#!/bin/bash
# Network Interface Configuration System
# Copyright (c) 1996-2005 Red Hat, Inc. all rights reserved.
#
# This software may be freely redistributed under the terms of the GNU
# public license.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

. /etc/init.d/functions

cd /etc/sysconfig/network-scripts
. network-functions

[ -f ../network ] && . ../network

CONFIG=${1}

need_config ${CONFIG}

source_config

# Old BOOTP variable
if [ "${BOOTP}" = "yes" ]; then
    BOOTPROTO=bootp
fi

if [ "${BOOTPROTO}" = "bootp" -o "${BOOTPROTO}" = "dhcp" ]; then
    DYNCONFIG=true
fi

# load the module associated with that device
# /sbin/modprobe ${REALDEVICE}
is_available ${REALDEVICE}

# remap, if the device is bound with a MAC address and not the right device num
# bail out, if the MAC does not fit
if [ -n "${HWADDR}" ]; then
    FOUNDMACADDR=`get_hwaddr ${REALDEVICE}`
    if [ "${FOUNDMACADDR}" != "${HWADDR}" ]; then
        curdev=`ip -o link | awk -F ':' -vIGNORECASE=1 "/$HWADDR/ { print \\$2 }"`
        if [ -n "$curdev" ]; then
	  rename_device "${REALDEVICE}" "${HWADDR}" "${curdev}" || {
	    echo $"Device ${DEVICE} has different MAC address than expected, ignoring."
	    exit 1
	  }
	fi
    fi
fi

if [ "${TYPE}" = "Bridge" ]; then
      if [ ! -x /usr/sbin/brctl ]; then
	  echo $"Bridge support not available: brctl not found"
	  exit 1
      fi
      /sbin/ip link set dev ${DEVICE} down 2>/dev/null
      /usr/sbin/brctl delbr ${DEVICE} 2>/dev/null
      /usr/sbin/brctl addbr ${DEVICE} 2>/dev/null
      # brctl doesn't report success/failure (BZ #104408)
      # Test for ourselves whether it worked.
      if ! /usr/sbin/brctl show | LANG=C grep -q "^${DEVICE}	" ; then
	    echo $"Bridge support not available in this kernel"
	    exit 1
      fi
      [ -n "${DELAY}" ] && /usr/sbin/brctl setfd ${DEVICE} ${DELAY}
      [ -n "${GCINT}" ] && /usr/sbin/brctl setgcint ${DEVICE} ${GCINT}
      [ -n "${STP}" ] && /usr/sbin/brctl stp ${DEVICE} ${STP}
fi

if [ -n "${BRIDGE}" -a -x /usr/sbin/brctl ]; then
      /sbin/ip addr flush dev ${DEVICE} 2>/dev/null
      /sbin/ip link set dev ${DEVICE} up
      /usr/sbin/brctl addif ${BRIDGE} ${DEVICE}
      # Upon adding a device to a bridge, 
      # it's necessary to make radvd reload its config
      [ -r /var/run/radvd/radvd.pid ] && kill -HUP `cat /var/run/radvd/radvd.pid`
      exit 0
fi 

# now check the real state
is_available ${REALDEVICE} || {
      if [ -n "$alias" ]; then
         echo $"$alias device ${DEVICE} does not seem to be present, delaying initialization."
      else
         echo $"Device ${DEVICE} does not seem to be present, delaying initialization."
      fi
      exit 1
}

# is the device wireless? If so, configure wireless device specifics
is_wireless_device ${DEVICE} && . ./ifup-wireless

# slave device?
if [ "${SLAVE}" = yes -a "${ISALIAS}" = no -a "${MASTER}" != "" -a \
     -x /sbin/ifenslave ]; then
    RFLAG="" ; [ "${RECEIVEONLY}" = yes ] && RFLAG="-r"

    /sbin/ip link set dev ${DEVICE} down
    echo $"Enslaving ${DEVICE} to ${MASTER}"
    ifenslave ${RFLAG} "${MASTER}" "${DEVICE}" >/dev/null 2>&1

    if [ -n "$ETHTOOL_OPTS" ] ; then
        /sbin/ethtool -s ${REALDEVICE} $ETHTOOL_OPTS
    fi

    exit 0
fi

# Bonding initialization. For DHCP, we need to enslave the devices early,
# so it can actually get an IP.
if [ "${TYPE}" =  "Bonding" ] || ethtool -i $DEVICE 2>/dev/null| grep -q "driver: bonding" ; then
    /sbin/ip link set dev ${DEVICE} down
    /sbin/ip link set dev ${DEVICE} up
    for device in `LANG=C grep -l "^[[:space:]]*MASTER=${DEVICE}" /etc/sysconfig/network-scripts/ifcfg-*` ; do
        if [ "$BOOTPROTO" = "dhcp" ]; then
		/sbin/ifup ${device##*/}
    	fi
    done
fi

# this isn't the same as the MAC in the configuration filename.  It is
# available as a configuration option in the config file, forcing the kernel
# to think an ethernet card has a different MAC address than it really has.
if [ -n "${MACADDR}" ]; then
   ip link set dev ${DEVICE} address ${MACADDR}
fi
if [ -n "${MTU}" ]; then
   ip link set dev ${DEVICE} mtu ${MTU}
fi

		     
if [ -n "${DYNCONFIG}" -a -x /sbin/dhclient ]; then
    # Remove any temporary references which were previously added to dhclient config
    if [ -w /etc/dhclient-${DEVICE}.conf ] ; then
        LC_ALL=C grep -v "# temporary RHL ifup addition" /etc/dhclient-${DEVICE}.conf > /etc/dhclient-${DEVICE}.conf.ifupnew 2> /dev/null
        cat /etc/dhclient-${DEVICE}.conf.ifupnew > /etc/dhclient-${DEVICE}.conf
        rm -f /etc/dhclient-${DEVICE}.conf.ifupnew
    fi
    if [[ "${PERSISTENT_DHCLIENT}" =  [yY1]* ]]; then
       ONESHOT="";
    else
       ONESHOT="-1";
    fi;
    if [ -n "${DHCP_HOSTNAME}" ]; then
       # Send a host-name to the DHCP server (requ. by some dhcp servers).
       if [ -w /etc/dhclient-${DEVICE}.conf ] ; then
           if ! LC_ALL=C grep "send *host-name *\"${DHCP_HOSTNAME}\"" /etc/dhclient-${DEVICE}.conf > /dev/null 2>&1 ; then
               echo "send host-name \"${DHCP_HOSTNAME}\";  # temporary RHL ifup addition" >> /etc/dhclient-${DEVICE}.conf
           fi
       elif ! [ -e /etc/dhclient-${DEVICE}.conf ] ; then
           echo "send host-name \"${DHCP_HOSTNAME}\";  # temporary RHL ifup addition" >> /etc/dhclient-${DEVICE}.conf
       fi
    fi
    # allow users to use generic '/etc/dhclient.conf' (as documented in manpage!) 
    # if per-device file doesn't exist or is empty
    if [ -s /etc/dhclient-${DEVICE}.conf ]; then
       DHCLIENTCONF="-cf /etc/dhclient-${DEVICE}.conf";
    else
       DHCLIENTCONF='';
    fi;
    DHCLIENTARGS="${DHCLIENTARGS} ${ONESHOT} -q ${DHCLIENTCONF} -lf /var/lib/dhcp/dhclient-${DEVICE}.leases -pf /var/run/dhclient-${DEVICE}.pid"
    echo
    echo -n $"Determining IP information for ${DEVICE}..."
    if check_link_down ${DEVICE}; then
	echo $" failed; no link present.  Check cable?"
	ip link set dev ${DEVICE} down >/dev/null 2>&1
	exit 1
    fi

    if [ -n "$ETHTOOL_OPTS" ] ; then
        /sbin/ethtool -s ${REALDEVICE} $ETHTOOL_OPTS
    fi

    if /sbin/dhclient ${DHCLIENTARGS} ${DEVICE} ; then
	echo $" done."
    else
	echo $" failed."
	exit 1
    fi
# end dynamic device configuration
else 
    if [ -z "${IPADDR}" ]; then
         # enable device without IP, useful for e.g. PPPoE
	 ip link set dev ${REALDEVICE} up
	 if [ -n "$ETHTOOL_OPTS" ] ; then
	 	/sbin/ethtool -s ${REALDEVICE} $ETHTOOL_OPTS
	 fi
	 # Bonding initialization part II
	 if [ "${TYPE}" =  "Bonding" ] || ethtool -i $DEVICE 2>/dev/null| grep -q "driver: bonding" ; then
    		for device in `LANG=C grep -l "^[[:space:]]*MASTER=${DEVICE}" /etc/sysconfig/network-scripts/ifcfg-*` ; do
			/sbin/ifup ${device##*/}
    		done
	 fi

	 if [ "${NETWORKING_IPV6}" = "yes" ]; then
	    /etc/sysconfig/network-scripts/ifup-ipv6 ${CONFIG}
	 fi
	 exec /etc/sysconfig/network-scripts/ifup-post ${CONFIG} ${2}
    fi
  
    expand_config
    
    [ -n "${ARP}" ] && \
	ip link set dev ${REALDEVICE} $(toggle_value arp $ARP)
   
    if ! ip link set dev ${REALDEVICE} up ; then
	echo $"Failed to bring up ${DEVICE}."
	exit 1
    fi

    if [ -n "$ETHTOOL_OPTS" ] ; then
        /sbin/ethtool -s ${REALDEVICE} $ETHTOOL_OPTS
    fi

    if ! arping -q -c 2 -w 3 -D -I ${REALDEVICE} ${IPADDR} ; then
	echo $"Error, some other host already uses address ${IPADDR}."
	exit 1
    fi

    if [ "${DEVICE}" = "lo" ]; then
    	SCOPE="scope host"
    else
        SCOPE=${SCOPE:-}
    fi
    
    if [ -n "$SRCADDR" ]; then
       SRC="src $SRCADDR"
    else
       SRC=
    fi
    
    if ! LC_ALL=C ip addr ls ${REALDEVICE} | LC_ALL=C grep -q "${IPADDR}/${PREFIX}" ; then
	 if ! ip addr add ${IPADDR}/${PREFIX} \
	    brd ${BROADCAST:-+} dev ${REALDEVICE} ${SCOPE} label ${DEVICE}; then
	    echo $"Error adding address ${IPADDR} for ${DEVICE}."
	 fi
    fi
    
    if [ -n "$SRCADDR" ]; then
           sysctl -w "net.ipv4.conf.${REALDEVICE}.arp_filter=1" >/dev/null 2>&1
    fi

    # update ARP cache of neighboring computers
    arping -q -A -c 1 -I ${REALDEVICE} ${IPADDR}
    ( sleep 2;
      arping -q -U -c 1 -I ${REALDEVICE} ${IPADDR} ) > /dev/null 2>&1 < /dev/null &

    # Set a default route.
    if [ -z "${GATEWAYDEV}" -o "${GATEWAYDEV}" = "${REALDEVICE}" ]; then
	# set up default gateway. replace if one already exists
	if [ -n "${GATEWAY}" -a "`ipcalc --network ${GATEWAY} ${NETMASK} 2>/dev/null`" = "NETWORK=${NETWORK}" ]; then
	    ip route replace default via ${GATEWAY} ${WINDOW:+window $WINDOW} ${SRC} ${GATEWAYDEV:+dev $GATEWAYDEV}
	elif [ "${GATEWAYDEV}" = "${DEVICE}" ]; then
	    ip route replace default ${SRC} ${WINDOW:+window $WINDOW} dev ${REALDEVICE}
	fi
    fi
    
fi

# Bonding initialization part II - for static, enslave the devices. For
# DHCP, remove any routes for the slaves.
if [ "${TYPE}" =  "Bonding" ] || ethtool -i $DEVICE 2>/dev/null| grep -q "driver: bonding" ; then
    for device in `LANG=C grep -l "^[[:space:]]*MASTER=${DEVICE}" /etc/sysconfig/network-scripts/ifcfg-*` ; do
	if [ "$BOOTPROTO" = "dhcp" ]; then
		DEV=$DEVICE
                eval $(LANG=C fgrep "DEVICE=" $device)
		ifenslave -d $DEV $DEVICE
		DEVICE=$DEV
	fi
	/sbin/ifup ${device##*/}
    done
fi

# Add Zeroconf route.
if [ -z "${NOZEROCONF}" -a "${ISALIAS}" = "no" ]; then
    ip route replace 169.254.0.0/16 dev ${REALDEVICE} 
fi

# IPv6 initialisation?
if [ "${NETWORKING_IPV6}" = "yes" ]; then
    /etc/sysconfig/network-scripts/ifup-ipv6 ${CONFIG}
    if [[ "${DHCPV6C}"  = [Yy1]* ]] && [ -x /sbin/dhcp6c ]; then
	/sbin/dhcp6c ${DEVICE};
        dhcp6_pid=(`/bin/ps -eo 'pid,args' | /bin/grep "dhcp6c ${DEVICE}" | egrep -v grep`);
	echo ${dhcp6_pid[0]} > /var/run/dhcp6c_${DEVICE}.pid
    fi;
fi

if [ "${IPX}" = yes ]; then
       /etc/sysconfig/network-scripts/ifup-ipx ${DEVICE}
fi

exec /etc/sysconfig/network-scripts/ifup-post ${CONFIG} ${2}