diff options
Diffstat (limited to 'mdk-stage1/rp-pppoe/scripts/adsl-start.in')
| -rwxr-xr-x | mdk-stage1/rp-pppoe/scripts/adsl-start.in | 186 |
1 files changed, 0 insertions, 186 deletions
diff --git a/mdk-stage1/rp-pppoe/scripts/adsl-start.in b/mdk-stage1/rp-pppoe/scripts/adsl-start.in deleted file mode 100755 index 33251a851..000000000 --- a/mdk-stage1/rp-pppoe/scripts/adsl-start.in +++ /dev/null @@ -1,186 +0,0 @@ -#!/bin/sh -# @configure_input@ -#*********************************************************************** -# -# adsl-start -# -# Shell script to bring up an ADSL connection -# -# Copyright (C) 2000 Roaring Penguin Software Inc. -# -# $Id$ -# -# This file may be distributed under the terms of the GNU General -# Public License. -# -# Usage: adsl-start [config_file] -# adsl-start interface user [config_file] -# Second form overrides USER and ETH from config file. -# If config_file is omitted, defaults to /etc/ppp/pppoe.conf -# -#*********************************************************************** - -# From AUTOCONF -prefix=@prefix@ -exec_prefix=@exec_prefix@ - -# Paths to programs -CONNECT=@sbindir@/adsl-connect -ECHO=@ECHO@ -IFCONFIG=/sbin/ifconfig - -# Defaults -CONFIG=/etc/ppp/pppoe.conf -USER="" -ETH="" -ME=`basename $0` -# Must be root -if [ "`@ID@ -u`" != 0 ] ; then - $ECHO "$ME: You must be root to run this script" >& 2 - exit 1 -fi - -# Debugging -if [ "$DEBUG" = "1" ] ; then - $ECHO "*** Running in debug mode... please be patient..." - DEBUG=/tmp/pppoe-debug-$$ - export DEBUG - mkdir $DEBUG - if [ "$?" != 0 ] ; then - $ECHO "Could not create directory $DEBUG... exiting" - exit 1 - fi - DEBUG=$DEBUG/pppoe-debug.txt - - # Initial debug output - $ECHO "---------------------------------------------" > $DEBUG - $ECHO "* The following section contains information about your system" >> $DEBUG - date >> $DEBUG - $ECHO "Output of uname -a" >> $DEBUG - uname -a >> $DEBUG - $ECHO "---------------------------------------------" >> $DEBUG - $ECHO "* The following section contains information about your network" >> $DEBUG - $ECHO "* interfaces. The one you chose for PPPoE should contain the words:" >> $DEBUG - $ECHO "* 'UP' and 'RUNNING'. If it does not, you probably have an Ethernet" >> $DEBUG - $ECHO "* driver problem." >> $DEBUG - $ECHO "Output of ifconfig -a" >> $DEBUG - $IFCONFIG -a >> $DEBUG - $ECHO "---------------------------------------------" >> $DEBUG - if [ "`uname -s`" = "Linux" ] ; then - $ECHO "* The following section contains information about kernel modules" >> $DEBUG - $ECHO "* If the module for your Ethernet card is 'tulip', you might" >> $DEBUG - $ECHO "* want to look for an updated version at http://www.scyld.com" >> $DEBUG - $ECHO "Output of lsmod" >> $DEBUG - lsmod >> $DEBUG - $ECHO "---------------------------------------------" >> $DEBUG - fi - $ECHO "* The following section lists your routing table." >> $DEBUG - $ECHO "* If you have an entry which starts with '0.0.0.0', you probably" >> $DEBUG - $ECHO "* have defined a default route and gateway, and pppd will" >> $DEBUG - $ECHO "* not create a default route using your ISP. Try getting" >> $DEBUG - $ECHO "* rid of this route." >> $DEBUG - $ECHO "Output of netstat -n -r" >> $DEBUG - netstat -n -r >> $DEBUG - $ECHO "---------------------------------------------" >> $DEBUG - $ECHO "Contents of /etc/resolv.conf" >> $DEBUG - $ECHO "* The following section lists DNS setup." >> $DEBUG - $ECHO "* If you can browse by IP address, but not name, suspect" >> $DEBUG - $ECHO "* a DNS problem." >> $DEBUG - cat /etc/resolv.conf >> $DEBUG - $ECHO "---------------------------------------------" >> $DEBUG - $ECHO "* The following section lists /etc/ppp/options." >> $DEBUG - $ECHO "* You should have NOTHING in that file." >> $DEBUG - $ECHO "Contents of /etc/ppp/options" >> $DEBUG - cat /etc/ppp/options >> $DEBUG 2>/dev/null - $ECHO "---------------------------------------------" >> $DEBUG -else - DEBUG="" -fi - -# Sort out command-line arguments -case "$#" in - 1) - CONFIG="$1" - ;; - 3) - CONFIG="$3" - ;; -esac - -if [ ! -f "$CONFIG" -o ! -r "$CONFIG" ] ; then - $ECHO "$ME: Cannot read configuration file '$CONFIG'" >& 2 - exit 1 -fi - -. $CONFIG - -# Check for command-line overriding of ETH and USER -case "$#" in - 2|3) - ETH="$1" - USER="$2" - ;; -esac - -# Check for pidfile -if [ -r "$PIDFILE" ] ; then - PID=`cat "$PIDFILE"` - # Check if still running - kill -0 $PID > /dev/null 2>&1 - if [ $? = 0 ] ; then - $ECHO "$ME: There already seems to be an ADSL connection up (PID $PID)" >& 2 - exit 1 - fi - # Delete bogus PIDFILE - rm -f "$PIDFILE" "$PIDFILE.pppd" "$PIDFILE.pppoe" "$PIDFILE.start" -fi - -echo $$ > $PIDFILE.start - -# Start the connection in the background unless we're debugging -if [ "$DEBUG" != "" ] ; then - $CONNECT "$@" - exit 0 -fi - -$CONNECT "$@" > /dev/null 2>&1 & -CONNECT_PID=$! - -if [ "$CONNECT_TIMEOUT" = "" -o "$CONNECT_TIMEOUT" = 0 ] ; then - exit 0 -fi - -# Don't monitor connection if dial-on-demand -if [ "$DEMAND" != "" -a "$DEMAND" != "no" ] ; then - exit 0 -fi - -# Monitor connection -TIME=0 -while [ true ] ; do - @sbindir@/adsl-status $CONFIG > /dev/null 2>&1 - - # Looks like the interface came up - if [ $? = 0 ] ; then - # Print newline if standard input is a TTY - tty -s && $ECHO " Connected!" - exit 0 - fi - - if test -n "$FORCEPING" ; then - $ECHO -n "$FORCEPING" - else - tty -s && $ECHO -n "$PING" - fi - sleep $CONNECT_POLL - TIME=`expr $TIME + $CONNECT_POLL` - if [ $TIME -gt $CONNECT_TIMEOUT ] ; then - break - fi -done - -$ECHO "TIMED OUT" >& 2 -# Timed out! Kill the adsl-connect process and quit -kill $CONNECT_PID > /dev/null 2>&1 -exit 1 - |