diff options
Diffstat (limited to 'perl-install/Xconfigurator_consts.pm')
| -rw-r--r-- | perl-install/Xconfigurator_consts.pm | 666 |
1 files changed, 453 insertions, 213 deletions
diff --git a/perl-install/Xconfigurator_consts.pm b/perl-install/Xconfigurator_consts.pm index 976f65d9e..ebe6ba6b9 100644 --- a/perl-install/Xconfigurator_consts.pm +++ b/perl-install/Xconfigurator_consts.pm @@ -1,208 +1,378 @@ +package Xconfigurator; # $Id$ + use common qw(:common); -%keymap_translate = ( - uk => "gb", +%depths = ( + 8 => __("256 colors (8 bits)"), + 15 => __("32 thousand colors (15 bits)"), + 16 => __("65 thousand colors (16 bits)"), + 24 => __("16 million colors (24 bits)"), + 32 => __("4 billion colors (32 bits)"), ); +@depths = ikeys(%depths); -@depths = qw(8 15 16 24 32); - -$resolution_wanted = "1024x768"; @resolutions = qw(640x480 800x600 1024x768 1152x864 1280x1024 1600x1200); +@window_managers = ('kdeinit: kwin', qw(gnome-session icewm wmaker kwm afterstep fvwm fvwm2 fvwm95 mwm twm enlightenment xfce blackbox sawfish)); + +%serversdriver = arch() =~ /^sparc/ ? ( + 'Mach64' => "accel", + '3DLabs' => "accel", + 'Sun' => "fbdev", + 'Sun24' => "fbdev", + 'SunMono' => "fbdev", + 'VGA16' => "vga16", + 'FBDev' => "fbdev", +) : ( + 'SVGA' => "svga", +#- 'Rage128' => "svga", +#- '3dfx' => "svga", + 'S3' => "accel", + 'Mach32' => "accel", + 'Mach8' => "accel", + '8514' => "accel", + 'P9000' => "accel", + 'AGX' => "accel", + 'W32' => "accel", + 'Mach64' => "accel", + 'I128' => "accel", + 'S3V' => "accel", + '3DLabs' => "accel", + 'Mono' => "vga2", + 'VGA16' => "vga16", + 'FBDev' => "fbdev", +); +@svgaservers = grep { $serversdriver{$_} eq "svga" } keys(%serversdriver); +@accelservers = grep { $serversdriver{$_} eq "accel" } keys(%serversdriver); +@allbutfbservers = grep { arch() =~ /^sparc/ || $serversdriver{$_} ne "fbdev" } keys(%serversdriver); +@allservers = keys(%serversdriver); + +%vgamodes = ( + '640xx8' => 769, + '640x480x8' => 769, + '800xx8' => 771, + '800x600x8' => 771, + '1024xx8' => 773, + '1024x768x8' => 773, + '1280xx8' => 775, + '1280x1024x8' => 775, + '640xx15' => 784, + '640x480x15' => 784, + '800xx15' => 787, + '800x600x15' => 787, + '1024xx15' => 790, + '1024x768x15' => 790, + '1280xx15' => 793, + '1280x1024x15' => 793, + '640xx16' => 785, + '640x480x16' => 785, + '800xx16' => 788, + '800x600x16' => 788, + '1024xx16' => 791, + '1024x768x16' => 791, + '1280xx16' => 794, + '1280x1024x16' => 794, +#- '640xx24' => 786, #- there is a problem with these resolutions since the BIOS may take 24 or 32 planes. +#- '640x480x24' => 786, +#- '800xx24' => 789, +#- '800x600x24' => 789, +#- '1024xx24' => 792, +#- '1024x768x24' => 792, +#- '1280xx24' => 795, +#- '1280x1024x24' => 795, +); -@accelservers = qw(S3 Mach32 Mach8 8514 P9000 AGX W32 Mach64 I128 S3V 3DLabs); -@allservers = (qw(Mono VGA16 SVGA), @accelservers); +{ #- @monitorSize2resolution + my %l = my @l = ( #- size in inch + 13 => "640x480", + 14 => "800x600", + 15 => "800x600", + 16 => "1024x768", + 17 => "1024x768", + 18 => "1024x768", + 19 => "1280x1024", + 20 => "1280x1024", + 21 => "1600x1200", + ); + for (my $i = 0; $i < $l[0]; $i++) { + $monitorSize2resolution[$i] = $l[1]; + } + while (my ($s, $r) = each %l) { + $monitorSize2resolution[$s] = $r; + } +} %videomemory = ( - __("256 kb") => 256, - __("512 kb") => 512, - __("1 mb") => 1024, - __("2 mb") => 2048, - __("4 mb") => 4096, - __("8 mb") => 8192, - __("16 mb or more") => 16384, + __("256 kB") => 256, + __("512 kB") => 512, + __("1 MB") => 1024, + __("2 MB") => 2048, + __("4 MB") => 4096, + __("8 MB") => 8192, + __("16 MB or more") => 16384, ); +$default_monitor = "High Frequency SVGA, 1024x768 at 70 Hz"; %standard_monitors = ( - __("Standard VGA, 640x480 in 60 Hz") => [ '640x480@60', "31.5" , "60" ], - __("Super VGA, 800x600 in 56 Hz") => [ '800x600@56', "31.5-35.1" , "55-60" ], - __("8514 Compatible, 1024x768 in 87 Hz interlaced (no 800x600)") => [ '8514 compatible', "31.5,35.5" , "60,70,87" ], - __("Super VGA, 1024x768 in 87 Hz interlaced, 800x600 in 56 Hz") => [ '1024x768@87i', "31.5,35.15,35.5" , "55-90" ], - __("Extended Super VGA, 800x600 in 60 Hz, 640x480 in 72 Hz") => [ '800x600@60', "31.5-37.9" , "55-90" ], - __("Non-Interlaced SVGA, 1024x768 in 60 Hz, 800x600 in 72 Hz") => [ '1024x768@60', "31.5-48.5" , "55-90" ], - __("High Frequency SVGA, 1024x768 in 70 Hz") => [ '1024x768@70', "31.5-57.0" , "50-90" ], - __("Multi-frequency that can do 1280x1024 in 60 Hz") => [ '1280x1024@60', "31.5-64.3" , "50-90" ], - __("Multi-frequency that can do 1280x1024 in 74 Hz") => [ '1280x1024@74', "31.5-79.0" , "50-100" ], - __("Multi-frequency that can do 1280x1024 in 76 Hz") => [ '1280x1024@76', "31.5-82.0" , "40-100" ], - __("Monitor that can do 1600x1200 in 70 Hz") => [ '1600x1200@70', "31.5-88.0" , "50-120" ], - __("Monitor that can do 1600x1200 in 76 Hz") => [ '1600x1200@76', "31.5-94.0" , "50-160" ], + __("Standard VGA, 640x480 at 60 Hz") => [ '640x480@60', "31.5" , "60" ], + __("Standard VGA, 640x480 at 60 Hz") => [ '640x480@60', "31.5" , "60" ], + __("Super VGA, 800x600 at 56 Hz") => [ '800x600@56', "31.5-35.1" , "55-60" ], + __("8514 Compatible, 1024x768 at 87 Hz interlaced (no 800x600)") => [ '8514 compatible', "31.5,35.5" , "60,70,87" ], + __("Super VGA, 1024x768 at 87 Hz interlaced, 800x600 at 56 Hz") => [ '1024x768@87i', "31.5,35.15,35.5" , "55-90" ], + __("Extended Super VGA, 800x600 at 60 Hz, 640x480 at 72 Hz") => [ '800x600@60', "31.5-37.9" , "55-90" ], + __("Non-Interlaced SVGA, 1024x768 at 60 Hz, 800x600 at 72 Hz") => [ '1024x768@60', "31.5-48.5" , "55-90" ], + __("High Frequency SVGA, 1024x768 at 70 Hz") => [ '1024x768@70', "31.5-57.0" , "50-90" ], + __("Multi-frequency that can do 1280x1024 at 60 Hz") => [ '1280x1024@60', "31.5-64.3" , "50-90" ], + __("Multi-frequency that can do 1280x1024 at 74 Hz") => [ '1280x1024@74', "31.5-79.0" , "50-100" ], + __("Multi-frequency that can do 1280x1024 at 76 Hz") => [ '1280x1024@76', "31.5-82.0" , "40-100" ], + __("Monitor that can do 1600x1200 at 70 Hz") => [ '1600x1200@70', "31.5-88.0" , "50-120" ], + __("Monitor that can do 1600x1200 at 76 Hz") => [ '1600x1200@76', "31.5-94.0" , "50-160" ], ); -# * Screen/video card configuration. -%ramdacs = ( - __("No RAMDAC Setting (recommended)") => '', - __("AT&T 20C490 (S3 and AGX servers, ARK driver)"), => 'att20c490', - __("AT&T 20C498/21C498/22C498 (S3, autodetected)"), => 'att20c498', - __("AT&T 20C409/20C499 (S3, autodetected)"), => 'att20c409', - __("AT&T 20C505 (S3)"), => 'att20c505', - __("BrookTree BT481 (AGX)"), => 'bt481', - __("BrookTree BT482 (AGX)"), => 'bt482', - __("BrookTree BT485/9485 (S3)"), => 'bt485', - __("Sierra SC15025 (S3, AGX)"), => 'sc15025', - __("S3 GenDAC (86C708) (autodetected)"), => 's3gendac', - __("S3 SDAC (86C716) (autodetected)"), => 's3_sdac', - __("STG-1700 (S3, autodetected)"), => 'stg1700', - __("STG-1703 (S3, autodetected)"), => 'stg1703', - __("TI 3020 (S3)"), => 'ti3020', - __("TI 3025 (S3, autodetected)"), => 'ti3025', - __("TI 3026 (S3, autodetected)"), => 'ti3026', - __("IBM RGB 514 (S3, autodetected)"), => 'ibm_rgb514', - __("IBM RGB 524 (S3, autodetected)"), => 'ibm_rgb524', - __("IBM RGB 525 (S3, autodetected)"), => 'ibm_rgb525', - __("IBM RGB 526 (S3)"), => 'ibm_rgb526', - __("IBM RGB 528 (S3, autodetected)"), => 'ibm_rgb528', - __("ICS5342 (S3, ARK)"), => 'ics5342', - __("ICS5341 (W32)"), => 'ics5341', - __("IC Works w30C516 ZoomDac (ARK)"), => 'zoomdac', - __("Normal DAC"), => 'normal', +@vsyncranges = ("50-70", "50-90", "50-100", "40-150"); + +@hsyncranges = ( + "31.5", + "31.5-35.1", + "31.5, 35.5", + "31.5, 35.15, 35.5", + "31.5-37.9", + "31.5-48.5", + "31.5-57.0", + "31.5-64.3", + "31.5-79.0", + "31.5-82.0", + "31.5-88.0", + "31.5-94.0", ); -@clockchip_name = ( - __("No Clockchip Setting (recommended)") => '', - __("Chrontel 8391") => 'ch8391', - __("ICD2061A and compatibles (ICS9161A => DCS2824)") => 'icd2061a', - __("ICS2595") => 'ics2595', - __("ICS5342 (similar to SDAC, but not completely compatible)") => 'ics5342', - __("ICS5341") => 'ics5341', - __("S3 GenDAC (86C708) and ICS5300 (autodetected)") => 's3gendac', - __("S3 SDAC (86C716)") => 's3_sdac', - __("STG 1703 (autodetected)") => 'stg1703', - __("Sierra SC11412") => 'sc11412', - __("TI 3025 (autodetected)") => 'ti3025', - __("TI 3026 (autodetected)") => 'ti3026', - __("IBM RGB 51x/52x (autodetected)") => 'ibm_rgb5xx', +%min_hsync4wres = ( + 640 => 31.5, + 800 => 35.1, + 1024 => 35.5, + 1152 => 44.0, + 1280 => 51.0, + 1600 => 75.0, ); +%lines = ( +#- 'Cirrus Logic|GD 5446' => [ ' Option "no_bitblt"' ], + 'Silicon Integrated Systems [SiS]|86C326' => [ qq( Option "noaccel"\n Option "sw_cursor") ], +#- 'Trident Microsystems|Cyber 9525' => [ ' Option "noaccel"' ], +#- 'S3 Inc.|86c368 [Trio 3D/2X]' => [ ' ChipID 0x8a10' ], +); +#- most usefull XFree86-4.0.1 server options. Default values is the first ones. +@options_serverflags = ( + 'NoTrapSignals' => [ "Off", "On" ], + 'DontZap' => [ "Off", "On" ], + 'DontZoom' => [ "Off", "On" ], + 'DisableVidModeExtension' => [ "Off", "On" ], + 'AllowNonLocalXvidtune' => [ "Off", "On" ], + 'DisableModInDev' => [ "Off", "On" ], + 'AllowNonLocalModInDev' => [ "Off", "On" ], + 'AllowMouseOpenFail' => [ "False", "True" ], + 'VTSysReq' => [ "Off", "On" ], + 'BlankTime' => [ "10", "5", "3", "15", "30" ], + 'StandByTime' => [ "20", "10", "6", "30", "60" ], + 'SuspendTime' => [ "30", "15", "9", "45", "90" ], + 'OffTime' => [ "40", "20", "12", "60", "120" ], + 'Pixmap' => [ "32", "24" ], + 'PC98' => [ "auto-detected", "False", "True" ], + 'NoPM' => [ "False", "True" ], +); +#- most usefull server options have to be accessible at the beginning, since +#- no more than a small set of options will be available for the user, maybe ? +@options = ( + [ 'DPMS', 'XFree86', '.*' ], + [ 'SyncOnGreen', 'XFree86', '.*' ], + [ 'power_saver', 'Mono', '.*' ], + [ 'hibit_low', 'VGA16', 'Tseng.*ET4000' ], + [ 'hibit_high', 'VGA16', 'Tseng.*ET4000' ], + [ 'power_saver', 'VGA16', '.*' ], + [ 'noaccel', 'SVGA', 'Cirrus|C&T|SiS|Oak|Western Digital|Alliance|Trident|Tseng' ], + [ 'no_accel', 'SVGA', 'ARK|MGA|i740|Oak|ET6000|W32|Media.*GX|Neomagic' ], + [ 'linear', 'SVGA', 'Cirrus|ET6000|ET4000/W32p rev [CD]|Oak|Neomagic|Triden|Tseng' ], + [ 'nolinear', 'SVGA', 'Cirrus|C&T|Trident' ], + [ 'no_linear', 'SVGA', 'ARK|SiS|Neomagic|Tseng' ], + [ 'no_bitblt', 'SVGA', 'Cirrus|C&T|SiS' ], + [ 'no_imageblt', 'SVGA', 'Cirrus|C&T|SiS' ], + [ 'sw_cursor', 'SVGA', '.*' ], + [ 'slow_dram', 'SVGA', 'Cirrus|Trident|ET6000|W32|Western Digital|Tseng' ], + [ 'mga_sdram', 'SVGA', 'MGA' ], + [ 'no_pixmap_cache', 'SVGA', 'ARK|Cirrus|C&T|MGA|SiS|Trident.*9440|Trident.*9680|Tseng' ], + [ 'no_mmio', 'SVGA', 'Cirrus|Neomagic|Trident' ], + [ 'pci_burst_off', 'SVGA', 'ET6000|W32|Trident|Tseng' ], + [ 'hw_clocks', 'SVGA', 'SiS|C&T' ], + [ 'use_modeline', 'SVGA', 'C&T' ], + [ 'enable_bitblt', 'SVGA', 'Oak' ], + [ 'w32_interleave_off', 'SVGA', 'ET6000|W32|Tseng' ], + [ 'fifo_conservative', 'SVGA', 'Cirrus|ARK|SiS|Oak' ], + [ 'fifo_moderate', 'SVGA', 'Cirrus|ARK|SiS' ], + [ 'all_wait', 'SVGA', 'Oak' ], + [ 'one_wait', 'SVGA', 'Oak' ], + [ 'first_wait', 'SVGA', 'Oak' ], + [ 'first_wwait', 'SVGA', 'Oak' ], + [ 'write_wait', 'SVGA', 'Oak' ], + [ 'read_wait', 'SVGA', 'Oak' ], + [ 'clgd6225_lcd', 'SVGA', 'Cirrus' ], + [ 'fix_panel_size', 'SVGA', 'C&T' ], + [ 'lcd_center', 'SVGA', 'C&T|Neomagic|Trident' ], + [ 'cyber_shadow', 'SVGA', 'Trident' ], + [ 'STN', 'SVGA', 'C&T' ], + [ 'no_stretch', 'SVGA', 'C&T|Cirrus|Neomagic|Trident' ], + [ 'no_prog_lcd_mode_regs', 'SVGA', 'Neomagic' ], + [ 'prog_lcd_mode_stretch', 'SVGA', 'Neomagic' ], + [ 'suspend_hack', 'SVGA', 'C&T' ], + [ 'use_18bit_bus', 'SVGA', 'C&T' ], + [ 'hibit_low', 'SVGA', 'Tseng.*ET4000' ], + [ 'hibit_high', 'SVGA', 'Tseng.*ET4000' ], + [ 'probe_clocks', 'SVGA', 'Cirrus' ], + [ 'power_saver', 'SVGA', '.*' ], + [ 'use_vlck1', 'SVGA', 'C&T' ], + [ 'sgram', 'SVGA', 'i740' ], + [ 'sdram', 'SVGA', 'i740' ], + [ 'no_2mb_banksel', 'SVGA', 'Cirrus' ], + [ 'tgui_pci_read_on', 'SVGA', 'Trident' ], + [ 'tgui_pci_write_on', 'SVGA', 'Trident' ], + [ 'no_program_clocks', 'SVGA', 'Trident' ], + [ 'mmio', 'SVGA', 'Cirrus|C&T|Neomagic' ], + [ 'sync_on_green', 'SVGA', 'C&T|MGA' ], + [ 'pci_retry', 'SVGA', 'Tseng|MGA|Cirrus' ], + [ 'hw_cursor', 'SVGA', 'C&T|SiS|ARK|ET6000|i740|Tseng' ], + [ 'xaa_no_color_exp', 'SVGA', 'C&T|Cirrus|Trident|Tseng' ], + [ 'xaa_benchmarks', 'SVGA', 'C&T' ], + [ 'pci_burst_on', 'SVGA', 'Trident|Tseng' ], + [ 'prog_lcd_mode_regs', 'SVGA', 'Neomagic' ], + [ 'no_prog_lcd_mode_stretch', 'SVGA', 'Neomagic' ], + [ 'no_wait', 'SVGA', 'Oak' ], + #- [ 'med_dram', 'SVGA', 'Cirrus|Trident|Western Digital' ], #- WARNING, MAY DAMAGE CARD + #- [ 'fast_dram', 'SVGA', 'C&T|Cirrus|ET[46]000|Trident|Western Digital' ], #- WARNING, MAY DAMAGE CARD + #- [ 'fast_vram', 'SVGA', 'SiS' ], #- WARNING, MAY DAMAGE CARD + #- [ 'clock_50', 'SVGA', 'Oak' ], #- WARNING, MAY DAMAGE CARD + #- [ 'clock_66', 'SVGA', 'Oak' ], #- WARNING, MAY DAMAGE CARD + #- [ 'fifo_aggressive', 'SVGA', 'Cirrus|ARK|SiS|Oak' ], #- WARNING, MAY DAMAGE CARD + #- [ 'override_validate_mode', 'SVGA', 'Neomagic' ], #- WARNING, MAY DAMAGE CARD + #- [ 'tgui_mclk_66', 'SVGA', 'Trident' ], #- WARNING, MAY DAMAGE CARD + #- [ 'favour_bitblt', 'SVGA', 'Cirrus' ], #- OBSELETE + [ 'sw_cursor', '3DLabs', '.*' ], + [ 'no_pixmap_cache', '3DLabs', '.*' ], + [ 'no_accel', '3DLabs', '.*' ], + [ 'firegl_3000', '3DLabs', '.*' ], + [ 'sync_on_green', '3DLabs', '.*' ], + [ 'pci_retry', '3DLabs', '.*' ], + #- [ 'overclock_mem', '3DLabs', '.*' ], #- WARNING, MAY DAMAGE CARD + [ 'dac_8_bit', 'I128', '.*' ], + [ 'no_accel', 'I128', '.*' ], + [ 'sync_on_green', 'I128', '.*' ], + [ 'composite', 'Mach32', '.*' ], + [ 'sw_cursor', 'Mach32', '.*' ], + [ 'dac_8_bit', 'Mach32', '.*' ], + [ 'ast_mach32', 'Mach32', '.*' ], + [ 'intel_gx', 'Mach32', '.*' ], + [ 'no_linear', 'Mach32', '.*' ], + [ 'sw_cursor', 'Mach64', '.*' ], + [ 'nolinear', 'Mach64', '.*' ], + [ 'no_block_write', 'Mach64', '.*' ], + [ 'block_write', 'Mach64', '.*' ], + [ 'fifo_conservative', 'Mach64', '.*' ], + [ 'no_font_cache', 'Mach64', '.*' ], + [ 'no_pixmap_cache', 'Mach64', '.*' ], + [ 'composite', 'Mach64', '.*' ], + [ 'power_saver', 'Mach64', '.*' ], + [ 'no_program_clocks', 'Mach64', '.*' ], + [ 'no_bios_clocks', 'Mach64', '.*' ], + [ 'dac_6_bit', 'Mach64', '.*' ], + [ 'dac_8_bit', 'Mach64', '.*' ], + [ 'hw_cursor', 'Mach64', '.*' ], + #- [ 'override_bios', 'Mach64', '.*' ], #- WARNING, MAY DAMAGE CARD + [ 'sw_cursor', 'P9000', '.*' ], + [ 'noaccel', 'P9000', '.*' ], + [ 'sync_on_green', 'P9000', '.*' ], + [ 'vram_128', 'P9000', '.*' ], + [ 'nolinear', 'S3', '.*' ], + [ 'dac_8_bit', 'S3', '.*' ], + [ 'slow_vram', 'S3', 'S3.*964' ], + [ 'stb_pegasus', 'S3', 'S3.*928' ], + [ 'SPEA_Mercury', 'S3', 'S3.*(928|964)' ], + [ 'number_nine', 'S3', 'S3.*(864|928)' ], + [ 'lcd_center', 'S3', 'S3.*Aurora64V' ], + [ 'noaccel', 'S3V', '.*' ], + [ 'slow_edodram', 'S3V', '.*' ], + [ 'pci_burst_on', 'S3V', '.*' ], + [ 'early_ras_precharge', 'S3V', '.*' ], + [ 'late_ras_precharge', 'S3V', '.*' ], + [ 'fifo_conservative', 'S3V', '.*' ], + [ 'fifo_aggressive', 'S3V', '.*' ], + [ 'fifo_moderate', 'S3V', '.*' ], + [ 'lcd_center', 'S3V', 'S3.*ViRGE\/MX' ], + [ 'hw_cursor', 'S3V', '.*' ], + [ 'pci_retry', 'S3V', '.*' ], + [ 'dac_6_bit', 'AGX', '.*' ], + [ 'dac_8_bit', 'AGX', '.*' ], + [ 'sync_on_green', 'AGX', '.*' ], + [ '8_bit_bus', 'AGX', '.*' ], + [ 'wait_state', 'AGX', '.*' ], + [ 'no_wait_state', 'AGX', '.*' ], + [ 'noaccel', 'AGX', '.*' ], + [ 'crtc_delay', 'AGX', '.*' ], + [ 'fifo_conserv', 'AGX', '.*' ], + [ 'fifo_aggressive', 'AGX', '.*' ], + [ 'fifo_moderate', 'AGX', '.*' ], + [ 'vram_delay_latch', 'AGX', '.*' ], + [ 'vram_delay_ras', 'AGX', '.*' ], + [ 'vram_extend_ras', 'AGX', '.*' ], + [ 'slow_dram', 'AGX', '.*' ], + [ 'slow_vram', 'AGX', '.*' ], + [ 'med_dram', 'AGX', '.*' ], + [ 'med_vram', 'AGX', '.*' ], + [ 'fast_dram', 'AGX', '.*' ], + [ 'fast_vram', 'AGX', '.*' ], + [ 'engine_delay', 'AGX', '.*' ], + [ 'vram_128', 'AGX', '.*' ], + [ 'vram_256', 'AGX', '.*' ], + [ 'refresh_20', 'AGX', '.*' ], + [ 'refresh_25', 'AGX', '.*' ], + [ 'screen_refresh', 'AGX', '.*' ], + [ 'vlb_a', 'AGX', '.*' ], + [ 'vlb_b', 'AGX', '.*' ], + [ 'slow_dram', 'W32', '.*' ], + [ 'pci_burst_off', 'W32', '.*' ], + [ 'w32_interleave_off', 'W32', '.*' ], + [ 'no_accel', 'W32', '.*' ], + [ 'nolinear', '8514', '.*' ], + [ 'sw_cursor', '8514', '.*' ], + [ 'no_block_write', '8514', '.*' ], + [ 'block_write', '8514', '.*' ], + [ 'fifo_conservative', '8514', '.*' ], + [ 'no_font_cache', '8514', '.*' ], + [ 'no_pixmap_cache', '8514', '.*' ], + [ 'composite', '8514', '.*' ], + [ 'power_saver', '8514', '.*' ], + [ 'power_saver', 'FBDev', '.*' ], +); +%xkb_options = ( + 'ru(winkeys)' => [ 'XkbVariant "winkeys"', 'XkbOptions "grp:caps_toggle"' ], + 'jp' => [ 'XkbModel "jp106"' ], +); - - - - - - - - - -$intro_text = " -This program will create a basic XF86Config file, based on menu selections you make. - -The XF86Config file usually resides in /usr/X11R6/lib/X11 or /etc/X11. A -sample XF86Config file is supplied with XFree86; it is configured for a -standard VGA card and monitor with 640x480 resolution. - -You can either take the sample XF86Config as a base and edit it for your -configuration, or let this program produce a base XF86Config file for your -configuration and fine-tune it. Refer to /usr/X11R6/lib/X11/doc/README.Config -for a detailed overview of the configuration process. - -For accelerated servers (including accelerated drivers in the SVGA server), -there are many chipset and card-specific options and settings. This program -does not know about these. On some configurations some of these settings must -be specified. Refer to the server man pages and chipset-specific READMEs. - -Before continuing with this program, make sure you know the chipset and -amount of video memory on your video card. SuperProbe can help with this. -It is also helpful if you know what server you want to run."; - -$finalcomment_text = " -configuration file has been written. Take a look at it before running 'startx'. -Note that the XF86Config file must be in one of the directories searched by the -server (e.g. /etc/X11/XF86Config) in order to be used. Within the server press -ctrl, alt and '+' simultaneously to cycle video resolutions. Pressing ctrl, alt -and backspace simultaneously immediately exits the server (use if the monitor -doesn't sync for a particular mode). - -For further configuration, refer to /usr/X11R6/lib/X11/doc/README.Config. -"; - -$s3_comment = ' -# Use Option "nolinear" if the server doesn\'t start up correctly -# (this avoids the linear framebuffer probe). If that fails try -# option \"nomemaccess\". -# -# Refer to /usr/X11R6/lib/doc/README.S3, and the XF86_S3 man page. -'; - -$cirrus_comment = ' -# Use Option \"no_bitblt\" if you have graphics problems. If that fails -# try Option \"noaccel\". -# Refer to /usr/X11R6/lib/doc/README.cirrus. -# To allow linear addressing, uncomment the Option line and the -# address that the card maps the framebuffer to. -'; - -$probeonlywarning_text = ' -It is possible that the hardware detection routines in the server some how -cause the system to crash and the screen to remain blank. If this is the -case, skip this step the next time. The server may need a -Ramdac, ClockChip or special option (e.g. "nolinear" for S3) to probe -and start-up correctly. -'; - -$monitorintro_text = __(' -Now we want to set the specifications of the monitor. The two critical -parameters are the vertical refresh rate, which is the rate at which the -the whole screen is refreshed, and most importantly the horizontal sync rate, -which is the rate at which scanlines are displayed. - -The valid range for horizontal sync and vertical sync should be documented -in the manual of your monitor. If in doubt, check the monitor database -/usr/X11R6/lib/X11/doc/Monitors to see if your monitor is there. -'); - -$hsyncintro_text = __(' -You must indicate the horizontal sync range of your monitor. You can either -select one of the predefined ranges below that correspond to industry- -standard monitor types, or give a specific range. - -It is VERY IMPORTANT that you do not specify a monitor type with a horizontal -sync range that is beyond the capabilities of your monitor. If in doubt, -choose a conservative setting. -'); - -$vsyncintro_text = __(' -You must indicate the vertical sync range of your monitor. You can either -select one of the predefined ranges below that correspond to industry- -standard monitor types, or give a specific range. For interlaced modes, -the number that counts is the high one (e.g. 87 Hz rather than 43 Hz). -'); - -$XF86firstchunk_text = ' -# File generated by XConfigurator. +$XF86firstchunk_text = q( +# File generated by XFdrake. # ********************************************************************** -# Refer to the XF86Config(4/5) man page for details about the format of +# Refer to the XF86Config(4/5) man page for details about the format of # this file. # ********************************************************************** -# ********************************************************************** -# Files section. This allows default font and rgb paths to be set -# ********************************************************************** - Section "Files" -# The location of the RGB database. Note, this is the name of the -# file minus the extension (like ".txt" or ".db"). There is normally -# no need to change the default. - RgbPath "/usr/X11R6/lib/X11/rgb" # Multiple FontPath entries are allowed (they are concatenated together) -# By default, Red Hat 6.0 and later now use a font server independent of +# By default, Mandrake 6.0 and later now use a font server independent of # the X server to render fonts. FontPath "unix/:-1" @@ -215,7 +385,7 @@ EndSection Section "ServerFlags" - # Uncomment this to cause a core dump at the spot where a signal is + # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging #NoTrapSignals @@ -228,12 +398,18 @@ Section "ServerFlags" # sequences. This allows clients to receive these key events. #DontZoom + # This allows the server to start up even if the + # mouse device can't be opened/initialised. + AllowMouseOpenFail +); + +$XF86firstchunk_text2 = q( EndSection # ********************************************************************** # Input devices # ********************************************************************** -'; +); $keyboardsection_start = ' # ********************************************************************** @@ -248,29 +424,90 @@ Section "Keyboard" # following line #Protocol "Xqueue" - AutoRepeat 500 5 + AutoRepeat 250 30 - # Let the server do the NumLock processing. This should only be + # Let the server do the NumLock processing. This should only be # required when using pre-R6 clients #ServerNumLock # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) - #Xleds 1 2 3 + #Xleds "1 2 3" - #To set the LeftAlt to Meta, RightAlt key to ModeShift, + #To set the LeftAlt to Meta, RightAlt key to ModeShift, #RightCtl key to Compose, and ScrollLock key to ModeLock: LeftAlt Meta -'; - -$keyboardsection_part2 = ' - ScrollLock Compose - RightCtl Control + RightAlt Meta + ScrollLock Compose + RightCtl Control # To disable the XKEYBOARD extension, uncomment XkbDisable. # XkbDisable +'; + +$keyboardsection_start_v4 = ' +# ********************************************************************** +# Keyboard section +# ********************************************************************** + +Section "InputDevice" + + Identifier "Keyboard1" + Driver "Keyboard" + Option "AutoRepeat" "250 30" +'; + +if (arch() =~ /^sparc/) { + $keyboardsection_part3 = ' +# To customise the XKB settings to suit your keyboard, modify the +# lines below (which are the defaults). For example: +# XkbModel "type6" +# If you have a SUN keyboard, you may use: +# XkbModel "sun" +# +# Then to change the language, change the Layout setting. +# For example, a german layout can be obtained with: +# XkbLayout "de" +# or: +# XkbLayout "de" +# XkbVariant "nodeadkeys" +# +# If you\'d like to switch the positions of your capslock and +# control keys, use: +# XkbOptions "ctrl:swapcaps" +# These are the default XKB settings for XFree86 on SUN: +# XkbRules "sun" +# XkbModel "type5_unix" +# XkbLayout "us" +# XkbCompat "compat/complete" +# XkbTypes "types/complete" +# XkbKeycodes "sun(type5)" +# XkbGeometry "sun(type5)" +# XkbSymbols "sun/us(sun5)" + + XkbRules "sun" + XkbModel "sun" + XkbLayout "us" + XkbCompat "compat/complete" + XkbTypes "types/complete" + XkbKeycodes "sun(type5)" + XkbGeometry "sun(type5)" + XkbSymbols "sun/us(sun5)" +'; +$keyboardsection_part3_v4 = ' + Option "XkbRules" "sun" + Option "XkbModel" "sun" + Option "XkbLayout" "us" + Option "XkbCompat" "compat/complete" + Option "XkbTypes" "types/complete" + Option "XkbKeycodes" "sun(type5)" + Option "XkbGeometry" "sun(type5)" + Option "XkbSymbols" "sun/us(sun5)" +'; +} else { +$keyboardsection_part3 = ' # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: @@ -296,20 +533,26 @@ $keyboardsection_part2 = ' # XkbVariant "" # XkbOptions "" - XkbKeycodes "xfree86" - XkbTypes "default" - XkbCompat "default" - XkbSymbols "us(pc101)" - XkbGeometry "pc" - XkbRules "xfree86" - XkbModel "pc101" + XkbKeycodes "xfree86" + XkbTypes "default" + XkbCompat "default" + XkbSymbols "us(pc105)" + XkbGeometry "pc" + XkbRules "xfree86" + XkbModel "pc105" '; +$keyboardsection_part3_v4 = ' + Option "XkbRules" "xfree86" + Option "XkbModel" "pc105" +'; +} + $keyboardsection_end = ' EndSection '; -$pointersection_text1 = ' +$pointersection_text = ' # ********************************************************************** # Pointer section # ********************************************************************** @@ -317,20 +560,15 @@ $pointersection_text1 = ' Section "Pointer" '; -$pointersection_text2 = ' - -# When using XQUEUE, comment out the above two lines, and uncomment -# the following line. - -# Protocol "Xqueue" - -# Baudrate and SampleRate are only for some Logitech mice +$pointersection_text_v4 = ' +# ********************************************************************** +# Pointer section +# ********************************************************************** -# BaudRate 9600 -# SampleRate 150 +Section "InputDevice" -# Emulate3Buttons is an option for 2-button Microsoft mice -# Emulate3Timeout is the timeout in milliseconds (default is 50ms) + Identifier "Mouse1" + Driver "mouse" '; $monitorsection_text1 = ' @@ -486,9 +724,9 @@ Modeline "1600x1200" 220 1600 1616 1808 2080 1200 1204 1207 1244 +HSync +VS # 1280x1024 @ 100 Hz, 107.16 kHz hsync Modeline "1280x1024" 181.75 1280 1312 1440 1696 1024 1031 1046 1072 -HSync -VSync -# 1800x1440 @ 64Hz, 96.15 kHz hsync +# 1800x1440 @ 64Hz, 96.15 kHz hsync ModeLine "1800X1440" 230 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync -# 1800x1440 @ 70Hz, 104.52 kHz hsync +# 1800x1440 @ 70Hz, 104.52 kHz hsync ModeLine "1800X1440" 250 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync # 512x384 @ 78 Hz, 31.50 kHz hsync @@ -528,21 +766,23 @@ $devicesection_text = ' # Graphics device section # ********************************************************************** -# Any number of graphics device sections may be present - Section "Device" - Identifier "Generic VGA" - VendorName "Unknown" - BoardName "Unknown" + Identifier "Generic VGA" Chipset "generic" +EndSection -# VideoRam 256 +'; -# Clocks 25.2 28.3 +$devicesection_text_v4 = ' +# ********************************************************************** +# Graphics device section +# ********************************************************************** +Section "Device" + Identifier "Generic VGA" + Driver "vga" EndSection -# Device configured by Xconfigurator: '; $screensection_text1 = ' |