diff options
| -rwxr-xr-x | create_arm_img_urpmi.sh | 11 | ||||
| -rw-r--r-- | init.d/mandrake_firstime | 23 | ||||
| -rw-r--r-- | rpi/mageia4arm.cfg | 10 | ||||
| -rw-r--r-- | rpi2/10-monitor.conf | 3 | ||||
| -rw-r--r-- | rpi2/10-vchiq-permissions.rules | 1 | ||||
| -rwxr-xr-x | rpi2/bcm2836-rpi-2-b.dtb | bin | 0 -> 13018 bytes | |||
| -rwxr-xr-x | rpi2/bcm2837-rpi-3-b-plus.dtb | bin | 0 -> 14348 bytes | |||
| -rwxr-xr-x | rpi2/bcm2837-rpi-3-b.dtb | bin | 0 -> 14096 bytes | |||
| -rw-r--r-- | rpi2/boot.cmd | 5 | ||||
| -rw-r--r-- | rpi2/brcmfmac43430-sdio.txt | 66 | ||||
| -rw-r--r-- | rpi2/brcmfmac43455-sdio.clm_blob | bin | 0 -> 11231 bytes | |||
| -rw-r--r-- | rpi2/brcmfmac43455-sdio.txt | 92 | ||||
| -rw-r--r-- | rpi2/config.txt | 1193 | ||||
| -rw-r--r-- | rpi2/extlinux.conf | 10 | ||||
| -rw-r--r-- | rpi2/mageia4arm.cfg | 60 | ||||
| -rw-r--r-- | rpi2/mageia4arm.cfg.original | 59 | ||||
| -rw-r--r-- | rpi2/mageia4arm.cfg~ | 57 | ||||
| -rw-r--r-- | rpi2/modprobe.conf | 3 | ||||
| -rw-r--r-- | rpi2/second_stage_install.sh | 41 | ||||
| -rw-r--r-- | rpi3+/mageia4arm.cfg | 61 | ||||
| -rw-r--r-- | xu4/mageia4arm.cfg | 6 |
21 files changed, 1689 insertions, 12 deletions
diff --git a/create_arm_img_urpmi.sh b/create_arm_img_urpmi.sh index 6847d39..90ac4fa 100755 --- a/create_arm_img_urpmi.sh +++ b/create_arm_img_urpmi.sh @@ -39,7 +39,8 @@ function error() SOURCE_PATH="$(/bin/dirname "$(readlink -f "$0")")" INSTALL_PATH="$SOURCE_PATH/arm" FILES_PATH="$SOURCE_PATH/files" -CMDNAME=$(/bin/basename -z "$0") +info $0 +CMDNAME=$(/bin/basename "$0") #while read -r;do # for MAGEIA_VERSION in $REPLY @@ -71,7 +72,7 @@ function help() echo "--target target system (for now rpi, odroid)" echo "--target-version version of the target (0, 1, 2, 3 for rpi, 3 or 4 for odroid)" echo "--config Path to config files" - echo "--bootfs filesystem of boot partition (ext4 or vfat) default: etx4" + echo "--bootfs filesystem of boot partition (ext4 or vfat) default: ext4" echo -e "\nFor image size, make sure it fit on physical support. (Default size is 7 Go)" } @@ -86,7 +87,7 @@ function clean() umount "$BUILD_PATH/dev" if ! [ $? -ne 0 ];then error "line $LINENO can't unmount $BUILD_PATH/dev : exiting" - exit 1 + #exit 1 fi fi if ! [ -z "$(mountpoint -qd "$BUILD_PATH/sys")" ];then @@ -94,7 +95,7 @@ function clean() umount "$BUILD_PATH/sys" if ! [ $? -ne 0 ];then error "line $LINENO can't unmount $BUILD_PATH/sys : exiting" - exit 1 + #exit 1 fi fi if ! [ -z "$(mountpoint -qd "$BUILD_PATH/proc")" ];then @@ -102,7 +103,7 @@ function clean() umount "$BUILD_PATH/proc" if ! [ $? -ne 0 ];then error "line $LINENO can't unmount $BUILD_PATH/proc : exiting" - exit 1 + #exit 1 fi fi # Removing old Build directory diff --git a/init.d/mandrake_firstime b/init.d/mandrake_firstime new file mode 100644 index 0000000..8e7216e --- /dev/null +++ b/init.d/mandrake_firstime @@ -0,0 +1,23 @@ +#!/bin/sh +# Description: Launch Mageia Configuration for the first time. +# (c) Mandriva, Chmouel Boudjnah <chmouel@mandriva.com> +# $Id$ + +FLO=/var/log/first_boot_log +touch $FLO + +. /etc/rc.d/init.d/functions + +# If fail erase the temporary file +trap 'rm -f /var/lock/TMP_1ST' 1 2 3 15 + +SYSTEM= + + + + + +[ -s $FLO ] || rm -f $FLO + +# Finish +rm -f /var/lock/TMP_1ST diff --git a/rpi/mageia4arm.cfg b/rpi/mageia4arm.cfg index 5bea977..e05172d 100644 --- a/rpi/mageia4arm.cfg +++ b/rpi/mageia4arm.cfg @@ -19,7 +19,7 @@ MAGEIA_VERSION="7" ARM_VERSION="armv7hl" #target plateform (xu3-4 or rpi) -TARGET="rpi" +TARGET="rpi" #version of the target # 0, 1, 2 ,3_32 for rpi and 3 or 4 for odroid TARGET_VERSION="3_32" @@ -29,7 +29,7 @@ MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSI #MIRROR="/mnt/STOCK/mageia/distrib/$MAGEIA_VERSION/$ARM_VERSION" # image will be created here -INSTALL_PATH="/mnt/perso/raspi-test" +INSTALL_PATH="/mnt/perso/raspi-test" # Build directory will be created here BUILD_PATH="$INSTALL_PATH/build" @@ -48,8 +48,8 @@ PASSWORD="raspberry" #root password ROOT_PWD="piroot" -#Hostname -HOSTNAME="$TARGET.$ID_USER" +#Hostname +HOSTNAME="$TARGET.$ID_USER" #Filesystem of boot partitions (default ext4 raspberry pi need vfat) BOOTFS="vfat" @@ -57,3 +57,5 @@ BOOTFS="vfat" #Path where the raspberry pi firmware is/will be installed FIRMWARE_PATH="$INSTALL_PATH" FIRMWARE_DIR="firmware-stable" +FIRMWARE_DOWNLOAD_URL="https://github.com/raspberrypi/firmware/archive/stable.zip" + diff --git a/rpi2/10-monitor.conf b/rpi2/10-monitor.conf new file mode 100644 index 0000000..6b319d7 --- /dev/null +++ b/rpi2/10-monitor.conf @@ -0,0 +1,3 @@ +Section "Extensions" + Option "DPMS" "Disable" +EndSection diff --git a/rpi2/10-vchiq-permissions.rules b/rpi2/10-vchiq-permissions.rules new file mode 100644 index 0000000..bacea0e --- /dev/null +++ b/rpi2/10-vchiq-permissions.rules @@ -0,0 +1 @@ +SUBSYSTEM=="vchiq",GROUP="video",MODE="0660" diff --git a/rpi2/bcm2836-rpi-2-b.dtb b/rpi2/bcm2836-rpi-2-b.dtb Binary files differnew file mode 100755 index 0000000..06ba65b --- /dev/null +++ b/rpi2/bcm2836-rpi-2-b.dtb diff --git a/rpi2/bcm2837-rpi-3-b-plus.dtb b/rpi2/bcm2837-rpi-3-b-plus.dtb Binary files differnew file mode 100755 index 0000000..9fa2dd4 --- /dev/null +++ b/rpi2/bcm2837-rpi-3-b-plus.dtb diff --git a/rpi2/bcm2837-rpi-3-b.dtb b/rpi2/bcm2837-rpi-3-b.dtb Binary files differnew file mode 100755 index 0000000..7ed21fb --- /dev/null +++ b/rpi2/bcm2837-rpi-3-b.dtb diff --git a/rpi2/boot.cmd b/rpi2/boot.cmd new file mode 100644 index 0000000..cf2b8ea --- /dev/null +++ b/rpi2/boot.cmd @@ -0,0 +1,5 @@ +fatload mmc 0:1 ${kernel_addr_r} vmlinuz +fatload mmc 0:1 ${fdt_addr} bcm2837-rpi-3-b.dtb +fatload mmc 0:1 ${ramdisk_addr_r} initrd.img +setenv bootargs console=ttyAMA0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait panic=10 +bootz ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr} diff --git a/rpi2/brcmfmac43430-sdio.txt b/rpi2/brcmfmac43430-sdio.txt new file mode 100644 index 0000000..ea4f648 --- /dev/null +++ b/rpi2/brcmfmac43430-sdio.txt @@ -0,0 +1,66 @@ +# NVRAM file for BCM943430WLPTH +# 2.4 GHz, 20 MHz BW mode + +# The following parameter values are just placeholders, need to be updated. +manfid=0x2d0 +prodid=0x0727 +vendid=0x14e4 +devid=0x43e2 +boardtype=0x0727 +boardrev=0x1101 +boardnum=22 +macaddr=00:90:4c:c5:12:38 +sromrev=11 +boardflags=0x00404201 +boardflags3=0x08000000 +xtalfreq=37400 +nocrc=1 +ag0=255 +aa2g=1 +ccode=ALL + +pa0itssit=0x20 +extpagain2g=0 +#PA parameters for 2.4GHz, measured at CHIP OUTPUT +pa2ga0=-168,7161,-820 +AvVmid_c0=0x0,0xc8 +cckpwroffset0=5 + +# PPR params +maxp2ga0=84 +txpwrbckof=6 +cckbw202gpo=0 +legofdmbw202gpo=0x66111111 +mcsbw202gpo=0x77711111 +propbw202gpo=0xdd + +# OFDM IIR : +ofdmdigfilttype=18 +ofdmdigfilttypebe=18 +# PAPD mode: +papdmode=1 +papdvalidtest=1 +pacalidx2g=42 +papdepsoffset=-22 +papdendidx=58 + +# LTECX flags +ltecxmux=0 +ltecxpadnum=0x0102 +ltecxfnsel=0x44 +ltecxgcigpio=0x01 + +il0macaddr=00:90:4c:c5:12:38 +wl0id=0x431b + +deadman_to=0xffffffff +# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG +muxenab=0x1 +# CLDO PWM voltage settings - 0x4 - 1.1 volt +#cldo_pwm=0x4 + +#VCO freq 326.4MHz +spurconfig=0x3 + +edonthd20l=-75 +edoffthd20ul=-80 diff --git a/rpi2/brcmfmac43455-sdio.clm_blob b/rpi2/brcmfmac43455-sdio.clm_blob Binary files differnew file mode 100644 index 0000000..09b930b --- /dev/null +++ b/rpi2/brcmfmac43455-sdio.clm_blob diff --git a/rpi2/brcmfmac43455-sdio.txt b/rpi2/brcmfmac43455-sdio.txt new file mode 100644 index 0000000..260c929 --- /dev/null +++ b/rpi2/brcmfmac43455-sdio.txt @@ -0,0 +1,92 @@ +# Cloned from bcm94345wlpagb_p2xx.txt +NVRAMRev=$Rev: 498373 $ +sromrev=11 +vendid=0x14e4 +devid=0x43ab +manfid=0x2d0 +prodid=0x06e4 +#macaddr=00:90:4c:c5:12:38 +macaddr=b8:27:eb:74:f2:6c +nocrc=1 +boardtype=0x6e4 +boardrev=0x1304 + +#XTAL 37.4MHz +xtalfreq=37400 + +btc_mode=1 +#------------------------------------------------------ +#boardflags: 5GHz eTR switch by default +# 2.4GHz eTR switch by default +# bit1 for btcoex +boardflags=0x00480201 +boardflags2=0x40800000 +boardflags3=0x48200100 +phycal_tempdelta=15 +rxchain=1 +txchain=1 +aa2g=1 +aa5g=1 +tssipos5g=1 +tssipos2g=1 +femctrl=0 +AvVmid_c0=1,165,2,100,2,100,2,100,2,100 +pa2ga0=-129,6525,-718 +pa2ga1=-149,4408,-601 +pa5ga0=-185,6836,-815,-186,6838,-815,-184,6859,-815,-184,6882,-818 +pa5ga1=-202,4285,-574,-201,4312,-578,-196,4391,-586,-201,4294,-575 +itrsw=1 +pdoffsetcckma0=2 +pdoffset2gperchan=0,-2,1,0,1,0,1,1,1,0,0,-1,-1,0 +pdoffset2g40ma0=16 +pdoffset40ma0=0x8888 +pdoffset80ma0=0x8888 +extpagain5g=2 +extpagain2g=2 +tworangetssi2g=1 +tworangetssi5g=1 +# LTECX flags +# WCI2 +ltecxmux=0 +ltecxpadnum=0x0504 +ltecxfnsel=0x22 +ltecxgcigpio=0x32 + +maxp2ga0=80 +ofdmlrbw202gpo=0x0022 +dot11agofdmhrbw202gpo=0x4442 +mcsbw202gpo=0x98444422 +mcsbw402gpo=0x98444422 +maxp5ga0=82,82,82,82 +mcsbw205glpo=0xb9555000 +mcsbw205gmpo=0xb9555000 +mcsbw205ghpo=0xb9555000 +mcsbw405glpo=0xb9555000 +mcsbw405gmpo=0xb9555000 +mcsbw405ghpo=0xb9555000 +mcsbw805glpo=0xb9555000 +mcsbw805gmpo=0xb9555000 +mcsbw805ghpo=0xb9555000 + +swctrlmap_2g=0x00000000,0x00000000,0x00000000,0x010000,0x3ff +swctrlmap_5g=0x00100010,0x00200020,0x00200020,0x010000,0x3fe +swctrlmapext_5g=0x00000000,0x00000000,0x00000000,0x000000,0x3 +swctrlmapext_2g=0x00000000,0x00000000,0x00000000,0x000000,0x3 + +vcodivmode=1 +deadman_to=481500000 + +ed_thresh2g=-54 +ed_thresh5g=-54 +eu_edthresh2g=-54 +eu_edthresh5g=-54 +ldo1=4 +rawtempsense=0x1ff +cckPwrIdxCorr=3 +cckTssiDelay=150 +ofdmTssiDelay=150 +txpwr2gAdcScale=1 +txpwr5gAdcScale=1 +dot11b_opts=0x3aa85 +cbfilttype=1 +fdsslevel_ch11=6 diff --git a/rpi2/config.txt b/rpi2/config.txt new file mode 100644 index 0000000..a27b5de --- /dev/null +++ b/rpi2/config.txt @@ -0,0 +1,1193 @@ +################################################################################ +## Raspberry Pi Configuration Settings +## +## Revision 16, 2013/06/22 +## +## Details taken from the eLinux wiki +## For up-to-date information please refer to wiki page. +## +## Wiki Location : http://elinux.org/RPiconfig +## +## +## Description: +## Details of each setting are described with each section that begins with +## a double hashed comment ('##') +## It is up to the user to remove the single hashed comment ('#') from each +## option they want to enable, and to set the specific value of that option. +## +## Overclock settings will be disabled at runtime if the SoC reaches temp_limit +## +################################################################################ + +#dtoverlay=vc4-kms-v3d,cma-128 + + + + + +################################################################################ +## Standard Definition Video Settings +################################################################################ + +## sdtv_mode +## defines the TV standard for composite output +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Normal NTSC (Default) +## 1 Japanese version of NTSC - no pedestal +## 2 Normal PAL +## 3 Brazilian version of PAL - 525/60 rather than 625/50, different +## subcarrier +## +#sdtv_mode=0 + +## sdtv_aspect +## defines the aspect ratio for composite output +## +## Value Description +## ------------------------------------------------------------------------- +## 1 4:3 (Default) +## 2 14:9 +## 3 16:9 +## +sdtv_aspect=3 + +## sdtv_disable_colourburst +## Disables colour burst on composite output. The picture will be +## monochrome, but possibly sharper +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Colour burst is enabled (Default) +## 1 Colour burst is disabled +## +#sdtv_disable_colourburst=1 + +################################################################################ +## High Definition Video Settings +################################################################################ + +## hdmi_safe +## Use "safe mode" settings to try to boot with maximum hdmi compatibility. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Disabled (Default) +## 1 Enabled (this does: hdmi_force_hotplug=1, +## hdmi_ignore_edid=0xa5000080, +## config_hdmi_boost=4, hdmi_group=2, +## hdmi_mode=4, disable_overscan=0, +## overscan_left=24, overscan_right=24, +## overscan_top=24, overscan_bottom=24) +## +#hdmi_safe=1 + +## hdmi_force_hotplug +## Pretends HDMI hotplug signal is asserted so it appears a HDMI display +## is attached +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Disabled (Default) +## 1 Use HDMI mode even if no HDMI monitor is detected +## +#hdmi_force_hotplug=1 + +## hdmi_ignore_hotplug +## Pretends HDMI hotplug signal is not asserted so it appears a HDMI +## display is not attached +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Disabled (Default) +## 1 Use composite mode even if HDMI monitor is detected +## +#hdmi_ignore_hotplug=1 + +## hdmi_drive +## chooses between HDMI and DVI modes +## +## Value Description +## ------------------------------------------------------------------------- +## 1 Normal DVI mode (No sound) +## 2 Normal HDMI mode (Sound will be sent if supported and enabled) +## +#hdmi_drive=2 + +## hdmi_ignore_edid +## Enables the ignoring of EDID/display data +## +#hdmi_ignore_edid=0xa5000080 + +## hdmi_edid_file +## Read the EDID data from the edid.dat file instead of from the attached +## device +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Read EDID data from attached device (Default) +## 1 Read EDID data from edid.txt file +## +#hdmi_edid_file=1 + +## hdmi_ignore_edid_audio +## Pretends all audio formats are unsupported by display. This means ALSA +## will default to analogue. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use EDID provided values (Default) +## 1 Pretend all audio formats are unsupported +## +#hdmi_ignore_edid_audio=1 + +## hdmi_force_edid_audio +## Pretends all audio formats are supported by display, allowing +## passthrough of DTS/AC3 even when not reported as supported. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use EDID provided values (Default) +## 1 Pretend all audio formats are supported +## +#hdmi_force_edid_audio=1 + +## hdmi_force_edid_3d +## Pretends all CEA modes support 3D even when edid doesn't indicate +## support for them. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use EDID provided values (Default) +## 1 Pretend 3D mode is supported +## +#hdmi_force_edid_3d=1 + +## avoid_edid_fuzzy_match +## Avoid fuzzy matching of modes described in edid. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use fuzzy matching (Default) +## 1 Avoid fuzzy matching +## +#avoid_edid_fuzzy_match=1 + +## hdmi_pixel_encoding +## Force the pixel encoding mode. +## By default it will use the mode requested from edid so shouldn't +## need changing. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use EDID provided values (Default) +## 1 RGB limited (16-235) +## 2 RGB full ( 0-255) +## 3 YCbCr limited (16-235) +## 4 YCbCr limited ( 0-255) +## +#hdmi_pixel_encoding=1 + +## hdmi_group +## Defines the HDMI type +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Use the preferred group reported by the edid (Default) +## 1 CEA +## 2 DMT +## +#hdmi_group=1 + +## hdmi_mode +## defines screen resolution in CEA or DMT format +## +## H means 16:9 variant (of a normally 4:3 mode). +## 2x means pixel doubled (i.e. higher clock rate, with each pixel repeated +## twice) +## 4x means pixel quadrupled (i.e. higher clock rate, with each pixel +## repeated four times) +## reduced blanking means fewer bytes are used for blanking within the data +## stream (i.e. lower clock rate, with fewer wasted bytes) +## +## Value hdmi_group=CEA hdmi_group=DMT +## ------------------------------------------------------------------------- +## 1 VGA 640x350 85Hz +## 2 480p 60Hz 640x400 85Hz +## 3 480p 60Hz H 720x400 85Hz +## 4 720p 60Hz 640x480 60Hz +## 5 1080i 60Hz 640x480 72Hz +## 6 480i 60Hz 640x480 75Hz +## 7 480i 60Hz H 640x480 85Hz +## 8 240p 60Hz 800x600 56Hz +## 9 240p 60Hz H 800x600 60Hz +## 10 480i 60Hz 4x 800x600 72Hz +## 11 480i 60Hz 4x H 800x600 75Hz +## 12 240p 60Hz 4x 800x600 85Hz +## 13 240p 60Hz 4x H 800x600 120Hz +## 14 480p 60Hz 2x 848x480 60Hz +## 15 480p 60Hz 2x H 1024x768 43Hz DO NOT USE +## 16 1080p 60Hz 1024x768 60Hz +## 17 576p 50Hz 1024x768 70Hz +## 18 576p 50Hz H 1024x768 75Hz +## 19 720p 50Hz 1024x768 85Hz +## 20 1080i 50Hz 1024x768 120Hz +## 21 576i 50Hz 1152x864 75Hz +## 22 576i 50Hz H 1280x768 reduced blanking +## 23 288p 50Hz 1280x768 60Hz +## 24 288p 50Hz H 1280x768 75Hz +## 25 576i 50Hz 4x 1280x768 85Hz +## 26 576i 50Hz 4x H 1280x768 120Hz reduced blanking +## 27 288p 50Hz 4x 1280x800 reduced blanking +## 28 288p 50Hz 4x H 1280x800 60Hz +## 29 576p 50Hz 2x 1280x800 75Hz +## 30 576p 50Hz 2x H 1280x800 85Hz +## 31 1080p 50Hz 1280x800 120Hz reduced blanking +## 32 1080p 24Hz 1280x960 60Hz +## 33 1080p 25Hz 1280x960 85Hz +## 34 1080p 30Hz 1280x960 120Hz reduced blanking +## 35 480p 60Hz 4x 1280x1024 60Hz +## 36 480p 60Hz 4x H 1280x1024 75Hz +## 37 576p 50Hz 4x 1280x1024 85Hz +## 38 576p 50Hz 4x H 1280x1024 120Hz reduced blanking +## 39 1080i 50Hz reduced blanking 1360x768 60Hz +## 40 1080i 100Hz 1360x768 120Hz reduced blanking +## 41 720p 100Hz 1400x1050 reduced blanking +## 42 576p 100Hz 1400x1050 60Hz +## 43 576p 100Hz H 1400x1050 75Hz +## 44 576i 100Hz 1400x1050 85Hz +## 45 576i 100Hz H 1400x1050 120Hz reduced blanking +## 46 1080i 120Hz 1440x900 reduced blanking +## 47 720p 120Hz 1440x900 60Hz +## 48 480p 120Hz 1440x900 75Hz +## 49 480p 120Hz H 1440x900 85Hz +## 50 480i 120Hz 1440x900 120Hz reduced blanking +## 51 480i 120Hz H 1600x1200 60Hz +## 52 576p 200Hz 1600x1200 65Hz +## 53 576p 200Hz H 1600x1200 70Hz +## 54 576i 200Hz 1600x1200 75Hz +## 55 576i 200Hz H 1600x1200 85Hz +## 56 480p 240Hz 1600x1200 120Hz reduced blanking +## 57 480p 240Hz H 1680x1050 reduced blanking +## 58 480i 240Hz 1680x1050 60Hz +## 59 480i 240Hz H 1680x1050 75Hz +## 60 1680x1050 85Hz +## 61 1680x1050 120Hz reduced blanking +## 62 1792x1344 60Hz +## 63 1792x1344 75Hz +## 64 1792x1344 120Hz reduced blanking +## 65 1856x1392 60Hz +## 66 1856x1392 75Hz +## 67 1856x1392 120Hz reduced blanking +## 68 1920x1200 reduced blanking +## 69 1920x1200 60Hz +## 70 1920x1200 75Hz +## 71 1920x1200 85Hz +## 72 1920x1200 120Hz reduced blanking +## 73 1920x1440 60Hz +## 74 1920x1440 75Hz +## 75 1920x1440 120Hz reduced blanking +## 76 2560x1600 reduced blanking +## 77 2560x1600 60Hz +## 78 2560x1600 75Hz +## 79 2560x1600 85Hz +## 80 2560x1600 120Hz reduced blanking +## 81 1366x768 60Hz +## 82 1080p 60Hz +## 83 1600x900 reduced blanking +## 84 2048x1152 reduced blanking +## 85 720p 60Hz +## 86 1366x768 reduced blanking +## +#hdmi_mode=1 + +## config_hdmi_boost +## configure the signal strength of the HDMI interface. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 (Default) +## 1 +## 2 +## 3 +## 4 Try if you have interference issues with HDMI +## 5 +## 6 +## 7 Maximum +## +#config_hdmi_boost=0 + +## hdmi_ignore_cec_init +## Doesn't sent initial active source message. Avoids bringing +## (CEC enabled) TV out of standby and channel switch when rebooting. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Normal behaviour (Default) +## 1 Doesn't sent initial active source message +## +#hdmi_ignore_cec_init=1 + +## hdmi_ignore_cec +## Pretends CEC is not supported at all by TV. +## No CEC functions will be supported. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Normal behaviour (Default) +## 1 Pretend CEC is not supported by TV +## +#hdmi_ignore_cec=1 + +################################################################################ +## Overscan Video Settings +################################################################################ + +## overscan_left +## Number of pixels to skip on left +## +#overscan_left=0 + +## overscan_right +## Number of pixels to skip on right +## +#overscan_right=0 + +## overscan_top +## Number of pixels to skip on top +## +#overscan_top=0 + +## overscan_bottom +## Number of pixels to skip on bottom +## +#overscan_bottom=0 + +## disable_overscan +## Set to 1 to disable overscan +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Overscan Enabled (Default) +## 1 Overscan Disabled +## +#disable_overscan=1 + +################################################################################ +## Framebuffer Video Settings +################################################################################ + +## framebuffer_width +## Console framebuffer width in pixels. Default is display width minus +## overscan. +## +#framebuffer_width=0 + +## framebuffer_height +## Console framebuffer height in pixels. Default is display height minus +## overscan. +## +#framebuffer_height=0 + +## framebuffer_depth +## Console framebuffer depth in bits per pixel. +## +## Value Description +## ------------------------------------------------------------------------- +## 8 Valid, but default RGB palette makes an unreadable screen +## 16 (Default) +## 24 Looks better but has corruption issues as of 2012/06/15 +## 32 Has no corruption issues but needs framebuffer_ignore_alpha=1 +## and shows the wrong colors as of 2012/06/15 +## +#framebuffer_depth=16 + +## framebuffer_ignore_alpha +## Set to 1 to disable alpha channel. Helps with 32bit. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Enable Alpha Channel (Default) +## 1 Disable Alpha Channel +## +#framebuffer_ignore_alpha=0 + +################################################################################ +## General Video Settings +################################################################################ + +## display_rotate +## Rotate the display clockwise or flip the display. +## The 90 and 270 degrees rotation options require additional memory on GPU, +## so won't work with the 16M GPU split. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 0 degrees (Default) +## 1 90 degrees +## 2 180 degrees +## 3 270 degrees +## 0x10000 Horizontal flip +## 0x20000 Vertical flip +## +#display_rotate=0 + +## dispmanx_offline +## Set to "1" to enable offline compositing +## +## Default 0 +## +#dispmanx_offline=0 + +################################################################################ +## Licensed Codecs +## +## Hardware decoding of additional codecs can be enabled by purchasing a +## license that is locked to the CPU serial number of your Raspberry Pi. +## +## Up to 8 licenses per CODEC can be specified as a comma seperated list. +## +################################################################################ + +## decode_MPG2 +## License key to allow hardware MPEG-2 decoding. +## +#decode_MPG2=0x12345678 + +## decode_WVC1 +## License key to allow hardware VC-1 decoding. +## +#decode_WVC1=0x12345678 + +################################################################################ +## Camera Settings +################################################################################ + +## start_x +## Set to "1" to enable the camera module. +## +## Enabling the camera requires gpu_mem option to be specified with a value +## of at least 128. +## +## Default 0 +## +#start_x=0 + +## disable_camera_led +## Turn off the red camera led when recording video or taking a still +## picture. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 LED enabled (Default) +## 1 LED disabled +## +#disable_camera_led=1 + +################################################################################ +## Test Settings +################################################################################ + +## test_mode +## Enable test sound/image during boot for manufacturing test. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Disable Test Mod (Default) +## 1 Enable Test Mode +## +#test_mode=0 + +################################################################################ +## Memory Settings +################################################################################ + +## disable_l2cache +## Disable arm access to GPU's L2 cache. Needs corresponding L2 disabled +## kernel. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Enable L2 Cache (Default) +## 1 Disable L2 cache +## +#disable_l2cache=0 + +## gpu_mem +## GPU memory allocation in MB for all board revisions. +## +## Default 64 +## +gpu_mem=128 + +## gpu_mem_256 +## GPU memory allocation in MB for 256MB board revision. +## This option overrides gpu_mem. +## +#gpu_mem_256=192 + +## gpu_mem_512 +## GPU memory allocation in MB for 512MB board revision. +## This option overrides gpu_mem. +## +#gpu_mem_512=448 + +## gpu_mem_1024 +## GPU memory allocation in MB for 1024MB board revision. +## This option overrides gpu_mem. +## +#gpu_mem_1024=944 + +## disable_pvt +## Disable adjusting the refresh rate of RAM every 500ms +## (measuring RAM temparature). +## +#disable_pvt=1 + +################################################################################ +## CMA - Dynamic Memory Split +## +## CMA enables dynamic management of the ARM and GPU memory split at runtime. +## +## The following options need to be in cmdline.txt for CMA to work: +## coherent_pool=6M smsc95xx.turbo_mode=N +## +################################################################################ + +## cma_lwm +## When GPU has less than cma_lwm (low water mark) memory available it +## will request some from ARM. +## +#cma_lwm=16 + +## cma_hwm +## When GPU has more than cma_hwm (high water mark) memory available it +## will release some to ARM. +## +#cma_hwm=32 + +################################################################################ +## Boot Option Settings +################################################################################ + +## disable_commandline_tags +## Stop start.elf from filling in ATAGS (memory from 0x100) before +## launching kernel +## +#disable_commandline_tags=0 + +## cmdline (string) +## Command line parameters. Can be used instead of cmdline.txt file +## +#cmdline="" + +## kernel (string) +## Alternative name to use when loading kernel. +## +#kernel="" + +## kernel_address +## Address to load kernel.img file at +## +#kernel_address=0x00000000 + +## kernel_old +## Support loading old kernels +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Disabled (Default) +## 1 Load kernel at address 0x00000000 +## +#kernel_old=1 + +## ramfsfile (string) +## ramfs file to load +## +#ramfsfile="" + +## ramfsaddr +## Address to load ramfs file at +## +#ramfsaddr=0x00000000 + +## initramfs (string address) +## ramfs file and address to load it at (it's like ramfsfile+ramfsaddr in +## one option). +## +## NOTE: this option uses different syntax than all other options - you +## should not use "=" character here. +## +#initramfs initramf.gz 0x00800000 + +## device_tree_address +## Address to load device_tree at +## +#device_tree_address=0x00000000 + +## init_uart_baud +## Initial uart baud rate. +## +## Default 115200 +## +#init_uart_baud=115200 + +## init_uart_clock +## Initial uart clock. +## +## Default 3000000 (3MHz) +## +#init_uart_clock=3000000 + +## init_emmc_clock +## Initial emmc clock, increasing this can speedup your SD-card. +## +## Default 100000000 (100mhz) +## +#init_emmc_clock=100000000 + +## boot_delay +## Wait for a given number of seconds in start.elf before loading +## kernel.img. +## +## delay = (1000 * boot_delay) + boot_delay_ms +## +## Default 1 +## +#boot_delay=0 + +## boot_delay_ms +## Wait for a given number of milliseconds in start.elf before loading +## kernel.img. +## +## delay = (1000 * boot_delay) + boot_delay_ms +## +## Default 0 +## +#boot_delay_ms=0 + +## avoid_safe_mode +## Adding a jumper between pins 5 & 6 of P1 enables a recovery Safe Mode. +## If pins 5 & 6 are used for connecting to external devices (e.g. GPIO), +## then this setting can be used to ensure Safe Mode is not triggered. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Respect Safe Mode input (Default) +## 1 Ignore Safe Mode input +## +#avoid_safe_mode=1 + +## disable_splash +## Avoids the rainbow splash screen on boot. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Splash screen enabled (Default) +## 1 Splash screen disabled +## +#disable_splash=1 + +################################################################################ +## Overclocking Settings +## +## ARM, SDRAM and GPU each have their own PLLs and can have unrelated +## frequencies. +## +## The GPU core, h264, v3d and isp share a PLL, so need to have related +## frequencies. +## pll_freq = floor(2400 / (2 * core_freq)) * (2 * core_freq) +## gpu_freq = pll_freq / [even number] +## +## The effective gpu_freq is automatically rounded to nearest even integer, so +## asking for core_freq = 500 and gpu_freq = 300 will result in divisor of +## 2000/300 = 6.666 => 6 and so 333.33MHz. +## +## +## Standard Profiles: +## arm_freq core_freq sdram_freq over_voltage +## ------------------------------------------------------------------------- +## None 700 250 400 0 +## Modest 800 300 400 0 +## Medium 900 333 450 2 +## High 950 450 450 6 +## Turbo 1000 500 500 6 +## +################################################################################ + +## force_turbo +## Control the kernel "ondemand" governor. It has no effect if no overclock +## settings are specified. +## May set warrany bit. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Enable dynamic clocks and voltage for the ARM core, GPU core and +## SDRAM (Default). +## Overclocking of h264_freq, v3d_freq and isp_freq is ignored. +## 1 Disable dynamic clocks and voltage for the ARM core, GPU core +## and SDRAM. +## Overclocking of h264_freq, v3d_freq and isp_freq is allowed. +## +#force_turbo=0 + +## initial_turbo +## Enables turbo mode from boot for the given value in seconds (up to 60) +## or until cpufreq sets a frequency. Can help with sdcard corruption if +## overclocked. +## +## Default 0 +## +#initial_turbo=0 + +## temp_limit +## Overheat protection. Sets clocks and voltages to default when the SoC +## reaches this Celsius value. +## Setting this higher than default voids warranty. +## +## Default 85 +## +#temp_limit=85 + +## arm_freq +## Frequency of ARM in MHz. +## +## Default 700. +## +arm_freq=900 + +## arm_freq_min +## Minimum frequency of ARM in MHz (used for dynamic clocking). +## +## Default 700. +## +#arm_freq_min=700 + +## gpu_freq +## Sets core_freq, h264_freq, isp_freq, v3d_freq together. +## +## Default 250. +## +#gpu_freq=250 + +## core_freq +## Frequency of GPU processor core in MHz. It has an impact on ARM +## performance since it drives L2 cache. +## +## Default 250. +## +#core_freq=250 + +## core_freq_min +## Minimum frequency of GPU processor core in MHz (used for dynamic +## clocking). It has an impact on ARM performance since it drives L2 cache. +## +## Default 250. +## +#core_freq_min=250 + +## h264_freq +## Frequency of hardware video block in MHz. +## +## Default 250. +## +#h264_freq=250 + +## isp_freq +## Frequency of image sensor pipeline block in MHz. +## +## Default 250. +## +#isp_freq=250 + +## v3d_freq +## Frequency of 3D block in MHz. +## +## Default 250. +## +#v3d_freq=250 + +## sdram_freq +## Frequency of SDRAM in MHz. +## +## Default 400. +## +#sdram_freq=400 + +## sdram_freq_min +## Minimum frequency of SDRAM in MHz (used for dynamic clocking). +## +## Default 400. +## +#sdram_freq_min=400 + +## avoid_pwm_pll +## Don't dedicate a pll to PWM audio. This will reduce analogue audio +## quality slightly. The spare PLL allows the core_freq to be set +## independently from the rest of the gpu allowing more control over +## overclocking. +## +## Value Description +## ------------------------------------------------------------------------- +## 0 Linked core_freq (Default) +## 1 Unlinked core_freq +## +#avoid_pwm_pll=1 + +################################################################################ +## Voltage Settings +################################################################################ + +## current_limit_override +## Disables SMPS current limit protection. Can help if you are currently +## hitting a reboot failure when overclocking too high. +## May set warrany bit. +## +#current_limit_override=0x5A000020 + +## over_voltage +## ARM/GPU core voltage adjust. +## May set warrany bit. +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V (requires force_turbo=1 or current_limit_override) +## 8 1.4 V (requires force_turbo=1 or current_limit_override) +## +#over_voltage=0 + +## over_voltage_min +## Minimum ARM/GPU core voltage adjust (used for dynamic clocking). +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V (requires force_turbo=1) +## 8 1.4 V (requires force_turbo=1) +## +#over_voltage_min=0 + +## over_voltage_sdram +## Sets over_voltage_sdram_c, over_voltage_sdram_i, over_voltage_sdram_p +## together +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V +## 8 1.4 V +## +#over_voltage_sdram=0 + +## over_voltage_sdram_c +## SDRAM controller voltage adjust. +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V +## 8 1.4 V +## +#over_voltage_sdram_c=0 + +## over_voltage_sdram_i +## SDRAM I/O voltage adjust. +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V +## 8 1.4 V +## +#over_voltage_sdram_i=0 + +## over_voltage_sdram_p +## SDRAM phy voltage adjust. +## +## Value Description +## ------------------------------------------------------------------------- +## -16 0.8 V +## -15 0.825 V +## -14 0.85 V +## -13 0.875 V +## -12 0.9 V +## -11 0.925 V +## -10 0.95 V +## -9 0.975 V +## -8 1.0 V +## -7 1.025 V +## -6 1.05 V +## -5 1.075 V +## -4 1.1 V +## -3 1.125 V +## -2 1.15 V +## -1 1.175 V +## 0 1.2 V (Default) +## 1 1.225 V +## 2 1.25 V +## 3 1.275 V +## 4 1.3 V +## 5 1.325 V +## 6 1.35 V +## 7 1.375 V +## 8 1.4 V +## +#over_voltage_sdram_p=0 + +################################################################################ +## USB Power +################################################################################ + +## max_usb_current +## When set to 1, change the output current limit (for all 4 USB +## ports combined) from 600mA to double that, 1200mA. +## +## This option is not available for Model A/B boards. +## +## Default 0. +## +#max_usb_current=0 + +################################################################################ +## Base Device Tree Parameters +################################################################################ + +## audio +## Enable the onboard ALSA audio +## +## Default off. +## +dtparam=audio=on + +## i2c_arm +## Enable the ARM's i2c interface +## +## Default off. +## +#dtparam=i2c_arm=off + +## i2c_vc +## Enable the i2c interface +## +## Usually reserved for the VideoCore processor +## +## Default off. +## +#dtparam=i2c_vc=off + +## i2c_arm_baudrate +## Set the baudrate of the ARM's i2c interface +## +## Default 100000. +## +#dtparam=i2c_arm_baudrate=100000 + +## i2c_vc_baudrate +## Set the baudrate of the VideoCore i2c interface +## +## Default 100000. +## +#dtparam=i2c_vc_baudrate=100000 + +## i2s +## Set to "on" to enable the i2s interface +## +## Default off. +## +#dtparam=i2s=off + +## spi +## Set to "on" to enable the spi interfaces +## +## Default off. +## +#dtparam=spi=off + +## random +## Set to "on" to enable the hardware random +## +## Default off. +## +#dtparam=random=off + +## uart0 +## Set to "off" to disable uart0 +## +## Default on. +## +#dtparam=uart0=on + +## watchdog +## Set to "on" to enable the hardware watchdog +## +## Default off. +## +#dtparam=watchdog=off + +## act_led_trigger +## Choose which activity the LED tracks. +## +## Use "heartbeat" for a nice load indicator. +## +## Default mmc. +## +#dtparam=act_led_trigger=mmc + +## act_led_activelow +## Set to "on" to invert the sense of the LED +## +## Default off. +## +#dtparam=act_led_activelow=off + +## act_led_gpio +## Set which GPIO to use for the activity LED +## +## In case you want to connect it to an external device +## +## Default 16 on a non-Plus board, 47 on a Plus or Pi 2. +## +#dtparam=act_led_gpio=47 + +## pwr_led_trigger +## Choose which activity the LED tracks. +## +## Use "heartbeat" for a nice load indicator. +## +## Not available on Model A/B boards. +## +## Default mmc. +## +#dtparam=pwr_led_trigger=mmc + +## pwr_led_activelow +## Set to "on" to invert the sense of the LED +## +## Not available on Model A/B boards. +## +## Default off. +## +#dtparam=pwr_led_activelow=off + +## pwr_led_gpio +## Set which GPIO to use for the PWR LED +## +## In case you want to connect it to an external device +## +## Not available on Model A/B boards. +## +## Default 35. +## +#dtparam=pwr_led_gpio=35 diff --git a/rpi2/extlinux.conf b/rpi2/extlinux.conf new file mode 100644 index 0000000..91a46a2 --- /dev/null +++ b/rpi2/extlinux.conf @@ -0,0 +1,10 @@ +menu Welcome to Mageia-Minimal. +timeout 20 +default Mageia + +label Mageia + kernel /boot/vmlinuz + append root=UUID=<UUID> dwc_otg.lpm_enable=0 console=ttyS0,115200 kgdboc=ttyS0,115200 console=tty1 rootwait fsck.repair=1 8250.nr_uarts=1 elevator=deadline cma=256M\@512M audit=0 + fdtdir /usr/lib/<FDTDIR> + initrd /boot/initrd + diff --git a/rpi2/mageia4arm.cfg b/rpi2/mageia4arm.cfg new file mode 100644 index 0000000..1b28d6e --- /dev/null +++ b/rpi2/mageia4arm.cfg @@ -0,0 +1,60 @@ + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot <contact@librepc.com> +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + + +MAGEIA_VERSION="6" +ARM_VERSION="armv7hl" + +#target plateform (xu3-4 or rpi) +TARGET="rpi" +#version of the target +# 0, 1, 2 ,3_32 for rpi and 3 or 4 for odroid +TARGET_VERSION="2" + +# URL of the Mageia mirror used to install ( see mirrors.mageia.org ) +MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +#MIRROR="/mnt/STOCK/mageia/distrib/$MAGEIA_VERSION/$ARM_VERSION" +# image will be created here + +INSTALL_PATH="/mnt/perso/raspi2" + +# Build directory will be created here +BUILD_PATH="$INSTALL_PATH/build" + +#name of the image +IMAGE="Mageia-${MAGEIA_VERSION}-$TARGET$TARGET_VERSION.img" + +#Mount point of image's partitions +BOOT="/mnt/boot" +ROOT="/mnt/root" + +#Default user +ID_USER="pi" +PASSWORD="raspberry" + +#root password +ROOT_PWD="piroot" + +#Hostname +HOSTNAME="$TARGET.$ID_USER" + +#Filesystem of boot partitions (default ext4 raspberry pi need vfat) +BOOTFS="vfat" + +#Path where the raspberry pi firmware is/will be installed +FIRMWARE_PATH="$INSTALL_PATH" +FIRMWARE_DIR="firmware-stable" +FIRMWARE_DOWNLOAD_URL="https://github.com/raspberrypi/firmware/archive/stable.zip" diff --git a/rpi2/mageia4arm.cfg.original b/rpi2/mageia4arm.cfg.original new file mode 100644 index 0000000..ae56885 --- /dev/null +++ b/rpi2/mageia4arm.cfg.original @@ -0,0 +1,59 @@ + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot <dtux@free.fr> +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + + +MAGEIA_VERSION="7" +ARM_VERSION="armv7hl" + +#target plateform (xu3-4 or rpi) +TARGET="rpi" +#version of the target +# 0, 1, 2 ,3_32 for rpi and 3 or 4 for odroid +TARGET_VERSION="3_32" + +# URL of the Mageia mirror used to install ( see mirrors.mageia.org ) +MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +# image will be created here +INSTALL_PATH="<change this>" + +# Build directory will be created here +BUILD_PATH="$INSTALL_PATH/build" + +#name of the image +IMAGE="Mageia-${MAGEIA_VERSION}-$TARGET.img" + +#Mount point of image's partitions +#no need to be changed +BOOT="/mnt/boot" +ROOT="/mnt/root" + +#Default user +ID_USER="pi" +PASSWORD="raspberry" + +#root password +ROOT_PWD="piroot" + +#Hostname +HOSTNAME="$TARGET.$ID_USER" + +#Filesystem of boot partitions (default ext4 raspberry pi need vfat) +#DO NOT CHANGE THIS +BOOTFS="vfat" + +#Path where the raspberry pi firmware is/will be installed +FIRMWARE_PATH="$INSTALL_PATH" +FIRMWARE_DIR="firmware-stable" diff --git a/rpi2/mageia4arm.cfg~ b/rpi2/mageia4arm.cfg~ new file mode 100644 index 0000000..e093329 --- /dev/null +++ b/rpi2/mageia4arm.cfg~ @@ -0,0 +1,57 @@ + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot <contact@librepc.com> +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + + +MAGEIA_VERSION="7" +ARM_VERSION="armv7hl" + +#target plateform (xu3-4 or rpi) +TARGET="rpi" +TARGET_VERSION="3" + +# URL of the Mageia mirror used to install ( see mirrors.mageia.org ) +MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +#MIRROR="/mnt/STOCK/mageia/distrib/$MAGEIA_VERSION/$ARM_VERSION" +# image will be created here + +INSTALL_PATH="/mnt/perso/raspi-test" + +# Build directory will be created here +BUILD_PATH="$INSTALL_PATH/build" + +#name of the image +IMAGE="Mageia-${MAGEIA_VERSION}-$TARGET.img" + +#Mount point of image's partitions +BOOT="/mnt/boot" +ROOT="/mnt/root" + +#Default user +ID_USER="pi" +PASSWORD="raspberry" + +#root password +ROOT_PWD="piroot" + +#Hostname +HOSTNAME="$TARGET.$ID_USER" + +#Filesystem of boot partitions (default ext4 raspberry pi need vfat) +BOOTFS="vfat" + +#Path where the raspberry pi firmware is/will be installed +FIRMWARE_PATH="$INSTALL_PATH" +FIRMWARE_DIR="firmware-stable" diff --git a/rpi2/modprobe.conf b/rpi2/modprobe.conf new file mode 100644 index 0000000..7725dae --- /dev/null +++ b/rpi2/modprobe.conf @@ -0,0 +1,3 @@ +alias wlan0 brcmfmac +alias eth0 smsc95xx +alias usb0 rndis_host diff --git a/rpi2/second_stage_install.sh b/rpi2/second_stage_install.sh new file mode 100644 index 0000000..1848789 --- /dev/null +++ b/rpi2/second_stage_install.sh @@ -0,0 +1,41 @@ +#!/bin/bash + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot <contact@librepc.com> +# + +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + +/usr/bin/chown :shadow /etc/shadow /etc/gshadow /etc/login.defs /etc/pam.d/chage-chfn-chsh /etc/pam.d/chpasswd-newusers /etc/pam.d/system-auth /etc/pam.d/user-group-mod /bin/passwd /bin/chage + +/usr/bin/chown :systemd-journal -R /var/log/journal + +#Install all packages you need +# No verifying rpm due to a bug in packages, some are not signed + +/usr/sbin/urpmi --auto --no-verify-rpm basesystem chrony rng-tools man openssh-server rfkill wireless-tools bluez wpa_supplicant make binutils dracut u-boot rsync kernel-desktop-latest mlocate drakx-kbd-mouse-x11 + + +/usr/bin/chown :chrony -R /etc/chrony.keys /var/log/chrony +/usr/bin/chown :daemon /etc/wpa_supplicant.conf +/usr/bin/chown :tty /bin/write /bin/wall +/usr/bin/chown :lock /sbin/lockdev +/usr/bin/chown :bin /sbin/traceroute +/usr/bin/chown polkitd /etc/polkit-1/rules.d + +KV=`basename /boot/vmlinuz-*` +KV=${KV#vmlinuz-} +dracut --kver $KV +rm -f $0 +cp /boot/vmlinuz-* /boot/vmlinuz +cp /boot/initrd-* /boot/initrd diff --git a/rpi3+/mageia4arm.cfg b/rpi3+/mageia4arm.cfg new file mode 100644 index 0000000..f4dd78d --- /dev/null +++ b/rpi3+/mageia4arm.cfg @@ -0,0 +1,61 @@ + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot <contact@librepc.com> +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. + + +MAGEIA_VERSION="7" +ARM_VERSION="armv7hl" + +#target plateform (xu3-4 or rpi) +TARGET="rpi" +#version of the target +# 0, 1, 2 ,3_32 for rpi and 3 or 4 for odroid +TARGET_VERSION="3+" + +# URL of the Mageia mirror used to install ( see mirrors.mageia.org ) +MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +#MIRROR="/mnt/STOCK/mageia/distrib/$MAGEIA_VERSION/$ARM_VERSION" +# image will be created here + +INSTALL_PATH="/mnt/perso/raspi-test" + +# Build directory will be created here +BUILD_PATH="$INSTALL_PATH/build" + +#name of the image +IMAGE="Mageia-${MAGEIA_VERSION}-$TARGET.img" + +#Mount point of image's partitions +BOOT="/mnt/boot" +ROOT="/mnt/root" + +#Default user +ID_USER="pi" +PASSWORD="raspberry" + +#root password +ROOT_PWD="piroot" + +#Hostname +HOSTNAME="$TARGET.$ID_USER" + +#Filesystem of boot partitions (default ext4 raspberry pi need vfat) +BOOTFS="vfat" + +#Path where the raspberry pi firmware is/will be installed +FIRMWARE_PATH="$INSTALL_PATH" +FIRMWARE_DIR="firmware-stable" +FIRMWARE_DOWNLOAD_URL="https://github.com/raspberrypi/firmware/archive/stable.zip" + diff --git a/xu4/mageia4arm.cfg b/xu4/mageia4arm.cfg index adb98cd..3d7d025 100644 --- a/xu4/mageia4arm.cfg +++ b/xu4/mageia4arm.cfg @@ -15,14 +15,14 @@ # along with this program. If not, see <http://www.gnu.org/licenses/>. -MAGEIA_VERSION="cauldron" +MAGEIA_VERSION="7" ARM_VERSION="armv7hl" TARGET="odroid" TARGET_VERSION="xu4" # URL of the Mageia mirror used to install ( see mirrors.mageia.org ) -MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" - +#MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +MIRROR="http://192.168.1.252/mageia/distrib/$MAGEIA_VERSION/$ARM_VERSION" # image will be created here INSTALL_PATH="/mnt/perso/xu4-test/" |