package detect_devices; # $Id$ use diagnostics; use strict; use vars qw($pcitable_addons $usbtable_addons); #-###################################################################################### #- misc imports #-###################################################################################### use log; use common; use devices; use run_program; use modules; use c; use feature 'state'; #-##################################################################################### #- Globals #-##################################################################################### my %serialprobe; #-###################################################################################### #- Functions #-###################################################################################### sub get() { #- Detect the default BIOS boot harddrive is kind of tricky. We may have IDE, #- SCSI and RAID devices on the same machine. From what I see so far, the default #- BIOS boot harddrive will be #- 1. The first IDE device if IDE exists. Or #- 2. The first SCSI device if SCSI exists. Or #- 3. The first RAID device if RAID exists. getIDE(), getSCSI(), getDAC960(), getCompaqSmartArray(), getATARAID(); } sub hds() { grep { may_be_a_hd($_) } get() } sub tapes() { grep { $_->{media_type} eq 'tape' } get() } sub cdroms() { grep { $_->{media_type} eq 'cdrom' } get() } sub burners() { grep { isBurner($_) } cdroms() } sub dvdroms() { grep { isDvdDrive($_) } cdroms() } sub raw_zips() { grep { member($_->{media_type}, 'fd', 'hd') && isZipDrive($_) } get() } sub ls120s() { grep { member($_->{media_type}, 'fd', 'hd') && isLS120Drive($_) } get() } sub zips() { map { $_->{device} .= 4; $_; } raw_zips(); } sub floppies { my ($o_not_detect_legacy_floppies) = @_; require modules; my @fds; state $legacy_already_detected; if (!$o_not_detect_legacy_floppies && !$legacy_already_detected) { $legacy_already_detected = 1; eval { modules::load("floppy") if $::isInstall }; #- do not bother probing /dev/fd0 and loading floppy device uselessly, #- it takes time and it is already done by boot process (if not in install): #- /dev/fd0 is created by start_udev (/etc/udev/devices.d/default.nodes) #- then hal probes /dev/fd0 and triggers floppy module loading through kernel's kmod if (any { (split)[1] eq 'fd' } cat_("/proc/devices")) { @fds = map { my $info = c::floppy_info(devices::make("fd$_")); if_($info && $info ne '(null)', { device => "fd$_", media_type => 'fd', info => $info }); } qw(0 1); } } my @ide = ls120s() and eval { modules::load("ide_floppy") }; eval { modules::load("usb_storage") } if $::isInstall && usbStorage(); my @scsi = grep { $_->{media_type} eq 'fd' } getSCSI(); @ide, @scsi, @fds; } sub floppies_dev() { map { $_->{device} } floppies() } sub floppy() { first(floppies_dev()) } #- example ls120, model = "LS-120 SLIM 02 UHD Floppy" sub removables() { floppies(), cdroms(), zips(); } sub get_sys_cdrom_info { my (@drives) = @_; my @drives_order; foreach (cat_("/proc/sys/dev/cdrom/info")) { my ($t, $l) = split ':'; my @l; @l = split(' ', $l) if $l; if ($t eq 'drive name') { @drives_order = map { my $dev = $_; find { $_->{device} eq $dev } @drives; } @l; } else { my $capacity; if ($t eq 'Can write CD-R') { $capacity = 'burner'; } elsif ($t eq 'Can read DVD') { $capacity = 'DVD'; } if ($capacity) { each_index { ($drives_order[$::i] || {})->{capacity} .= "$capacity " if $_; } @l; } } } } sub complete_usb_storage_info { my (@l) = @_; my @usb = grep { exists $_->{usb_vendor} } @l; foreach my $usb (usb_probe()) { if (my $e = find { !$_->{found} && $_->{usb_vendor} == $usb->{vendor} && $_->{usb_id} == $usb->{id} } @usb) { my $host = get_sysfs_usbpath_for_block($e->{device}); if ($host) { $e->{info} = chomp_(cat_("/sys/block/$e->{device}/$host/../serial")); $e->{usb_description} = join('|', chomp_(cat_("/sys/block/$e->{device}/$host/../manufacturer")), chomp_(cat_("/sys/block/$e->{device}/$host/../product"))); } local $e->{found} = 1; $e->{"usb_$_"} ||= $usb->{$_} foreach keys %$usb; } } } sub isBurner { my ($e) = @_; $e->{capacity} =~ /burner/ and return 1; #- do not work for SCSI my $f = tryOpen($e->{device}); #- SCSI burner are not detected this way. $f && c::isBurner(fileno($f)); } sub isDvdDrive { my ($e) = @_; $e->{capacity} =~ /DVD/ || $e->{info} =~ /DVD/ and return 1; #- do not work for SCSI my $f = tryOpen($e->{device}); $f && c::isDvdDrive(fileno($f)); } sub isZipDrive { $_[0]{info} =~ /ZIP\s+\d+/ } #- accept ZIP 100, untested for bigger ZIP drive. sub isLS120Drive { $_[0]{info} =~ /LS-?120|144MB/ } sub isKeyUsb { begins_with($_[0]{usb_media_type} || '', 'Mass Storage') && $_[0]{media_type} eq 'hd' } sub isFloppyUsb { $_[0]{usb_driver} && $_[0]{usb_driver} eq 'Removable:floppy' } sub may_be_a_hd { my ($e) = @_; $e->{media_type} eq 'hd' && !( isZipDrive($e) || isLS120Drive($e) || begins_with($e->{usb_media_type} || '', 'Mass Storage|Floppy (UFI)') ); } sub get_sysfs_field_from_link { my ($device, $field) = @_; my $l = readlink("$device/$field"); $l =~ s!.*/!!; $l; } sub get_sysfs_usbpath_for_block { my ($device) = @_; my $host = readlink("/sys/block/$device/device"); $host =~ s!/host.*!!; $host; } sub get_scsi_driver { my (@l) = @_; # find driver of host controller from sysfs: foreach (@l) { next if $_->{driver}; my $host = get_sysfs_usbpath_for_block($_->{device}); $_->{driver} = get_sysfs_field_from_link("/sys/block/$_->{device}/$host", 'driver'); } } sub getSCSI() { my $dev_dir = '/sys/bus/scsi/devices'; my @scsi_types = ( "Direct-Access", "Sequential-Access", "Printer", "Processor", "WORM", "CD-ROM", "Scanner", "Optical Device", "Medium Changer", "Communications", ); my @l; foreach (all($dev_dir)) { my ($host, $channel, $id, $lun) = split ':' or log::l("bad entry in $dev_dir: $_"), next; my $dir = "$dev_dir/$_"; # handle both old and new kernels: my $node = find { -e $_ } "$dir/block", top(glob_("$dir/block*")), "$dir/tape", top(glob_("$dir/scsi_generic*")); my ($device) = readlink($node) =~ m!/(?:scsi_(?:generic|tape)|block)/(.*)!; if (!$device) { ($device) = top(glob_("$node/*")) =~ m!/(?:scsi_(?:generic|tape)|block)/(.*)!; } warn("cannot get info for device ($_)"), next if !$device; my $usb_dir = readlink("$node/device") =~ m!/usb! && "$node/device/../../../.."; my $get_usb = sub { chomp_(cat_("$usb_dir/$_[0]")) }; my $get = sub { my $s = cat_("$dir/$_[0]"); $s =~ s/\s+$//; $s; }; # Old hp scanners report themselves as "Processor"s # (see linux/include/scsi/scsi.h and sans-find-scanner.1) my $raw_type = $scsi_types[$get->('type')]; my $media_type = ${{ st => 'tape', sr => 'cdrom', sd => 'hd', sg => 'generic' }}{substr($device, 0, 2)} || $raw_type =~ /Scanner|Processor/ && 'scanner'; push @l, { info => $get->('vendor') . ' ' . $get->('model'), host => $host, channel => $channel, id => $id, lun => $lun, description => join('|', $get->('vendor'), $get->('model')), bus => 'SCSI', media_type => $media_type, device => $device, $usb_dir ? ( usb_vendor => hex($get_usb->('idVendor')), usb_id => hex($get_usb->('idProduct')), ) : (), }; } @l = sort { $a->{host} <=> $b->{host} || $a->{channel} <=> $b->{channel} || $a->{id} <=> $b->{id} || $a->{lun} <=> $b->{lun} } @l; complete_usb_storage_info(@l); foreach (@l) { $_->{media_type} = 'fd' if $_->{media_type} eq 'hd' && isFloppyUsb($_); } get_sys_cdrom_info(@l); get_scsi_driver(@l); @l; } my %eide_hds = ( "ASUS" => "Asus", "CD-ROM CDU" => "Sony", "CD-ROM Drive/F5D" => "ASUSTeK", "Compaq" => "Compaq", "CONNER" => "Conner Peripherals", "IBM" => "IBM", "FUJITSU" => "Fujitsu", "HITACHI" => "Hitachi", "Lite-On" => "Lite-On Technology Corp.", "LITE-ON" => "Lite-On Technology Corp.", "LTN" => "Lite-On Technology Corp.", "IOMEGA" => "Iomega", "MAXTOR" => "Maxtor", "Maxtor" => "Maxtor", "Micropolis" => "Micropolis", "Pioneer" => "Pioneer", "PLEXTOR" => "Plextor", "QUANTUM" => "Quantum", "SAMSUNG" => "Samsung", "Seagate " => "Seagate Technology", "ST3" => "Seagate Technology", "TEAC" => "Teac", "TOSHIBA" => "Toshiba", "WDC" => "Western Digital Corp.", ); sub getIDE() { my @idi; #- what about a system with absolutely no IDE on it, like some sparc machine. -e "/proc/ide" or return (); #- Great. 2.2 kernel, things are much easier and less error prone. foreach my $d (sort @{[glob_('/proc/ide/hd*')]}) { cat_("$d/driver") =~ /ide-scsi/ and next; #- already appears in /proc/scsi/scsi my $t = chomp_(cat_("$d/media")); my $type = ${{ disk => 'hd', cdrom => 'cdrom', tape => 'tape', floppy => 'fd' }}{$t} or next; my $info = chomp_(cat_("$d/model")) || "(none)"; my $num = ord(($d =~ /(.)$/)[0]) - ord 'a'; my ($vendor, $model) = map { if_($info =~ /^$_(-|\s)*(.*)/, $eide_hds{$_}, $2); } keys %eide_hds; my $host = $num; ($host, my $id) = divide($host, 2); ($host, my $channel) = divide($host, 2); push @idi, { media_type => $type, device => basename($d), info => $info, host => $host, channel => $channel, id => $id, bus => 'ide', if_($vendor, Vendor => $vendor), if_($model, Model => $model) }; } get_sys_cdrom_info(@idi); @idi; } sub block_devices() { -d '/sys/block' ? map { s|!|/|; $_ } all('/sys/block') : map { $_->{dev} } do { require fs::proc_partitions; fs::proc_partitions::read_raw() }; } sub getCompaqSmartArray() { my (@idi, $f); foreach ('array/ida', 'cpqarray/ida', 'cciss/cciss') { my $prefix = "/proc/driver/$_"; #- kernel 2.4 places it here $prefix = "/proc/$_" if !-e "${prefix}0"; #- kernel 2.2 my ($name) = m|/(.*)|; for (my $i = 0; -r ($f = "${prefix}$i"); $i++) { my @raw_devices = cat_($f) =~ m|^\s*($name/.*?):|gm; #- this is ugly and buggy. keeping it for 2007.0 #- on a cciss, cciss/cciss0 didn't contain c0d0, but cciss/cciss1 did contain c0d1 #- the line below adds both c0d0 and c0d1 for cciss0, and so some duplicates @raw_devices or @raw_devices = grep { m!^$name/! } block_devices(); foreach my $raw_device (@raw_devices) { my $device = -d "/dev/$raw_device" ? "$raw_device/disc" : $raw_device; push @idi, { device => $device, prefix => $raw_device . 'p', info => "Compaq RAID logical disk", media_type => 'hd', bus => $name }; } } } #- workaround the buggy code above. this should be safe though uniq_ { $_->{device} } @idi; } sub getDAC960() { my %idi; #- We are looking for lines of this format:DAC960#0: #- /dev/rd/c0d0: RAID-7, Online, 17928192 blocks, Write Thru0123456790123456789012 foreach (syslog()) { my ($device, $info) = m|/dev/(rd/.*?): (.*?),| or next; $idi{$device} = { info => $info, media_type => 'hd', device => $device, bus => 'dac960' }; } values %idi; } sub getATARAID() { my %l; foreach (syslog()) { my ($device) = m|^\s*(ataraid/d\d+):| or next; $l{$device} = { info => 'ATARAID block device', media_type => 'hd', device => $device, bus => 'ataraid' }; log::l("ATARAID: $device"); } values %l; } # cpu_name : arch() =~ /^alpha/ ? "cpu " : # arch() =~ /^ppc/ ? "processor" : "vendor_id" # cpu_model : arch() =~ /^alpha/ ? "cpu model" : # arch() =~ /^ppc/ ? "cpu " : "model name" # cpu_freq = arch() =~ /^alpha/ ? "cycle frequency [Hz]" : # arch() =~ /^ppc/ ? "clock" : "cpu MHz" sub getCPUs() { my (@cpus, $cpu); foreach (cat_("/proc/cpuinfo")) { if (/^processor/) { # ix86 specific push @cpus, $cpu if $cpu; $cpu = {}; } $cpu->{$1} = $2 if /^([^\t]+).*:\s(.*)$/; $cpu->{processor}++ if $1 eq "processor"; } push @cpus, $cpu; @cpus; } sub ix86_cpu_frequency() { cat_('/proc/cpuinfo') =~ /cpu MHz\s*:\s*(\d+)/ && $1; } sub probe_category { my ($category) = @_; require list_modules; my @modules = list_modules::category2modules($category); if_($category =~ /sound/ && arch() =~ /ppc/ && get_mac_model() !~ /IBM/, { driver => 'snd_powermac', description => 'Macintosh built-in' }, ), grep { if ($category eq 'network/isdn') { my $b = $_->{driver} =~ /ISDN:([^,]*),?([^,]*)(?:,firmware=(.*))?/; if ($b) { $_->{driver} = $1; $_->{type} = $2; $_->{type} =~ s/type=//; $_->{firmware} = $3; $_->{driver} eq "hisax" and $_->{options} .= " id=HiSax"; } $b; } else { member($_->{driver}, @modules); } } probeall(); } sub getSoundDevices() { probe_category('multimedia/sound'); } sub isTVcardConfigurable { member($_[0]{driver}, qw(bttv cx88 saa7134)) } sub getTVcards() { probe_category('multimedia/tv') } sub getInputDevices() { my (@devices, $device); foreach (cat_('/proc/bus/input/devices')) { if (/^I:/) { $device = {}; $device->{vendor} = /Vendor=(\w+)/ && $1; $device->{id} = /Product=(\w+)/ && $1; $device->{bustype} = /Bus=(\w+)/ && $1; } elsif (/N: Name="(.*)"/) { my $descr = $1; $device->{description} = "|$descr"; #- I: Bus=0011 Vendor=0002 Product=0008 Version=7321 #- N: Name="AlpsPS/2 ALPS GlidePoint" #- P: Phys=isa0060/serio1/input0 #- H: Handlers=mouse1 event2 ts1 #- B: EV=f #- B: KEY=420 0 70000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT BTN_MIDDLE BTN_TOOL_FINGER BTN_TOUCH #- or B: KEY=420 0 670000 0 0 0 0 0 0 0 0 #=> same with BTN_BACK #- B: REL=3 #=> X Y #- B: ABS=1000003 #=> X Y PRESSURE #- I: Bus=0011 Vendor=0002 Product=0008 Version=2222 #- N: Name="AlpsPS/2 ALPS DualPoint TouchPad" #- P: Phys=isa0060/serio1/input0 #- S: Sysfs=/class/input/input2 #- H: Handlers=mouse1 ts1 event2 #- B: EV=f #- B: KEY=420 0 70000 0 0 0 0 0 0 0 0 #- B: REL=3 #- B: ABS=1000003 #- I: Bus=0011 Vendor=0002 Product=0007 Version=0000 #- N: Name="SynPS/2 Synaptics TouchPad" #- P: Phys=isa0060/serio1/input0 #- S: Sysfs=/class/input/input1 #- H: Handlers=mouse0 event1 ts0 #- B: EV=b #- B: KEY=6420 0 70000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT BTN_MIDDLE BTN_TOOL_FINGER BTN_TOUCH BTN_TOOL_DOUBLETAP BTN_TOOL_TRIPLETAP #- or B: KEY=6420 0 670000 0 0 0 0 0 0 0 0 #=> same with BTN_BACK #- or B: KEY=420 30000 670000 0 0 0 0 0 0 0 0 #=> same without BTN_TOOL_TRIPLETAP but with BTN_B #- B: ABS=11000003 #=> X Y PRESSURE TOOL_WIDTH #- I: Bus=0003 Vendor=056a Product=0065 Version=0108 #- N: Name="Wacom Bamboo" #- B: KEY=1c63 0 70033 0 0 0 0 0 0 0 0 #=> BTN_0 BTN_1 BTN_4 BTN_5 BTN_LEFT BTN_RIGHT BTN_MIDDLE TOOL_PEN TOOL_RUBBER TOOL_BRUSH TOOL_FINGER TOOL_MOUSE TOUCH STYLUS STYLUS2 #- B: ABS=100 3000103 #=> X Y WHEEL PRESSURE DISTANCE MISC #- I: Bus=0003 Vendor=056a Product=0011 Version=0201 #- N: Name="Wacom Graphire2 4x5" #- B: KEY=1c43 0 70000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT BTN_MIDDLE TOOL_PEN TOOL_RUBBER TOOL_FINGER TOOL_MOUSE TOUCH STYLUS STYLUS2 #- B: ABS=100 3000003 #=> X Y PRESSURE DISTANCE MISC $device->{Synaptics} = $descr eq 'SynPS/2 Synaptics TouchPad'; $device->{ALPS} = $descr =~ m!^AlpsPS/2 ALPS!; } elsif (/H: Handlers=(.*)/) { my @l = split(' ', $1); $device->{driver} = $l[0]; #- keep it for compatibility $device->{Handlers} = +{ map { (/^(.*?)\d*$/ ? $1 : $_, $_) } split(' ', $1) }; } elsif (/S: Sysfs=(.+)/) { $device->{sysfs_path} = $1; } elsif (/P: Phys=(.*)/) { $device->{location} = $1; $device->{bus} = 'isa' if $device->{location} =~ /^isa/; $device->{bus} = 'usb' if $device->{location} =~ /^usb/i; } elsif (/B: REL=(.* )?(.*)/) { #- REL=3 #=> X Y #- REL=103 #=> X Y WHEEL #- REL=143 #=> X Y HWHEEL WHEEL #- REL=1c3 #=> X Y HWHEEL DIAL WHEEL my $REL = hex($2); $device->{HWHEEL} = 1 if $REL & (1 << 6); $device->{WHEEL} = 1 if $REL & (1 << 8); #- not reliable ("Mitsumi Apple USB Mouse" says REL=103 and KEY=1f0000 ...) } elsif (/B: KEY=(\S+)/) { #- some KEY explained: #- (but note that BTN_MIDDLE can be reported even if missing) #- (and "Mitsumi Apple USB Mouse" reports 1f0000) #- KEY=30000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT #- KEY=70000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT BTN_MIDDLE #- KEY=1f0000 0 0 0 0 0 0 0 0 #=> BTN_LEFT BTN_RIGHT BTN_MIDDLE BTN_SIDE BTN_EXTRA my $KEY = hex($1); $device->{SIDE} = 1 if $KEY & (1 << 0x13); } elsif (/^\s*$/) { push @devices, $device if $device; undef $device; } } @devices; } sub getInputDevices_and_usb() { my @l = getInputDevices(); foreach my $usb (usb_probe()) { if (my $e = find { hex($_->{vendor}) == $usb->{vendor} && hex($_->{id}) == $usb->{id} } @l) { $e->{usb} = $usb; } } @l; } sub getSerialModem { my ($modules_conf, $o_mouse) = @_; my $mouse = $o_mouse || {}; $mouse->{device} = readlink "/dev/mouse"; my $serdev = arch() =~ /ppc/ ? "macserial" : "serial"; eval { modules::load($serdev) }; my @modems; probeSerialDevices(); foreach my $port (map { "ttyS$_" } (0..7)) { next if $mouse->{device} =~ /$port/; my $device = "/dev/$port"; next if !-e $device || !hasModem($device); $serialprobe{$device}{device} = $device; push @modems, $serialprobe{$device}; } my @devs = pcmcia_probe(); foreach my $modem (@modems) { #- add an alias for macserial on PPC $modules_conf->set_alias('serial', $serdev) if arch() =~ /ppc/ && $modem->{device}; foreach (@devs) { $_->{device} and $modem->{device} = $_->{device} } } @modems; } sub getModem { my ($modules_conf) = @_; getSerialModem($modules_conf, {}), get_winmodems(); } sub get_winmodems() { matching_driver__regexp('www\.linmodems\.org'), matching_driver(list_modules::category2modules('network/modem'), list_modules::category2modules('network/slmodem')); } sub getBewan() { matching_desc__regexp('Bewan Systems\|.*ADSL|BEWAN ADSL USB|\[Unicorn\]'); } # generate from the following from eci driver sources: # perl -e 'while (<>) { print qq("$1$2",\n"$3$4",\n) if /\b([a-z\d]*)\s*([a-z\d]*)\s*([a-z\d]*)\s*([a-z\d]*)$/ }' {vendor}, $_->{id}, $_->{subvendor}, $_->{subid}), @ids) } usb_probe(); } sub get_xdsl_usb_devices() { my @bewan = detect_devices::getBewan(); $_->{driver} = $_->{bus} eq 'USB' ? 'unicorn_usb_atm' : 'unicorn_pci_atm' foreach @bewan; my @eci = detect_devices::getECI(); $_->{driver} = 'eciusb' foreach @eci; my @usb = detect_devices::probe_category('network/usb_dsl'); $_->{description} = "USB ADSL modem (eagle chipset)" foreach grep { $_->{driver} eq 'ueagle_atm' && $_->{description} eq '(null)' } @usb; @usb, @bewan, @eci; } sub is_lan_interface { #- we want LAN like interfaces here (eg: ath|br|eth|fddi|plip|ra|tr|usb|wlan). #- there's also bnep%d for bluetooth, bcp%d... #- we do this by blacklisting the following interfaces: #- hso%d are created by drivers/net/usb/hso.c #- ippp|isdn|plip|ppp (initscripts suggest that isdn%d can be created but kernel sources claim not) #- ippp%d are created by drivers/isdn/i4l/isdn_ppp.c #- plip%d are created by drivers/net/plip.c #- ppp%d are created by drivers/net/ppp_generic.c is_useful_interface($_[0]) && $_[0] !~ /^(?:hso|ippp|isdn|plip|ppp)/; } sub is_useful_interface { #- sit0 which is *always* created by net/ipv6/sit.c, thus is always created since net.agent loads ipv6 module #- wifi%d are created by 3rdparty/hostap/hostap_hw.c (pseudo statistics devices, #14523) #- wmaster%d are created by net/mac80211/ieee80211.c ("master" 802.11 device) #- ax*, rose*, nr*, bce* and scc* are Hamradio devices (#28776) $_[0] !~ /^(?:lo|sit0|wifi|wmaster|ax|rose|nr|bce|scc)/; } sub is_wireless_interface { my ($interface) = @_; #- some wireless drivers don't always support the SIOCGIWNAME ioctl #- ralink devices need to be up to support it #- wlan-ng (prism2_*) need some special tweaks to support it #- use sysfs as fallback to detect wireless interfaces, #- i.e interfaces for which get_wireless_stats() is available c::isNetDeviceWirelessAware($interface) || -e "/sys/class/net/$interface/wireless"; } sub get_all_net_devices() { #- we need both detection schemes since: #- get_netdevices() use the SIOCGIFCONF ioctl that does not list interfaces that are down #- /proc/net/dev does not list VLAN and IP aliased interfaces uniq( (map { if_(/^\s*([A-Za-z0-9:\.]*):/, $1) } cat_("/proc/net/dev")), c::get_netdevices(), ); } sub get_lan_interfaces() { grep { is_lan_interface($_) } get_all_net_devices() } sub get_net_interfaces() { grep { is_useful_interface($_) } get_all_net_devices() } sub get_wireless_interface() { find { is_wireless_interface($_) } get_lan_interfaces() } sub is_bridge_interface { my ($interface) = @_; -f "/sys/class/net/$interface/bridge/bridge_id"; } sub get_ids_from_sysfs_device { my ($dev_path) = @_; my $dev_cat = sub { chomp_(cat_("$dev_path/$_[0]")) }; my $usb_root = -f "$dev_path/bInterfaceNumber" && "../" || -f "$dev_path/idVendor" && ""; my $is_pcmcia = -f "$dev_path/card_id"; my $sysfs_ids; my $bus = get_sysfs_field_from_link($dev_path, "bus"); #- FIXME: use $bus if ($is_pcmcia) { $sysfs_ids = { modalias => $dev_cat->('modalias') }; } else { $sysfs_ids = $bus eq 'ieee1394' ? { version => "../vendor_id", specifier_id => "specifier_id", specifier_version => "version", } : defined $usb_root ? { id => $usb_root . 'idProduct', vendor => $usb_root . 'idVendor' } : { id => "device", subid => "subsystem_device", vendor => "vendor", subvendor => "subsystem_vendor" }; $_ = hex($dev_cat->($_)) foreach values %$sysfs_ids; if ($bus eq 'pci') { my $device = basename(readlink $dev_path); my @ids = $device =~ /^(.{4}):(.{2}):(.{2})\.(.+)$/; @{$sysfs_ids}{qw(pci_domain pci_bus pci_device pci_function)} = map { hex($_) } @ids if @ids; } } $sysfs_ids; } sub device_matches_sysfs_ids { my ($device, $sysfs_ids) = @_; every { defined $device->{$_} && member($device->{$_}, $sysfs_ids->{$_}, 0xffff) } keys %$sysfs_ids; } sub device_matches_sysfs_device { my ($device, $dev_path) = @_; device_matches_sysfs_ids($device, get_ids_from_sysfs_device($dev_path)); } #sub getISDN() { # mapgrep(sub {member (($_[0] =~ /\s*(\w*):/), @netdevices), $1 }, split(/\n/, cat_("/proc/net/dev"))); #} sub getUPS() { # MGE serial PnP devices: (map { $_->{port} = $_->{DEVICE}; $_->{bus} = "Serial"; $_->{driver} = "mge-utalk" if $_->{MODEL} =~ /0001/; $_->{driver} = "mge-shut" if $_->{MODEL} =~ /0002/; $_->{media_type} = 'UPS'; $_->{description} = "MGE UPS SYSTEMS|UPS - Uninterruptible Power Supply" if $_->{MODEL} =~ /000[12]/; $_; } grep { $_->{DESCRIPTION} =~ /MGE UPS/ } values %serialprobe), # USB UPSs; (map { ($_->{name} = $_->{description}) =~ s/.*\|//; $_ } map { if ($_->{description} =~ /^American Power Conversion\|Back-UPS/ && $_->{driver} eq 'usbhid') { #- FIXME: should not be hardcoded, use $_->{sysfs_device} . */usb:(hiddev\d+) #- the device should also be assigned to the ups user $_->{port} = "/dev/hiddev0"; $_->{driver} = 'hidups'; $_; } elsif ($_->{description} =~ /^MGE UPS Systems\|/ && $_->{driver} =~ /ups$/) { $_->{port} = "auto"; $_->{media_type} = 'UPS'; $_->{driver} = 'newhidups'; $_; } else { (); } } usb_probe()); } $pcitable_addons = <<'EOF'; # add here lines conforming the pcitable format (0xXXXX\t0xXXXX\t"\w+"\t".*") EOF $usbtable_addons = <<'EOF'; # add here lines conforming the usbtable format (0xXXXX\t0xXXXX\t"\w+"\t".*") EOF sub install_addons { my ($prefix) = @_; #- this test means install_addons can only be called after ldetect-lst has been installed. if (-d "$prefix/usr/share/ldetect-lst") { my $update = 0; foreach ([ 'pcitable.d', $pcitable_addons ], [ 'usbtable.d', $usbtable_addons ]) { my ($dir, $str) = @$_; -d "$prefix/usr/share/ldetect-lst/$dir" && $str =~ /^[^#]/m and $update = 1 and output "$prefix/usr/share/ldetect-lst/$dir/95drakx.lst", $str; } $update and run_program::rooted($prefix, "/usr/sbin/update-ldetect-lst"); } } sub add_addons { my ($addons, @l) = @_; foreach (split "\n", $addons) { /^\s/ and die qq(bad detect_devices::probeall_addons line "$_"); s/^#.*//; s/"(.*?)"/$1/g; next if /^$/; my ($vendor, $id, $driver, $description) = split("\t", $_, 4) or die qq(bad detect_devices::probeall_addons line "$_"); foreach (@l) { $_->{vendor} == hex $vendor && $_->{id} == hex $id or next; put_in_hash($_, { driver => $driver, description => $description }); } } @l; } my (@pci, @usb); sub pci_probe__real() { add_addons($pcitable_addons, map { my %l; @l{qw(vendor id subvendor subid pci_domain pci_bus pci_device pci_function media_type nice_media_type driver description)} = split "\t"; $l{$_} = hex $l{$_} foreach qw(vendor id subvendor subid); $l{bus} = 'PCI'; $l{sysfs_device} = sprintf('/sys/bus/pci/devices/%04x:%02x:%02x.%d', $l{pci_domain}, $l{pci_bus}, $l{pci_device}, $l{pci_function}); \%l; } c::pci_probe()); } sub pci_probe() { @pci = pci_probe__real() if !@pci; @pci; } sub usb_probe__real() { -e "/proc/bus/usb/devices" or return; add_addons($usbtable_addons, map { my %l; @l{qw(vendor id media_type driver description pci_bus pci_device)} = split "\t"; $l{media_type} = join('|', grep { $_ ne '(null)' } split('\|', $l{media_type})); $l{$_} = hex $l{$_} foreach qw(vendor id); $l{sysfs_device} = "/sys/class/usb_device/usbdev$l{pci_bus}.$l{pci_device}/device"; $l{bus} = 'USB'; \%l; } c::usb_probe()); } sub usb_probe() { if ($::isStandalone && @usb) { @usb; } else { @usb = usb_probe__real(); } } sub firewire_probe() { my $dev_dir = '/sys/bus/ieee1394/devices'; my @l = map { my $dir = "$dev_dir/$_"; my $get = sub { chomp_(cat_($_[0])) }; { version => hex($get->("$dir/../vendor_id")), specifier_id => hex($get->("$dir/specifier_id")), specifier_version => hex($get->("$dir/version")), bus => 'Firewire', sysfs_device => $dir, }; } grep { -f "$dev_dir/$_/specifier_id" } all($dev_dir); my $e; foreach (cat_('/proc/bus/ieee1394/devices')) { if (m!Vendor/Model ID: (.*) \[(\w+)\] / (.*) \[(\w+)\]!) { push @l, $e = { vendor => hex($2), id => hex($4), description => join('|', $1, $3), bus => 'Firewire', }; } elsif (/Software Specifier ID: (\w+)/) { $e->{specifier_id} = hex $1; } elsif (/Software Version: (\w+)/) { $e->{specifier_version} = hex $1; } } foreach (@l) { if ($_->{specifier_id} == 0x00609e && $_->{specifier_version} == 0x010483) { add2hash($_, { driver => 'sbp2', description => "Generic Firewire Storage Controller" }); } elsif ($_->{specifier_id} == 0x00005e && $_->{specifier_version} == 0x000001) { add2hash($_, { driver => 'eth1394', description => "IEEE 1394 IPv4 Driver (IPv4-over-1394 as per RFC 2734)" }); } } @l; } sub pcmcia_controller_probe() { my ($controller) = probe_category('bus/pcmcia'); if (!$controller && !$::testing && !$::noauto && arch() =~ /i.86/) { my $driver = c::pcmcia_probe(); $controller = { driver => $driver, description => "PCMCIA controller ($driver)" } if $driver; } $controller; } sub pcmcia_probe() { require modalias; require modules; my $dev_dir = '/sys/bus/pcmcia/devices'; map { my $dir = "$dev_dir/$_"; my $get = sub { chomp_(cat_("$dir/$_[0]")) }; my $class_dev = first(glob_("$dir/tty*")); my $device = $class_dev && get_sysfs_field_from_link($dir, basename($class_dev)); my $modalias = $get->('modalias'); my $driver = get_sysfs_field_from_link($dir, 'driver'); #- fallback on modalias result #- but only if the module isn't loaded yet (else, it would already be binded) #- this prevents from guessing the wrong driver for multi-function devices my $module = $modalias && first(modalias::get_modules($modalias)); $driver ||= !member($module, modules::loaded_modules()) && $module; { description => join(' ', grep { $_ } map { $get->("prod_id$_") } 1 .. 4), driver => $driver, if_($modalias, modalias => $modalias), if_($device, device => $device), bus => 'PCMCIA', sysfs_device => $dir, }; } all($dev_dir); } my $dmi_probe; sub dmi_probe() { $dmi_probe ||= [ map { /(.*?)\t(.*)/ && { bus => 'DMI', driver => $1, description => $2 }; } $> ? () : c::dmi_probe() ]; @$dmi_probe; } # pcmcia_probe provides field "device", used in network.pm # => probeall with $probe_type is unsafe sub probeall() { return if $::noauto; pci_probe(), usb_probe(), firewire_probe(), pcmcia_probe(), dmi_probe(); } sub probeall_update_cache() { return if $::noauto; @pci = pci_probe__real(), @usb = usb_probe__real(), firewire_probe(), pcmcia_probe(), dmi_probe(); } sub matching_desc__regexp { my ($regexp) = @_; grep { $_->{description} =~ /$regexp/i } probeall(); } sub matching_driver__regexp { my ($regexp) = @_; grep { $_->{driver} =~ /$regexp/i } probeall(); } sub matching_driver { my (@list) = @_; grep { member($_->{driver}, @list) } probeall(); } sub probe_name { my ($name) = @_; map { $_->{driver} =~ /^$name:(.*)/ } probeall(); } sub probe_unique_name { my ($name) = @_; my @l = uniq(probe_name($name)); if (@l > 1) { log::l("oops, more than one $name from probe: ", join(' ', @l)); } $l[0]; } sub stringlist { my ($b_verbose) = @_; map { my $ids = $b_verbose || $_->{description} eq '(null)' ? sprintf("vendor:%04x device:%04x", $_->{vendor}, $_->{id}) : ''; my $subids = $_->{subid} && $_->{subid} != 0xffff ? sprintf("subv:%04x subd:%04x", $_->{subvendor}, $_->{subid}) : ''; sprintf("%-16s: %s%s%s", $_->{driver} || 'unknown', $_->{description}, $_->{media_type} ? sprintf(" [%s]", $_->{media_type}) : '', $ids || $subids ? " ($ids" . ($ids && $subids && " ") . "$subids)" : '', ); } probeall(); } sub tryOpen($) { my $F; sysopen($F, devices::make($_[0]), c::O_NONBLOCK()) && $F; } sub tryWrite($) { my $F; sysopen($F, devices::make($_[0]), 1 | c::O_NONBLOCK()) && $F; } my @dmesg; sub syslog() { if (-r "/tmp/syslog") { map { /<\d+>(.*)/ } cat_("/tmp/syslog"); } else { @dmesg = `/bin/dmesg` if !@dmesg; @dmesg; } } sub get_mac_model() { my $mac_model = cat_("/proc/device-tree/model") || die "Can not open /proc/device-tree/model"; log::l("Mac model: $mac_model"); $mac_model; } sub get_mac_generation() { cat_('/proc/cpuinfo') =~ /^pmac-generation\s*:\s*(.*)/m ? $1 : "Unknown Generation"; } sub hasSMP() { return if $::testing; (any { /NR_CPUS limit of 1 reached/ } syslog()) || any { /\bProcessor #(\d+)\s+(\S*)/ && $1 > 0 && $2 ne 'invalid' } syslog(); } sub hasPCMCIA() { $::o->{pcmcia} } #- because /proc/pcmcia seems not to be present on 2.4 at least (or use /var/run/stab) my (@dmis, $dmidecode_already_runned); # we return a list b/c several DMIs have the same name: sub dmidecode() { return @dmis if $dmidecode_already_runned; return if $>; my ($ver, @l) = run_program::get_stdout('dmidecode'); my $tab = "\t"; if ($ver =~ /(\d+\.\d+)/ && $1 >= 2.7) { #- new dmidecode output is less indented $tab = ''; #- drop header shift @l while @l && $l[0] ne "\n"; } foreach (@l) { if (/^$tab\t(.*)/) { $dmis[-1]{string} .= "$1\n"; $dmis[-1]{$1} = $2 if /^$tab\t(.*): (.*)$/; } elsif (my ($s) = /^$tab(.*)/) { next if $s =~ /^$/ || $s =~ /\bDMI type \d+/; $s =~ s/ Information$//; push @dmis, { name => $s }; } } $dmidecode_already_runned = 1; @dmis; } sub dmidecode_category { my ($cat) = @_; my @l = grep { $_->{name} eq $cat } dmidecode(); wantarray() ? @l : $l[0] || {}; } #- size in MB sub dmi_detect_memory() { my @l1 = map { $_->{'Enabled Size'} =~ /(\d+) MB/ && $1 } dmidecode_category('Memory Module'); my @l2 = map { $_->{'Form Factor'} =~ /^(SIMM|SIP|DIP|DIMM|RIMM|SODIMM|SRIMM)$/ && ($_->{Size} =~ /(\d+) MB/ && $1 || $_->{Size} =~ /(\d+) kB/ && $1 * 1024); } dmidecode_category('Memory Device'); max(sum(@l1), sum(@l2)); } sub computer_info() { my $Chassis = dmidecode_category('Chassis')->{Type} =~ /(\S+)/ && $1; my $date = dmidecode_category('BIOS')->{'Release Date'} || ''; my $BIOS_Year = $date =~ m!(\d{4})! && $1 || $date =~ m!\d\d/\d\d/(\d\d)! && "20$1"; +{ isLaptop => member($Chassis, 'Portable', 'Laptop', 'Notebook', 'Hand Held', 'Sub Notebook', 'Docking Station'), if_($BIOS_Year, BIOS_Year => $BIOS_Year), }; } #- try to detect a laptop, we assume pcmcia service is an indication of a laptop or #- the following regexp to match graphics card apparently only used for such systems. sub isLaptop() { arch() =~ /ppc/ ? get_mac_model() =~ /Book/ : computer_info()->{isLaptop} || glob_("/sys/bus/acpi/devices/PNP0C0D:*") #- ACPI lid button || (matching_desc__regexp('C&T.*655[45]\d') || matching_desc__regexp('C&T.*68554') || matching_desc__regexp('Neomagic.*Magic(Media|Graph)') || matching_desc__regexp('ViRGE.MX') || matching_desc__regexp('S3.*Savage.*[IM]X') || matching_desc__regexp('Intel Corporation\|Mobile') || matching_desc__regexp('\bATI\b.*(Mobility|\bLT\b)')) || (any { $_->{'model name'} =~ /\b(mobile|C7-M)\b/i } getCPUs()) || probe_unique_name("Type") eq 'laptop' #- ipw2100/2200/3945 are Mini-PCI (Express) adapters || (any { member($_->{driver}, qw(ipw2100 ipw2200 ipw3945)) } pci_probe()); } sub BIGMEM() { arch() !~ /x86_64|ia64/ && $> == 0 && dmi_detect_memory() > 4 * 1024; } sub is_i586() { my $cpuinfo = cat_('/proc/cpuinfo'); $cpuinfo =~ /^cpu family\s*:\s*(\d+)/m && $1 < 6 || $cpuinfo =~ /^model name\s*:\s*Transmeta.* TM5800/m || # mdvbz#37866 !has_cpu_flag('cmov'); } sub is_xbox() { any { $_->{vendor} == 0x10de && $_->{id} == 0x02a5 } pci_probe(); } sub is_virtualbox() { any { $_->{driver} eq 'vboxadd' } detect_devices::pci_probe(); } sub has_cpu_flag { my ($flag) = @_; cat_('/proc/cpuinfo') =~ /^flags.*\b$flag\b/m; } sub matching_types() { +{ laptop => isLaptop(), '64bit' => to_bool(arch() =~ /64/), wireless => to_bool(get_wireless_interface() || probe_category('network/wireless')), }; } sub hasWacom() { find { $_->{vendor} == 0x056a || $_->{driver} =~ /wacom/ } usb_probe() } sub usbWacom() { grep { $_->{vendor} eq '056a' } getInputDevices() } sub usbKeyboards() { grep { $_->{media_type} =~ /\|Keyboard/ } usb_probe() } sub usbStorage() { grep { $_->{media_type} =~ /Mass Storage\|/ } usb_probe() } sub has_mesh() { find { /mesh/ } all_files_rec("/proc/device-tree") } sub has_53c94() { find { /53c94/ } all_files_rec("/proc/device-tree") } sub usbKeyboard2country_code { my ($usb_kbd) = @_; my ($F, $tmp); sysopen($F, sprintf("/proc/bus/usb/%03d/%03d", $usb_kbd->{pci_bus}, $usb_kbd->{pci_device}), 0) and sysseek $F, 0x28, 0 and sysread $F, $tmp, 1 and unpack("C", $tmp); } sub probeSerialDevices() { require list_modules; require modules; modules::append_to_modules_loaded_at_startup_for_all_kernels(modules::load_category($::o->{modules_conf}, 'various/serial')); foreach (0..3) { #- make sure the device are created before probing, devices::make("/dev/ttyS$_"); #- and make sure the device is a real terminal (major is 4). int((stat "/dev/ttyS$_")[6]/256) == 4 or $serialprobe{"/dev/ttyS$_"} = undef; } #- for device already probed, we can safely (assuming device are #- not moved during install :-) #- include /dev/mouse device if using an X server. mkdir_p("/var/lock"); -l "/dev/mouse" and $serialprobe{"/dev/" . readlink "/dev/mouse"} = undef; foreach (keys %serialprobe) { m|^/dev/(.*)| and touch "/var/lock/LCK..$1" } print STDERR "Please wait while probing serial ports...\n"; #- start probing all serial ports... really faster than before ... #- ... but still take some time :-) my %current; foreach (run_program::get_stdout('serial_probe')) { if (/^\s*$/) { $serialprobe{$current{DEVICE}} = { %current } if $current{DEVICE}; %current = (); } elsif (/^([^=]+)=(.*?)\s*$/) { $current{$1} = $2; } } foreach (values %serialprobe) { $_->{DESCRIPTION} =~ /modem/i and $_->{CLASS} = 'MODEM'; #- hack to make sure a modem is detected. $_->{DESCRIPTION} =~ /olitec/i and $_->{CLASS} = 'MODEM'; #- hack to make sure such modem gets detected. log::l("probed $_->{DESCRIPTION} of class $_->{CLASS} on device $_->{DEVICE}"); } } sub probeSerial($) { $serialprobe{$_[0]} } sub hasModem($) { $serialprobe{$_[0]} && $serialprobe{$_[0]}{CLASS} eq 'MODEM' && $serialprobe{$_[0]}{DESCRIPTION}; } sub hasMousePS2 { my $t; sysread(tryOpen($_[0]) || return, $t, 256) != 1 || $t ne "\xFE"; } sub probeall_unavailable_modules { map { my $driver = $_->{driver}; $driver !~ /:/ && !member($driver, 'hub', 'unknown', 'amd64_agp') && !modules::module_is_available($driver) ? $driver : (); } probeall(); } sub probeall_dkms_modules { my @unavailable_modules = probeall_unavailable_modules() or return; require modalias; my $dkms_modules = modalias::parse_file_modules($::prefix . "/usr/share/ldetect-lst/dkms-modules.alias"); intersection([ keys(%$dkms_modules) ], \@unavailable_modules); } sub usb_description2removable { local ($_) = @_; return 'camera' if /\bcamera\b/i; return 'memory_card' if /\bmemory\s?stick\b/i || /\bcompact\s?flash\b/i || /\bsmart\s?media\b/i; return 'memory_card' if /DiskOnKey/i || /IBM-DMDM/i; return 'zip' if /\bzip\s?(100|250|750)/i; return 'floppy' if /\bLS-?120\b/i; return; } sub usb2removable { my ($e) = @_; $e->{usb_driver} or return; if ($e->{usb_driver} =~ /Removable:(.*)/) { return $1; } elsif (my $name = usb_description2removable($e->{usb_description})) { return $name; } undef; } sub suggest_mount_point { my ($e) = @_; my $name = $e->{media_type}; if (member($e->{media_type}, 'hd', 'fd')) { if (exists $e->{usb_driver}) { $name = usb2removable($e) || 'removable'; } elsif (isZipDrive($e)) { $name = 'zip'; } elsif ($e->{media_type} eq 'fd') { $name = 'floppy'; } else { log::l("suggest_mount_point: do not know what to with hd $e->{device}"); } } $name; } 1; #- Local Variables: #- mode:cperl #- tab-width:8 #- End: