#!/bin/sh
#
# init.ipv6-global
#
#
# Taken from:
# (P) & (C) 2001 by Peter Bieringer <pb@bieringer.de>
#
# RHL integration assistance by Pekka Savola <pekkas@netcore.fi>
#
# Version 2001-05-22d
#
# Calling parameters:
#  $1: action (currently supported: start|stop|showsysctl)
#  $2: position for start|stop (currently supported: pre|post)
#
# Called by hooks from /etc/rc.d/init.d/network
#
# Uses following information from /etc/sysconfig/network:
#  NETWORKING_IPV6=yes|no: controls global IPv6 initialization (default: no)
#  IPV6FORWARDING=yes|no: controls global IPv6 forwarding (default: no)
#  IPV6AUTOCONF=yes|no: controls global automatic IPv6 configuration
#   (default: yes if IPV6FORWARDING=no, no if IPV6FORWARDING=yes)
#  IPV6_AUTOTUNNEL=yes|no: controls automatic IPv6 tunneling (default: no)
#



# Get global network configuration
. /etc/sysconfig/network 

# Source IPv4 helper functions
cd /etc/sysconfig/network-scripts
. network-functions 

# Get action and hook position
ACTION="$1"
POSITION="$2"

# Test for IPv6 enabling
if [ ! "${NETWORKING_IPV6}" = "yes" ]; then
	exit 0
fi

if [ ! -f /etc/sysconfig/network-scripts/network-functions-ipv6 ]; then
	exit 1
fi

# Source IPv6 helper functions
. /etc/sysconfig/network-scripts/network-functions-ipv6

# Initialize IPv6, depending on caller option
case $ACTION in
    start)
	case $POSITION in 
	    pre)
		# IPv6 test, module loaded, exit if system is not IPv6-ready
		test_ipv6 || exit 1


		if [ "$IPV6FORWARDING" = "yes" ]; then
			ipv6_global_forwarding=1
			ipv6_global_auto=0
		else
			ipv6_global_forwarding=0
			if [ "$IPV6AUTO" = "no" ]; then
				ipv6_global_auto=0
			else
				ipv6_global_auto=1
			fi
		fi

		# Reset IPv6 sysctl switches for "all", "default" and still existing devices
		for i in /proc/sys/net/ipv6/conf/*; do
			if [ ! -d $i ]; then
				continue
			fi
			interface="`echo $i | awk -F/ '{ print $NF}'`"
			# Host/Router behaviour for the interface
			sysctl -w net.ipv6.conf.$interface.forwarding=$ipv6_global_forwarding >/dev/null

			# Autoconfiguration and redirect handling for Hosts
			sysctl -w net.ipv6.conf.$interface.accept_ra=$ipv6_global_auto >/dev/null
			sysctl -w net.ipv6.conf.$interface.accept_redirects=$ipv6_global_auto >/dev/null
		done

		if [ "$IPV6_AUTOTUNNEL" = "yes" ]; then
			ifup_ipv6_autotunnel 
		fi
		;;

	    post)
		# IPv6 test, module loaded, exit if system is not IPv6-ready
		test_ipv6 || exit 1


		## Add some routes which should never appear on the wire
		# Unreachable IPv4-only addresses, normally blocked by source address selection
		ip route add unreach  ::ffff:0.0.0.0/96
		# Unreachable IPv4-mapped addresses
		ip route add unreach  ::0.0.0.0/96
		# Unreachable 6to4: IPv4 multicast, reserved, limited broadcast
		ip route add unreach  2002:e000::/19
		# Unreachable 6to4: IPv4 loopback
		ip route add unreach  2002:7f00::/24
		# Unreachable 6to4: IPv4 private (RFC1918)
		ip route add unreach  2002:0a00::/24
		ip route add unreach  2002:ac10::/28
		ip route add unreach  2002:c0a8::/32
		# Unreachable 6to4: IPv4 private (DHCP link-local)
		ip route add unreach  2002:a9fe::/32
		;;

	    *)
		echo "Usage: $0 $1 {pre|post}"
		;;

	esac
	;;

    stop)
	case $POSITION in 
	    pre)
		# IPv6 test, no module loaded, exit if system is not IPv6-ready
		test_ipv6 testonly || exit 0


		;;

	    post)
		# IPv6 test, no module loaded, exit if system is not IPv6-ready
		test_ipv6 testonly || exit 0


		for i in /proc/sys/net/ipv6/conf/*; do
			if [ ! -d $i ]; then
				continue
			fi
			interface="`echo $i | awk -F/ '{ print $NF}'`"
			# Assume Host behaviour
			sysctl -w net.ipv6.conf.$interface.forwarding=0 >/dev/null  

			# Disable autoconfiguration and redirects
			sysctl -w net.ipv6.conf.$interface.accept_ra=0 >/dev/null  
			sysctl -w net.ipv6.conf.$interface.accept_redirects=0 >/dev/null  
		done

		# Find still existing tunnel devices and shutdown and delete them
		LC_ALL=C ip tunnel | grep "ipv6/ip" | awk -F: '{ print $1 }' | while read device; do
			ifdown_ipv6_tunneldev $device
		done

		;;

	    *)
		echo "Usage: $0 $1 {pre|post}"
		;;

	esac	
	;;

    restart|reload)
	# do nothing, will be handled by main script
	;;

    showsysctl)
	# Run only basic tests, no module is loaded, if not ok, skip IPv6 initialization
	test_ipv6 testonly || exit 0

	# Show sysctl switches 
	for i in /proc/sys/net/ipv6/conf/default/*; do
		if [ ! -f $i ]; then continue; fi
		switch="`echo $i | awk -F/ '{ print $NF}'`"
		for j in /proc/sys/net/ipv6/conf/*; do
			if [ ! -d $j ]; then continue; fi
			interface="`echo $j | awk -F/ '{ print $NF}'`"
			sysctl net.ipv6.conf.$interface.$switch
		done
		echo
	done
	;;

    *)
	echo "Usage: $0 {start|stop|showsysctl}"
	exit 1
	;;	

esac