that the print -spooler uses 'lp' as the default printer name; so you -must have one printer with such a name; but you can give -several names, separated by '|' characters, to a printer. -So, if you prefer to have a more meaningful name you just have -to put it first, eg: \"My Printer|lp\". -The printer having \"lp\" in its name(s) will be the default printer. - - -If your printer is physically connected to your computer, select -\"Local printer\". You will then have to tell which port your -printer is connected to, and select the appropriate filter. - - -If you want to access a printer located on a remote Unix machine, -you will have to select \"Remote lpd\". In order to make -it work, no username or password is required, but you will need -to know the name of the printing queue on this server. - - -If you want to access a SMB printer (which means, a printer located -on a remote Windows 9x/NT machine), you will have to specify its -SMB name (which is not its TCP/IP name), and possibly its IP address, -plus the username, workgroup and password required in order to -access the printer, and of course the name of the printer. The same goes -for a NetWare printer, except that you need no workgroup information."), - -setRootPassword => - __("You can now enter the root password for your Linux-Mandrake -system. The password must be entered twice to verify that both -password entries are identical. - - -Root is the administrator of the system, and is the only user -allowed to modify the system configuration. Therefore, choose -this password carefully! Unauthorized use of the root account can -be extremely dangerous to the integrity of the system and its data, -and other systems connected to it. The password should be a -mixture of alphanumeric characters and a least 8 characters long. It -should NEVER be written down. Do not make the password too long or -complicated, though: you must be able to remember without too much -effort."), - -setRootPasswordMd5 => - __("To enable a more secure system, you should select \"Use shadow file\" and -\"Use MD5 passwords\"."), - -setRootPasswordNIS => - __("If your network uses NIS, select \"Use NIS\". If you don't know, ask your -network administrator."), - -addUser => - __("You may now create one or more \"regular\" user account(s), as -opposed to the \"privileged\" user account, root. You can create -one or more account(s) for each person you want to allow to use -the computer. Note that each user account will have its own -preferences (graphical environment, program settings, etc.) -and its own \"home directory\", in which these preferences are -stored. - - -First of all, create an account for yourself! Even if you will be the only user -of the machine, you may NOT connect as root for daily use of the system: it's a -very high security risk. Making the system unusable is very often a typo away. - - -Therefore, you should connect to the system using the user account -you will have created here, and login as root only for administration -and maintenance purposes."), - -createBootdisk => - __("It is strongly recommended that you answer \"Yes\" here. If you install -Microsoft Windows at a later date it will overwrite the boot sector. -Unless you have made a bootdisk as suggested, you will not be able to -boot into Linux any more."), - -setupBootloaderBeginner => - __("You need to indicate where you wish -to place the information required to boot to Linux. - - -Unless you know exactly what you are doing, choose \"First sector of -drive (MBR)\"."), - -setupBootloader => - __("Unless you know specifically otherwise, the usual choice is \"/dev/hda\" - (primary master IDE disk) or \"/dev/sda\" (first SCSI disk)."), - -setupBootloaderAddEntry => - __("LILO (the LInux LOader) and Grub are bootloaders: they are able to boot -either Linux or any other operating system present on your computer. -Normally, these other operating systems are correctly detected and -installed. If this is not the case, you can add an entry by hand in this -screen. Be careful as to choose the correct parameters. - - -You may also want not to give access to these other operating systems to -anyone, in which case you can delete the corresponding entries. But -in this case, you will need a boot disk in order to boot them!"), - -setupBootloaderGeneral => - __("LILO and grub main options are: - - Boot device: Sets the name of the device (e.g. a hard disk -partition) that contains the boot sector. Unless you know specifically -otherwise, choose \"/dev/hda\". - - - - Delay before booting default image: Specifies the number in tenths -of a second the boot loader should wait before booting the first image. -This is useful on systems that immediately boot from the hard disk after -enabling the keyboard. The boot loader doesn't wait if \"delay\" is -omitted or is set to zero. - - - - Video mode: This specifies the VGA text mode that should be selected -when booting. The following values are available: - * normal: select normal 80x25 text mode. - * <number>: use the corresponding text mode."), - -configureX => - __("Now it's time to configure the X Window System, which is the -core of the Linux GUI (Graphical User Interface). For this purpose, -you must configure your video card and monitor. Most of these -steps are automated, though, therefore your work may only consist -of verifying what has been done and accept the settings :) - - -When the configuration is over, X will be started (unless you -ask DrakX not to) so that you can check and see if the -settings suit you. If they don't, you can come back and -change them, as many times as necessary."), - -configureXmain => - __("If something is wrong in X configuration, use these options to correctly -configure the X Window System."), - -configureXxdm => - __("If you prefer to use a graphical login, select \"Yes\". Otherwise, select -\"No\"."), - -miscellaneous => - __("You can now select some miscellaneous options for your system. - - - Use hard drive optimizations: this option can improve hard disk performance - but is only for advanced users: some buggy chipsets can ruin your data, so - beware. Note that the kernel has a builtin blacklist of drives and - chipsets, but if you want to avoid bad surprises, leave this option unset. - - - Choose security level: you can choose a security level for your - system. Please refer to the manual for complete information. Basically: if - you don't know, select \"Medium\" ; if you really want to have a secure - machine, choose \"Paranoid\" but beware: IN THIS LEVEL, ROOT LOGIN AT - CONSOLE IS NOT ALLOWED! If you want to be root, you have to login as a user - and then use \"su\". More generally, do not expect to use your machine - for anything but as a server. You have been warned. - - - Precise RAM size if needed: unfortunately, in today's PC world, there is no - standard method to ask the BIOS about the amount of RAM present in your - computer. As a consequence, Linux may fail to detect your amount of RAM - correctly. If this is the case, you can specify the correct amount of RAM - here. Note that a difference of 2 or 4 MB is normal. - - - Removable media automounting: if you would prefer not to manually - mount removable media (CD-ROM, Floppy, Zip) by typing \"mount\" and - \"umount\", select this option. - - - Enable NumLock at startup: if you want NumLock enabled after booting, - select this option (Note: NumLock may or may not work under X)."), - -exitInstall => - __("Your system is going to reboot. - -After rebooting, your new Linux Mandrake system will load automatically. -If you want to boot into another existing operating system, please read -the additional instructions."), -); - -#-#- ################################################################################ -#-#- NO LONGER UP-TO-DATE... -#-%steps_long = ( -#-selectLanguage => -#- __("Choose preferred language for install and system usage."), -#- -#-selectKeyboard => -#- __("Choose the layout corresponding to your keyboard from the list above"), -#- -#-selectPath => -#- __("Choose \"Installation\" if there are no previous versions of Linux -#-installed, or if you wish to use multiple distributions or versions. -#- -#- -#-Choose \"Update\" if you wish to update a previous version of Mandrake -#-Linux: 5.1 (Venice), 5.2 (Leeloo), 5.3 (Festen) or 6.0 (Venus)."), -#- -#-selectInstallClass => -#- __("Select: -#- -#- - Beginner: If you have never installed Linux before, and wish to -#-install the distribution elected \"Product of the year\" for 1999, -#-click here. -#- -#- - Developer: If you are familiar with Linux and will be using the -#-computer primarily for software development, you will find happiness -#-here. -#- -#- - Server: If you wish to install a general purpose server, or the -#-Linux distribution elected \"Distribution/Server\" for 1999, select -#-this. -#- -#- - Expert: If you are fluent with GNU/Linux and want to perform -#-a highly customized installation, this Install Class is for you."), -#- -#-setupSCSI => -#- __("DrakX will attempt at first to look for one or more PCI -#-SCSI adapter(s). If it finds it (or them) and knows which driver(s) -#-to use, it will insert it (them) automatically. -#- -#-If your SCSI adapter is ISA, or is PCI but DrakX doesn't know -#-which driver to use for this card, or if you have no SCSI adapters -#-at all, you will then be prompted on whether you have one or not. -#-If you have none, answer \"No\". If you have one or more, answer -#-\"Yes\". A list of drivers will then pop up, from which you will -#-have to select one. -#- -#-After you have selected the driver, DrakX will ask if you -#-want to specify options for it. First, try and let the driver -#-probe for the hardware: it usually works fine. -#- -#-If not, do not forget the information on your hardware that you -#-could get from you documentation or from Windows (if you have -#-it on your system), as suggested by the installation guide. -#-These are the options you will need to provide to the driver."), -#- -#-partitionDisks => -#- __("In this stage, you may choose what partition(s) use to install your -#-Linux-Mandrake system."), -#- -#-#At this point, hard drive partitions must be defined. (Unless you -#-#are overwriting a previous install of Linux and have already defined -#-#your hard drive partitions as desired.) This operation consists of -#-#logically dividing the computer's hard drive capacity into separate -#-#areas for use. -#-# -#-# -#-#Two common partition are: the root partition (/), which is the starting -#-#point of the filesystem's directory hierarchy, and /boot, which contains -#-#all files necessary to start the operating system when the -#-#computer is first turned on. -#-# -#-# -#-#Because the effects of this process are usually irreversible, partitioning -#-#can be intimidating and stressful to the unexperienced. DiskDrake -#-#simplifies the process so that it need not be. Consult the documentation -#-#and take your time before proceeding."), -#- -#-formatPartitions => -#- __("Any partitions that have been newly defined must be formatted for -#-use (formatting meaning creating a filesystem). At this time, you may -#-wish to re-format some already existing partitions to erase the data -#-they contain. Note: it is not necessary to re-format pre-existing -#-partitions, particularly if they contain files or data you wish to keep. -#-Typically retained are /home and /usr/local."), -#- -#-choosePackages => -#- __("You may now select the packages you wish to install. -#- -#- -#-Please note that some packages require the installation of others. -#-These are referred to as package dependencies. The packages you select, -#-and the packages they require will be automatically selected for -#-install. It is impossible to install a package without installing all -#-of its dependencies. -#- -#- -#-Information on each category and specific package is available in the -#-area titled \"Info\", located between list of packages and the five -#-buttons \"Install\", \"Select more/less\" and \"Show more/less\"."), -#- -#-doInstallStep => -#- __("The packages selected are now being installed. -#- -#- -#-This operation should take a few minutes."), -#- -#-selectMouse => -#- __("If DrakX failed to find your mouse, or if you want to -#-check what it has done, you will be presented the list of mice -#-above. -#- -#- -#-If you agree with DrakX' settings, just jump to the section -#-you want by clicking on it in the menu on the left. Otherwise, -#-choose a mouse type in the menu which you think is the closest -#-match for your mouse. -#- -#-In case of a serial mouse, you will also have to tell DrakX -#-which serial port it is connected to."), -#- -#-configureNetwork => -#- __("This section is dedicated to configuring a local area network, -#-or LAN. If you answer \"Yes\" here, DrakX will try to find an -#-Ethernet adapter on your machine. PCI adapters should be found and -#-initialized automatically. However, if your peripheral is ISA, -#-autodetection will not work, and you will have to choose a driver -#-from the list that will appear then. -#- -#- -#-As for SCSI adapters, you can let the driver probe for the adapter -#-in the first time, otherwise you will have to specify the options -#-to the driver that you will have fetched from Windows' control -#-panel. -#- -#- -#-If you install a Linux-Mandrake system on a machine which is part -#-of an already existing network, the network administrator will -#-have given you all necessary information (IP address, network -#-submask or netmask for short, and hostname). If you're setting -#-up a private network at home for example, you should choose -#-addresses "), -#- -#-configureTimezone => -#- __("Help"), -#- -#-configureServices => -#- __("Help"), -#- -#-configurePrinter => -#- __("Linux can deal with many types of printer. Each of these -#-types require a different setup. -#- -#- -#-If your printer is directly connected to your computer, select -#-\"Local printer\". You will then have to tell which port your -#-printer is connected to, and select the appropriate filter. -#- -#- -#-If you want to access a printer located on a remote Unix machine, -#-you will have to select \"Remote lpd queue\". In order to make -#-it work, no username or password is required, but you will need -#-to know the name of the printing queue on this server. -#- -#- -#-If you want to access a SMB printer (which means, a printer located -#-on a remote Windows 9x/NT machine), you will have to specify its -#-SMB name (which is not its TCP/IP name), and possibly its IP address, -#-plus the username, workgroup and password required in order to -#-access the printer, and of course the name of the printer.The same goes -#-for a NetWare printer, except that you need no workgroup information."), -#- -#-setRootPassword => -#- __("You must now enter the root password for your Linux-Mandrake -#-system. The password must be entered twice to verify that both -#-password entries are identical. -#- -#- -#-Root is the administrator of the system, and is the only user -#-allowed to modify the system configuration. Therefore, choose -#-this password carefully! Unauthorized use of the root account can -#-be extremely dangerous to the integrity of the system and its data, -#-and other systems connected to it. The password should be a -#-mixture of alphanumeric characters and a least 8 characters long. It -#-should *never* be written down. Do not make the password too long or -#-complicated, though: you must be able to remember without too much -#-effort."), -#- -#-addUser => -#- __("You may now create one or more \"regular\" user account(s), as -#-opposed to the \"privileged\" user account, root. You can create -#-one or more account(s) for each person you want to allow to use -#-the computer. Note that each user account will have its own -#-preferences (graphical environment, program settings, etc.) -#-and its own \"home directory\", in which these preferences are -#-stored. -#- -#- -#-First of all, create an account for yourself! Even if you will be the only user -#-of the machine, you may NOT connect as root for daily use of the system: it's a -#-very high security risk. Making the system unusable is very often a typo away. -#- -#- -#-Therefore, you should connect to the system using the user account -#-you will have created here, and login as root only for administration -#-and maintenance purposes."), -#- -#-createBootdisk => -#- __("Please, please, answer \"Yes\" here! Just for example, when you -#-reinstall Windows, it will overwrite the boot sector. Unless you have -#-made the bootdisk as suggested, you won't be able to boot into Linux -#-any more!"), -#- -#-setupBootloader => -#- __("You need to indicate where you wish -#-to place the information required to boot to Linux. -#- -#- -#-Unless you know exactly what you are doing, choose \"First sector of -#-drive (MBR)\"."), -#- -#-configureX => -#- __("Now it's time to configure the X Window System, which is the -#-core of the Linux GUI (Graphical User Interface). For this purpose, -#-you must configure your video card and monitor. Most of these -#-steps are automated, though, therefore your work may only consist -#-of verifying what has been done and accept the settings :) -#- -#- -#-When the configuration is over, X will be started (unless you -#-ask DrakX not to) so that you can check and see if the -#-settings suit you. If they don't, you can come back and -#-change them, as many times as necessary."), -#- -#-exitInstall => -#- __("Help"), -#-); |