aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--changes.ipv611
-rw-r--r--ipv6-6to4.howto18
-rw-r--r--sysconfig/network-scripts/network-functions-ipv674
3 files changed, 48 insertions, 55 deletions
diff --git a/changes.ipv6 b/changes.ipv6
index 250e507e..1970e98e 100644
--- a/changes.ipv6
+++ b/changes.ipv6
@@ -1,4 +1,4 @@
-v1.5 4th Dec 2002, Pekka Savola <pekkas@netcore.fi>
+v1.6 2nd Sep 2003, Pekka Savola <pekkas@netcore.fi>
IPv6 CHANGES
============
@@ -6,8 +6,13 @@ IPv6 CHANGES
This mentions the most important changes (visible to the administrator)
in IPv6 initscripts.
-RHL80 -> CURRENT
-----------------
+RHL9 -> CURRENT
+---------------
+
+ - no major functional changes, only bugfixes and cleanups
+
+RHL80 -> RHL9
+-------------
- 6to4 device MTU is calculated explicitly, IPV6TO4_MTU support added
- add route6-<device> static route support
diff --git a/ipv6-6to4.howto b/ipv6-6to4.howto
index b42704b8..707908d8 100644
--- a/ipv6-6to4.howto
+++ b/ipv6-6to4.howto
@@ -1,4 +1,4 @@
-v1.4 10th Jan 2002, Pekka Savola <pekkas@netcore.fi>
+v1.5 1st Sep 2003, Pekka Savola <pekkas@netcore.fi>
HOW TO SET UP IPV6 WITH 6TO4
----------------------------
@@ -120,7 +120,7 @@ Usually the following is enough:
2. Configure radvd as outlined in radvd.conf(5); the file could
be something like:
- interface eth0
+ interface eth1
{
AdvSendAdvert on;
MinRtrAdvInterval 3;
@@ -145,6 +145,18 @@ Usually the following is enough:
IPV6_CONTROL_RADVD=yes
+5. Configure the associated routes to other 6to4 subnets to point at
+ your LAN interfaces; this can be done automatically with
+ IPV6TO4_ROUTING variable; please refer sysconfig.txt for details.
+ In the particular example, above, this would be like:
+
+ /etc/sysconfig/network-scripts/ifcfg-eth0:
+
+ IPV6TO4_ROUTING="eth1-:1::0/64"
+
+ However, please note that no global address is configured on the
+ interface, just a route!
+
MORE INFORMATION
----------------
@@ -157,6 +169,6 @@ Clouds") is the RFC about 6to4.
ftp://ftp.isi.edu/in-notes/rfc3068.txt ("An Anycast Prefix for 6to4 Relay
Routers") is the RFC about finding a close 6to4 relay automatically.
-http:://www.ietf.org/internet-drafts/draft-savola-ngtrans-6to4-security-00.txt
+http://www.ietf.org/internet-drafts/draft-savola-v6ops-6to4-security-02.txt
("Security Considerations and Enhancements for 6to4") explains some
security considerations in 6to4.
diff --git a/sysconfig/network-scripts/network-functions-ipv6 b/sysconfig/network-scripts/network-functions-ipv6
index bf9a4576..e5284411 100644
--- a/sysconfig/network-scripts/network-functions-ipv6
+++ b/sysconfig/network-scripts/network-functions-ipv6
@@ -137,7 +137,7 @@ ipv6_log() {
fi
;;
'syslog')
-
+ # note: logger resides in /usr/bin, but not used by default
if ! [ -x logger ]; then
echo $"ERROR: [ipv6_log] Syslog is chosen, but binary 'logger' doesn't exist or isn't executable" >/dev/stderr
return 3
@@ -509,7 +509,7 @@ ipv6_disable_autotunnel() {
if ipv6_exec_route -A inet6 -n 2>/dev/null | LC_ALL=C grep "sit0\W*$" | awk '{ print $2 }' | LC_ALL=C grep -v -q "^::$"; then
# still existing routes, skip shutdown of sit0
true
- elif ipv6_exec_ip addr show dev sit0 | LC_ALL=C grep inet6 | awk '{ print $2 }' | LC_ALL=C grep -v -q '^::'; then
+ elif ipv6_exec_ip -6 -o addr show dev sit0 | awk '{ print $4 }' | LC_ALL=C grep -v -q '^::'; then
# still existing IPv6 addresses, skip shutdown of sit0
true
else
@@ -583,7 +583,7 @@ ipv6_test_addr_exists_on_device() {
fi
else
# low budget version, only works if given address is in equal form like "ip" displays
- local testresult="`ipv6_exec_ip addr show dev $testdevice | LC_ALL=C grep -w inet6 | awk '{ print $2 }' | LC_ALL=C grep -i "^$testaddr/$testprefix$"`"
+ local testresult="`ipv6_exec_ip -o -6 addr show dev $testdevice | awk '{ print $4 }' | LC_ALL=C grep -i "^$testaddr/$testprefix$"`"
if [ -n "$testresult" ]; then
# exists
return 0
@@ -598,41 +598,6 @@ ipv6_test_addr_exists_on_device() {
}
-##### Test, whether an IPv6 address with given prefix exists on an interface
-# $1: <Interface> : to test
-# $2: <Prefix>
-# return values: 0=ok (exists) 1=argument error 3=major problem 10=not exists
-ipv6_test_addrprefix_exists_on_device() {
- local fn="ipv6_test_addr_prefix_exists_on_device"
-
- local testdevice=$1
- local testaddrprefix=$2
-
- if [ -z "$testdevice" ]; then
- ipv6_log $"Missing parameter 'device' (arg 1)" err $fn
- return 1
- fi
- if [ -z "$testaddrprefix" ]; then
- ipv6_log $"Missing parameter 'IPv6 address prefix' (arg 2)" err $fn
- return 1
- fi
-
- ipv6_test testonly || return 2
-
- # For the moment: low budget version, only works if given address is in equal form like "ip" displays
- local testresult="`ipv6_exec_ip addr show dev $testdevice | LC_ALL=C grep inet6 | awk '{ print $2 }' | LC_ALL=C grep -i "^$testaddrprefix:"`"
- if [ -n "$testresult" ]; then
- # exists
- return 0
- else
- # not exists
- return 10
- fi
-
- # Normally this lines not reached
- return 3
-}
-
##### Interface configuration
@@ -1081,13 +1046,16 @@ ipv6_add_6to4_tunnel() {
local address6to4="${prefix6to4}::${localipv6to4suffix}/16"
fi
- ipv6_add_tunnel_device tun6to4 0.0.0.0 $address6to4 $ipv4addr
+ ipv6_add_tunnel_device tun6to4 0.0.0.0 $address6to4 $localipv4
if [ $? -ne 0 ]; then
local retval=3
else
local retval=0
fi
+ # Add unspecific unreachable route for local 6to4 address space
+ ipv6_exec_ip route add unreach ${prefix6to4}::/48
+
# Set MTU, if given
if [ -n "$mtu" ]; then
ipv6_set_mtu $device $mtu
@@ -1120,6 +1088,11 @@ ipv6_cleanup_6to4_tunnels() {
ipv6_del_tunnel_device tun6to4
+ # Remove all unspecific unreachable routes for local 6to4 address space
+ ipv6_exec_ip -6 route | LC_ALL=C grep "^unreachable 2002:" | LC_ALL=C grep "/48 dev lo" | while read token net rest; do
+ ipv6_exec_ip route del unreach $net
+ done
+
return 0
}
@@ -1155,6 +1128,9 @@ ipv6_del_6to4_tunnel() {
ipv6_del_tunnel_device tun6to4
local retval=$?
+ # Remove unspecific unreachable route for local 6to4 address space
+ ipv6_exec_ip route del unreach ${prefix6to4}::/48
+
return $retval
}
@@ -1273,7 +1249,7 @@ ipv6_del_tunnel_device() {
fi
if [ "$device" != "sit0" ]; then
- if ipv6_exec_ip tunnel 2>/dev/null | LC_ALL=C grep -q "^$device:" ; then
+ if ipv6_exec_ip tunnel show $device 2>/dev/null | LC_ALL=C grep -q -w "ipv6/ip"; then
ipv6_exec_ip tunnel del $device
if ipv6_test_device_status $device; then
@@ -1296,7 +1272,7 @@ ipv6_cleanup_tunnel_devices() {
# Find still existing tunnel devices and shutdown and delete them
- ipv6_exec_ip tunnel | LC_ALL=C grep -w "ipv6/ip" | awk -F: '{ print $1 }' | while read device; do
+ ipv6_exec_ip tunnel show | LC_ALL=C grep -w "ipv6/ip" | awk -F: '{ print $1 }' | while read device; do
ipv6_del_tunnel_device $device
done
@@ -1362,7 +1338,7 @@ ipv6_get_ipv4addr_of_tunnel() {
## Get IPv4 address of a device
# $1: <Interface>
# stdout: <IPv4 address> if available
-# return code: 0=ok 1=argument error 2=IPv6 test fails 3=major problem
+# return code: 0=ok 1=argument error 2=IPv6 test fails 3=major problem (more than one IPv4 address applied)
ipv6_get_ipv4addr_of_device() {
local fn="ipv6_get_ipv4addr_of_device"
@@ -1380,8 +1356,8 @@ ipv6_get_ipv4addr_of_device() {
return 3
fi
- # Device exists, retrieve address
- local ipv4addr="`ipv6_exec_ip -4 addr show dev $device | LC_ALL=C grep -w "inet" | awk '{ print $2 }' | awk -F/ '{ print $1 }'`"
+ # Device exists, retrieve the first address only
+ local ipv4addr="`ipv6_exec_ip -o -4 addr show dev $device | awk '{ print $4 }' | awk -F/ '{ print $1; exit }'`"
if [ $? != 0 ]; then
return 3
@@ -1438,9 +1414,9 @@ ipv6_set_mtu() {
}
-## Set a default gateway
-# $1: <IPv6 Address> : gateway, can also contain scope suffix (device name), cause a warning if not matching with $2 (but will have precedence)
-# $2: <gateway device>: specified gateway device (has
+## Set a default route
+# $1: <IPv6 address> : gateway, can also contain scope suffix (device name), cause a warning if not matching with $2 (but will have precedence)
+# $2: <gateway device>: gateway device (optional in case of $1 is a global address or $1 contains scope suffix)
# $3: <check device>: (optional) device to check scope and gateway device against (setup is skipped, if not matching)
# return code: 0=ok 1=argument error 2=IPv6 test fails 3=major problem
ipv6_set_default_route() {
@@ -1494,7 +1470,7 @@ ipv6_set_default_route() {
fi
fi
- # Set device now, if given
+ # Set device now, if not given
if [ -z "$device" ]; then
local device="$device_scope"
fi
@@ -1561,7 +1537,7 @@ ipv6_test_route_requires_next_hop() {
return 10
fi
- if ipv6_exec_ip link show $device 2>/dev/null | LC_ALL=C grep -q "POINTOPOINT"; then
+ if ipv6_exec_ip -o link show $device 2>/dev/null | LC_ALL=C grep -q "POINTOPOINT"; then
return 10
fi