!! USE WITH CARE !! Goal of duplication is to easily deploy a computer over network without taking care of numbers of computer. In this documentation, we call golden node the node we want to clone. We can duplicate SCSI or IDE hard drive, and duplication support multiple filesystem (reiserfs, ext2, ext3, ext4, xfs, jfs). This method came from a very old project called CLIC, and was used under IGGI project, all Mandrake Clustering products, and now it is used under XtreemOS project. Now it should be available in 2010 spring, and all futur product. WARNING: all data on client nodes will be ERASED ! We duplicate partitions of HDD's golden node, and the process will do an fdisk command on the client node, so ALL YOUR DATA will be erased on client nodes. With KA method you can quickly duplicate a node using a desc file describing partitions. KA method only duplicate data on partitions, so if you have 80go HDD disk, and only 10go on it, KA only duplicates 10go, and not the whole disk. KA method doesn't not support RAID software. Drawbacks: KA method doesn't support RAID software (use dolly to do that) all data on client nodes are erased you need a PXE, DHDCP and TFTP server you must re-create same partition table as the golden node (even if size can differ) even if it has been tested, it's still an experimental method cloning script are old, and need a full rewrite now it's only works with the Mageia installer (need to patch it to support a KA method) if a node crash while doing a duplication, the duplication process stop (or became very unstable) using fdisk to erase and re-format the HDD is not a good way to proceed UUID support is not really done (fstab use old /dec/sdX) you can only clone Linux filesystems (if you want to duplicate another kinf of FS, it's up to you to modify the scripts) of course various other things ! The clone process works in three steps PXE boot to retrieve stage1: the computer boot on PXE mode, retrieve vmlinuz and an initrd image. The computer is in stage1 mode, and is able to get the stage2 throug KA. Network is up. get stage2: the computer gets the stage2 with the KA method. The stage2 contains all necessary tools to recognize your hardware (the most important things is to detect your HDD and your network card), and all necessary tools/scripts to finalize the cloning process. Duplication process: the computer auto-probes needed modules to be able to access the HDD. A basic log server is launched on the client node to be able to run command and get status of the KA duplication process. The computer reconfigure the modprobe.conf and restore the booloader (grub or lilo) All needed files are available in Mageia cooker. install/stage2/rescue.sqfs: this is the stage2 file with all needed files to detect and probe modules, and launch the third step of the duplication process. This file will be used on the golden node. isolinux/alt0/vmlinuz: linux kernel, needed in the /var/lib/tftpboot/X86PC/linux/images/ directory of the PXE server isolinux/alt0/all.rdz: stage1 and all needed modules and tools. To easily clone a computer node, we use PXE technology to boot a kernel, and an initrd image wich contains all needed modules for network and media storage. Documentation about PXE can be found here: PXE doc. Please, keep in mind setting such services can DISTURB your current network architecture. Mageia installer supports various methods to install a computer. With PXE configuration file you can specify wich method you want to use to install your node, or add a specific option at boot prompt. Edit your default PXE configuration file to add your custom entry (/var/lib/tftpboot/X86PC/linux/pxelinux.cfg/default). PROMPT 1 DEFAULT local DISPLAY messages TIMEOUT 50 F1 help.txt label local LOCALBOOT 0 label kamethod KERNEL images/vmlinuz APPEND initrd=images/all.rdz ramdisk_size=64000 vga=788 \ automatic=method:ka,interface:eth0,network:dhcp root=/dev/ram3 rw kamethod At boot prompt no you can boot: DEFAULT local: default boot will be local one, change it with the name of a LABEL local: boot local kamethod: automatic mode, get stage2 through KA. Network interface is set to eth0. Auto setup the network with DHCP, and use the KA technology to launch the replication method. TFTP server should be activated in /etc/xinetd.d/tftp file, and the xinetd service started. service tftp { disable= no socket_type= dgram protocol= udp wait= yes user= root server= /usr/sbin/in.tftpd server_args = -s /var/lib/tftpboot per_source= 11 cps= 100 2 flags= IPv4 } ,,,, service=X86PC,0,2,linux,Mageia x86 service=IA64PC,0,2,linux,Mageia IA64 service=X86PC,0,0,local,Local boot # tftpd base dir tftpdbase=/ # domain=guibland.com domain= ]]> IE of an /etc/dhcpd.conf configuration file. Change IPADDR_TFTP with the IP address of the TFTP serrver, and the NET value. Don't forget to adjust the domain-name and the domain-name-servers. ddns-update-style none; allow booting; allow bootp; authoritative; # Definition of PXE-specific options # Code 1: Multicast IP address of bootfile # Code 2: UDP port that client should monitor for MTFTP responses # Code 3: UDP port that MTFTP servers are using to listen for MTFTP requests # Code 4: Number of secondes a client must listen for activity before trying # to start a new MTFTP transfer # Code 5: Number of secondes a client must listen before trying to restart # a MTFTP transfer # define Option for the PXE class option space PXE; option PXE.mtftp-ip code 1 = ip-address; option PXE.mtftp-cport code 2 = unsigned integer 16; option PXE.mtftp-sport code 3 = unsigned integer 16; option PXE.mtftp-tmout code 4 = unsigned integer 8; option PXE.mtftp-delay code 5 = unsigned integer 8; option PXE.discovery-control code 6 = unsigned integer 8; option PXE.discovery-mcast-addr code 7 = ip-address; #Define options for pxelinux option space pxelinux; option pxelinux.magic code 208 = string; option pxelinux.configfile code 209 = text; option pxelinux.pathprefix code 210 = text; option pxelinux.reboottime code 211 = unsigned integer 32; site-option-space "pxelinux"; option pxelinux.magic f1:00:74:7e; option pxelinux.reboottime 30; #Class that determine the options for Etherboot 5.x requests class "Etherboot" { #if The vendor-class-identifier equal Etherboot-5.0 match if substring (option vendor-class-identifier, 0, 13) = "Etherboot-5.0"; # filename define the file retrieve by the client, there nbgrub # our tftp is chrooted so is just the path to the file filename "/etherboot/nbgrub"; #Used by etherboot to detect a valid pxe dhcp server option vendor-encapsulated-options 3c:09:45:74:68:65:72:62:6f:6f:74:ff; # Set the "vendor-class-identifier" field to "PXEClient" in dhcp answer # if this field is not set the pxe client will ignore the answer ! option vendor-class-identifier "Etherboot-5.0"; vendor-option-space PXE; option PXE.mtftp-ip 0.0.0.0; # IP of you TFTP server next-server IPADDR_TFTP; } # create the Class PXE class "PXE" { # if the "vendor-class-identifier" is set to "PXEClient" in the client dhcp request match if substring(option vendor-class-identifier, 0, 9) = "PXEClient"; filename "/X86PC/linux/linux.0"; option vendor-class-identifier "PXEClient"; vendor-option-space PXE; option PXE.mtftp-ip 0.0.0.0; next-server IPADDR_TFTP; } #host node20 { # hardware ethernet 00:40:CA:8C:B6:E9; # fixed-address node20; #} subnet NET.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; option routers IPADDR_GW; default-lease-time 288000; max-lease-time 864000; option domain-name "guibland.com"; option domain-name-servers IPADDR_DNS; next-server IPADDR_TFTP; pool { range NET.30 NET.40; } } You need the rescue disk (wich contains the /ka directory), Just extract this file, and copy all directory in /mnt/ka. [root@guibpiv ~]# mkdir /mnt/ka [root@guibpiv ~]# cd /mnt/ka/ [root@guibpiv ka]# unsquashfs rescue.sqfs [root@guibpiv ka]# mv squashfs-root/* . [root@guibpiv ka]# ls bin/ dev/ etc/ ka/ lib/ modules/ proc/ sbin/ squashfs-root/ tmp/ usr/ var/ Go in the /mnt/ka/ka directory, and see all new files available. All those files are needed to do a KA duplication process. We will explain now the rule of each of them. You can modify all them, those files will be copied in the directory /tmp/stage2 of the client node of the duplication process (second step). This is the master script to declare a node as a golden node. This script takes a lot of arguments. This script should be run on the host wich have the /mnt/ka directory. -h, --help : display this message -n num : specify the number of (destination) nodes -x dir : exclude directory -X sdb|sdc : exclude sdb for the replication -m drive : copy the master boot record (for windows) of this drive (not really tested yet) -M drive file : use 'file' as master boot record (must be 446 bytes long) for the specified drive -D partition : also copy partition 'partition' -p drive pdesc : use 'pdesc' file as partition scheme (see doc) for the specified drive -d delay : delay beteween the release of 2 clients (1/10 second) -r 'grub|lilo' : choose the bootloader (you can add mkinitrd options) ie: ka-d.sh -n 3 -p sda /tmp/desc -X 'sdb|sdc' -r 'grub --with=ata_piix --with=piix' This file contains all variables needed by other scripts. It also tries to get information like IP address. This script generate the description table of the hard drive disk in the /tmp/desc file. This file must follow some rules: one line per partition, with two fields : type of partition and size in megabytes. The type can be linux, swap, extended. Other types can be obtained by appending their hexadecimal number to 'type'. For example linux is the same as type83. The size is either a number of megabytes, or the keyword fill (to take all available space). The logical partitions must have the logical keyword. Do a man ka-d for more help. This script creates a basic output like the content of the/etc/modprobe.conf file. Drawbacks this file must be updated for each new modules available in the kernel (based on the kernel/list_modules.pm file). The ka-d-client binary file is used to get stage2 with the KA method, and after get the whole system. The important argument is the -s session name. A KA can only connect to a specific session (getstage2, kainstall ...). The code source is available in the ka-deploy SRPM. The ka-d-server binary file is used to be a KA golden node server. Like the ka-d-client the session arguments is an important parameter (-s session_name). The session name will be getstage2 to retrieve the stage2 (after the PXE boot) and will be kainstall1 at duplication process step. If you want to do more than one duplication process of nodes at the same time, you should synchronize the ka_sesion name between the server and the client. The code source is available in the ka-deploy SRPM. Script launched on the KA client (after getting stage2 and probing modules), to do the full process of the Ka duplication. This script call other scripts to prepare the node (prepare_node.sh), configure the bootloader (make_initrd_grub or make_initrd_lilo). Basic script to store the log of the KA duplication process on an FTP server. Adjust to feet your need, and uncomment the line #store_log.sh in the /mnt/ka/ka/ka_replication.sh file. Script to set bootable an HDD using fdisk. First arg must be the HDD device. Restore and reload the Grub bootloader in the /mnt/disk directory. It's a very basic script, and perhaps use the restore_bootloader of the Mageia Rescue should be a better idea. Restore and reload the lilo bootloader in the /mnt/disk directory. Again it's a very basic script, perhaps we should use the restore_bootloader of the Mageia Rescue. This script remove in the futur system the old network's udev rules, old dhcp cache files, launch the script gen_modprobe_conf.pl to regenerate an up to date /etc/modprobe.conf in the new system, and launch the script to restore the bootloader. If you want to do more action on the installed, system, you can modify this script. Very basic perl script to open the port 12345, and paste the content of the /tmp/ka* file. It also permit the execution of commands on node, if user send a message from the golden node with the exec prefix. Script to connect to a client node, first arg must be the IP address of the node. You can run command on the node with the exec prefix. Now, it is time to build a description of the node partitions. You can use the script /mnt/ka/ka/fdisk_to_desc as root user, or your favorite text editor, you can write a file like this one: linux 3500 extended fill logical swap 500 logical linux fill This file describes your partition table and the sample above can be considered as a default one for a recommended installation. There is a 3.5GB / partition, a 500 MB swap partition, and /var fills the rest, of course you can adjust sizes accoding to your system. Type the following to start the ka replication server as root user on the golden node: -r "grub --with=jfs --with=ata_piix": use grub bootloader and --with=jfs --with=piix mkinitrd option in the chrooted system after the KA deploiement -n nb_nodes: specify how many nodes are clients -p sda desc: specify the name of the hdd -x /tmp: exclude /tmp directory -X sdb: exclude sdb hdd for the duplication Now the golden node is waiting for clients nodes to start replication. We have to configure the PXE to boot by default on kamethod. To do this just edit /var/lib/tftpboot/X86PC/linux/pxelinux.cfg/default and set DEFAULT to kamethod: DEFAULT kamethod So, next time a node boots, the PXE server will force the node to boot using the kamethod entry. Now, you boot all remaining nodes. The replication process will start once all nodes are up and waiting on the KA screen. If the nodes can't reach the golden node, running the KA server the message Can't reach a valid KA server will appear. Each node will try five times to reach the KA server, after that the node will reboot. As the node boots on kamethod, it will retry until it finds it. Once all the nodes have found the KA server, the first duplication process will start. This step duplicates the stage2 from the /mnt/ka directory of the golden node, in the client's nodes memory (/dev/ram3 formated as ext2). Then, nodes chroot their memories (the /tmp/stage2 directory), and launch the drvinst command from the stage2, to probe all needed their modules (drivers). Then, the second step of the duplication starts. The duplication process will clone your drives following the description you have made (/tmp/desc of the golden node). Nodes will rewrite their partition table, then format their filesystems (ReiserFs, XFS, ext2/3/4, JFS). All new partitions will be mounted in the /mnt/disk directory. Then, the drive duplication process will begin. On a fast Ethernet switch you can reach speeds of 10MBytes/sec. At the end of the duplication process, each node will chroot its partitions and rebuild its /boot/initrd.img, and /etc/modprobe.conf files. This step ensures that your node will reboot using its potential SCSI drives and adjusting its network card driver. Before rebooting, each node reinstalls lilo/grub. All your node are now ready, and are clone of master node. Don't forget to change the default PXE boot to local so node after replication will boot localy. We will use a PIV 3gz box as golden node, with a SATA hard drive, and an Intel 82540EM Gigabit Ethernet Controller card. This golden box will be the: PXE, DHCPD, TFTP server. Client nodes are basic PIV 2.8gz, with a Realtek Semiconductor 8139 network card, and a IDE hard drive disk PE2650 dual XEON 2.4gz, SCSI Hard Drive disk, and NetXtreme BCM5701 Gigabit Ethernet cards Both nodes are configured to boot on their network card. Prepapre the golden node, install all needed tools. Create the /mnt/ka directory, and put all stuff in it (this directory will be sent to all client nodes and use to finish the duplication process) cd pub/linux/Mageia/distrib/cauldron/i586/install/stage2/ lftp distrib-coffee.ipsl.jussieu.fr:/pub/linux/Mageia/distrib/cauldron/i586/install/stage2> pget rescue.sqfs 19132416 bytes transferred in 78 seconds (241.1K/s) [root@localhost ~]# urpmi squashfs-tools http://192.168.1.253/cooker/i586/media/main/release/squashfs-tools-4.0-3.20091221.1mdv2010.1.i586.rpm installing squashfs-tools-4.0-3.20091221.1mdv2010.1.i586.rpm from /var/cache/urpmi/rpms Preparing... ############################################################################ 1/1: squashfs-tools ############################################################################ [root@localhost ~]# unsquashfs rescue.sqfs Parallel unsquashfs: Using 2 processors 988 inodes (1222 blocks) to write [============================================================================================-] 1222/1222 100% created 550 files created 93 directories created 60 symlinks created 371 devices created 1 fifos [root@localhost ~]# cd squashfs-root/ [root@localhost squashfs-root]# ls bin/ dev/ etc/ ka/ lib/ modules/ proc/ sbin/ tmp/ usr/ var/ [root@localhost squashfs-root]# mv * /mnt/ka/ ]]> Install all needed packages to be able to be a PXE, DHCPD and TFTP server Configure all services mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:17:31:19:a0:78 brd ff:ff:ff:ff:ff:ff inet 10.0.1.42/24 brd 10.0.1.255 scope global eth0 inet6 fe80::217:31ff:fe19:a078/64 scope link valid_lft forever preferred_lft forever [root@localhost ~]# vi /etc/pxe.conf # which interface to use interface=eth0 default_address=10.0.1.42 # the multicast ip address to listen on multicast_address=224.0.1.2 # mtftp info mtftp_address=10.0.1.42 mtftp_client_port=1758 mtftp_server_port=1759 # the port to listen on listen_port=4011 # enable multicast? use_multicast=1 # enable broadcast? use_broadcast=0 # user prompt prompt=Press F8 to view menu ... prompt_timeout=2 # what services to provide, priority in ordering # CSA = Client System Architecture # service=,,,, service=X86PC,0,2,linux,Mageia x86 service=IA64PC,0,2,linux,Mageia IA64 service=X86PC,0,0,local,Local boot # tftpd base dir tftpdbase=/ # domain name domain=guibland.com [root@localhost ~]# vi /etc/xinetd.d/tftp service tftp { disable = no socket_type = dgram protocol = udp wait = yes user = root server = /usr/sbin/in.tftpd server_args = -s /var/lib/tftpboot per_source = 11 cps = 100 2 flags = IPv4 } [root@localhost ~]# cp /etc/dhcpd.conf.pxe.single /etc/dhcpd.conf cp: overwrite `/etc/dhcpd.conf'? y [root@localhost ~]# cat /etc/resolv.conf nameserver 10.0.1.253 search guibland.com [root@localhost ~]# cat /etc/dhcpd.conf # for explanation in french go to : http://www.delafond.org/traducmanfr/man/man5/dhcpd.conf.5.html ddns-update-style none; allow booting; allow bootp; # Your dhcp server is not master on your network ! #not authoritative; # Your dhcpd server is master on your network ! #authoritative; authoritative; #Interface where dhcpd is active #DHCPD_INTERFACE = "eth0"; # Definition of PXE-specific options # Code 1: Multicast IP address of bootfile # Code 2: UDP port that client should monitor for MTFTP responses # Code 3: UDP port that MTFTP servers are using to listen for MTFTP requests # Code 4: Number of secondes a client must listen for activity before trying # to start a new MTFTP transfer # Code 5: Number of secondes a client must listen before trying to restart # a MTFTP transfer # define Option for the PXE class option space PXE; option PXE.mtftp-ip code 1 = ip-address; option PXE.mtftp-cport code 2 = unsigned integer 16; option PXE.mtftp-sport code 3 = unsigned integer 16; option PXE.mtftp-tmout code 4 = unsigned integer 8; option PXE.mtftp-delay code 5 = unsigned integer 8; option PXE.discovery-control code 6 = unsigned integer 8; option PXE.discovery-mcast-addr code 7 = ip-address; #Define options for pxelinux option space pxelinux; option pxelinux.magic code 208 = string; option pxelinux.configfile code 209 = text; option pxelinux.pathprefix code 210 = text; option pxelinux.reboottime code 211 = unsigned integer 32; site-option-space "pxelinux"; # These lines should be customized to your setup #option pxelinux.configfile "configs/common"; #option pxelinux.pathprefix "/pxelinux/files/"; #filename "/pxelinux/pxelinux.bin"; option pxelinux.magic f1:00:74:7e; option pxelinux.reboottime 30; #if exists dhcp-parameter-request-list { # Always send the PXELINUX options # append dhcp-parameter-request-list 208, 209, 210, 211; # append dhcp-parameter-request-list 208,211; # } #Class that determine the options for Etherboot 5.x requests class "Etherboot" { #if The vendor-class-identifier equal Etherboot-5.0 match if substring (option vendor-class-identifier, 0, 13) = "Etherboot-5.0"; # filename define the file retrieve by the client, there nbgrub # our tftp is chrooted so is just the path to the file filename "/etherboot/nbgrub"; #Used by etherboot to detect a valid pxe dhcp server option vendor-encapsulated-options 3c:09:45:74:68:65:72:62:6f:6f:74:ff; # Set the "vendor-class-identifier" field to "PXEClient" in dhcp answer # if this field is not set the pxe client will ignore the answer ! option vendor-class-identifier "Etherboot-5.0"; vendor-option-space PXE; option PXE.mtftp-ip 0.0.0.0; # IP of you TFTP server next-server 10.0.1.42; } # create the Class PXE class "PXE" { # if the "vendor-class-identifier" is set to "PXEClient" in the client dhcp request match if substring(option vendor-class-identifier, 0, 9) = "PXEClient"; # filename define the file retrieve by the client, there pxelinux.0 # our tftp is chrooted so is just the path to the file # If you prefer use grub, use pxegrub compiled for your ethernet card. #filename "/PXEClient/pxegrub"; filename "/X86PC/linux/linux.0"; # Set the "vendor-class-identifier" field to "PXEClient" in dhcp answer # if this field is not set the pxe client will ignore the answer ! option vendor-class-identifier "PXEClient"; vendor-option-space PXE; option PXE.mtftp-ip 0.0.0.0; # IP of you TFTP server next-server 10.0.1.42; } # Tags uses by dhcpnode and setup_add_nodes_to_dhcp # TAG: NODE_LIST_ADMIN_BEGIN # TAG: NODE_LIST_ADMIN_END # TAG: MY_ADMIN_BEGIN subnet 10.0.1.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; option routers 10.0.1.253; default-lease-time 288000; max-lease-time 864000; option domain-name "guibland.com"; option domain-name-servers 10.0.1.253; next-server 10.0.1.42; pool { range 10.0.1.110 10.0.1.120; } } # TAG: MY_ADMIN_END [root@localhost ~]# service xinetd restart Stopping xinetd [FAILED] Starting xinetd [ OK ] [root@localhost ~]# service pxe restart Stopping PXE server [FAILED] Dhcp server is not running on this machine ! Be sure that a valid PXE Dhcp server is running on your network Starting PXE server [ OK ] [root@localhost ~]# service dhcpd restart Shutting down dhcpd: [ OK ] Starting dhcpd: [ OK ] ]]> KA listen only listen on eth0, and need a FQDN. So if it is not the case, ka-d-server will try to open a port on 0.0.0.0 IP address, wich cause an error. You can fix it easely setting an valid hostname in /etc/hosts file. Don't forget to kill ka-d-server with crtl+C key, after testing it will open a port on a valid IP address. =0' failed. Aborted [root@node42 ~]# cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 10.0.1.42 node42.guibland.com [root@node42 ~]# ka-d-server Compiled : May 4 2010 20:33:07 ARGS=+ka-d-server+ Server IP = 10.0.1.42 command = (cd /; tar --create --one-file-system --sparse /) I want 1 clients Socket 3 on port 30765 on node42.guibland.com ready. Socket 4 on port 30764 on node42.guibland.com ready. [root@node42 ~]# ^C ]]> We need to describe the partition table of our golden node, to send it to client nodes. Set default PXE boot to kamethod ls -rw-r--r-- 1 ftp ftp 15613654 Apr 23 17:26 all.rdz -rw-r--r-- 1 ftp ftp 2279584 Apr 23 17:26 vmlinuz lftp distrib-coffee.ipsl.jussieu.fr:/pub/linux/Mageia/distrib/cauldron/i586/isolinux/alt0> mget * 17893238 bytes transferred in 77 seconds (227.9K/s) Total 2 files transferred lftp distrib-coffee.ipsl.jussieu.fr:/pub/linux/Mageia/distrib/cauldron/i586/isolinux/alt0> [root@node42 images]# pwd /var/lib/tftpboot/X86PC/linux/images [root@node42 images]# ls all.rdz vmlinuz ]]> Now it's time to launch the duplication process `/tmp/ka-d3156/pfstab.tmp' + Mount points : /dev/sda2 / ext3 relatime 1 1 /dev/sda5 /home ext4 relatime 1 2 /dev/sda1 swap swap defaults 0 0 + Hard drives : sda + Reading partition table description for sda Added partition 1 : type 82 Added partition 2 : type 83 Added partition 5 : type 83 + Included mount points : / /home + Bootloader is: grub +++ Sending Stage2 +++ Compiled : May 4 2010 20:33:07 ARGS=+ka-d-server+-s+getstage2+-n+2+-e+(cd /mnt/ka; tar --create --one-file-system --sparse . )+ Server IP = 10.0.1.42 command = (cd /mnt/ka; tar --create --one-file-system --sparse . ) I want 2 clients Socket 4 on port 30765 on node42.guibland.com ready. Socket 5 on port 30764 on node42.guibland.com ready. got UDP packet from 10.0.1.111 Session name matches Sending UDP reply to 10.0.1.111 Accepting connection from 10.0.1.111 Clients : want_data 0 / connected 0 client says hello ! Client sends options Client accepts data got UDP packet from 10.0.1.110 Session name matches Sending UDP reply to 10.0.1.110 Accepting connection from 10.0.1.110 Clients : want_data 1 / connected 0 client says hello ! Client sends options Client accepts data Added client 10.0.1.110, daddy = 10.0.1.42 Added client 10.0.1.111, daddy = 10.0.1.110 Accepting connection from 10.0.1.110 checking connection auth10.0.1.42 reports 10.0.1.110 has opened data connection Client 10.0.1.110 reports data position : 0 10.0.1.42 reports 10.0.1.110 has been accepted Welcome son, you are number 1 (MAX 4) Client got client 10.0.1.110 reports 10.0.1.111 has opened data connection Client 10.0.1.111 reports data position : 0 sending auth for 10.0.1.111 to 10.0.1.110 Client got client 10.0.1.110 reports 10.0.1.111 has been accepted Let's go! Total data read = 43 Megs, BUF: 34M FREE = 0M startpos = 8MM End of data flow Dropping children Dropping child 10.0.1.110 All children dropped Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 1 -- connected : 2 Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 0 -- connected : 2 Peer closed connection on socket 7 close_connection(7) Busy clients: 0 -- connected : 1 Peer closed connection on socket 6 close_connection(6) Busy clients: 0 -- connected : 0 All clients left, I quit Total data sent = 44 Megs, in 1543 packets Transfer time = 0.858 seconds, throughput = 51.307 Mbytes/second The pipeline was emptied in 3.250 seconds - Sending partition/filesystem/mount points informations... +++ Running ka-deploy +++ Compiled : May 4 2010 20:33:07 ARGS=+ka-d-server+-s+kainstall1+-n+2+-e+(cd /tmp/ka-d3156 && tar c *)+ Server IP = 10.0.1.42 command = (cd /tmp/ka-d3156 && tar c *) I want 2 clients Socket 4 on port 30765 on node42.guibland.com ready. Socket 5 on port 30764 on node42.guibland.com ready. got UDP packet from 10.0.1.110 Session name matches Sending UDP reply to 10.0.1.110 Accepting connection from 10.0.1.110 Clients : want_data 0 / connected 0 client says hello ! Client sends options Client accepts data got UDP packet from 10.0.1.111 Session name matches Sending UDP reply to 10.0.1.111 Accepting connection from 10.0.1.111 Clients : want_data 1 / connected 0 client says hello ! Client sends options Client accepts data Added client 10.0.1.110, daddy = 10.0.1.42 Added client 10.0.1.111, daddy = 10.0.1.110 Accepting connection from 10.0.1.110 checking connection auth10.0.1.42 reports 10.0.1.110 has opened data connection Client 10.0.1.110 reports data position : 0 10.0.1.42 reports 10.0.1.110 has been accepted Welcome son, you are number 1 (MAX 4) Client got client 10.0.1.110 reports 10.0.1.111 has opened data connection Client 10.0.1.111 reports data position : 0 sending auth for 10.0.1.111 to 10.0.1.110 Client got client 10.0.1.110 reports 10.0.1.111 has been accepted Let's go! Total data read = 0 Megs, BUF: 0M FREE = 34M startpos = 0M End of data flow Dropping children Dropping child 10.0.1.110 All children dropped Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 1 -- connected : 2 Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 0 -- connected : 2 Peer closed connection on socket 6 close_connection(6) Busy clients: 0 -- connected : 1 Peer closed connection on socket 7 close_connection(7) Busy clients: 0 -- connected : 0 All clients left, I quit Total data sent = 0 Megs, in 1 packets Transfer time = 0.006 seconds, throughput = 1.698 Mbytes/second The pipeline was emptied in 0.038 seconds WAITING node (partition/format) - Sending Linux filesystem... +++ Running ka-deploy +++ Compiled : May 4 2010 20:33:07 ARGS=+ka-d-server+-s+kainstall2+-n+2+-e+(cd /; tar --create --one-file-system --sparse / /home)+ Server IP = 10.0.1.42 command = (cd /; tar --create --one-file-system --sparse / /home) I want 2 clients Socket 4 on port 30765 on node42.guibland.com ready. Socket 5 on port 30764 on node42.guibland.com ready. got UDP packet from 10.0.1.110 Session name matches Sending UDP reply to 10.0.1.110 Accepting connection from 10.0.1.110 Clients : want_data 0 / connected 0 client says hello ! Client sends options Client accepts data got UDP packet from 10.0.1.111 Session name matches Sending UDP reply to 10.0.1.111 Accepting connection from 10.0.1.111 Clients : want_data 1 / connected 0 client says hello ! Client sends options Client accepts data Added client 10.0.1.110, daddy = 10.0.1.42 Added client 10.0.1.111, daddy = 10.0.1.110 Accepting connection from 10.0.1.110 checking connection auth10.0.1.42 reports 10.0.1.110 has opened data connection Client got client 10.0.1.110 reports 10.0.1.111 has opened data connection Client 10.0.1.110 reports data position : 0 10.0.1.42 reports 10.0.1.110 has been accepted Welcome son, you are number 1 (MAX 4) Client 10.0.1.111 reports data position : 0 sending auth for 10.0.1.111 to 10.0.1.110 Client got client 10.0.1.110 reports 10.0.1.111 has been accepted Let's go! Total data read = 789 Megs, BUF: 34M FREE = 0M startpos = 754M End of data flow Dropping children Dropping child 10.0.1.110 All children dropped Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 1 -- connected : 2 Client says dad disconnected Client says he has finished Client has finished transfer Busy clients: 0 -- connected : 2 Peer closed connection on socket 7 close_connection(7) Busy clients: 0 -- connected : 1 Peer closed connection on socket 6 close_connection(6) Busy clients: 0 -- connected : 0 All clients left, I quit Total data sent = 792 Megs, in 25445 packets Transfer time = 69.904 seconds, throughput = 11.343 Mbytes/second The pipeline was emptied in 4.002 seconds ]]> To get the log of the client node, launch /mnt/ka/ka/status_node.pl IPADD on the golden node. ------| Ka |---- Install starting... 10.0.1.111> Current session is -s kainstall1 10.0.1.111> Receiving partitions information...OK 10.0.1.111> Cleaning hard drive... 10.0.1.111> ==> /tmp/kacmd <== 10.0.1.111> Starting log server.. 10.0.1.111> 10.0.1.111> ==> /tmp/ka_log-10.0.1.111-20100507-10h32 <== 10.0.1.111> OK 10.0.1.111> Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel 10.0.1.111> Building a new DOS disklabel with disk identifier 0x59be1427. 10.0.1.111> Changes will remain in memory only, until you decide to write them. 10.0.1.111> After that, of course, the previous content won't be recoverable. 10.0.1.111> 10.0.1.111> 10.0.1.111> The number of cylinders for this disk is set to 1116. 10.0.1.111> There is nothing wrong with that, but this is larger than 1024, 10.0.1.111> and could in certain setups cause problems with: 10.0.1.111> 1) software that runs at boot time (e.g., old versions of LILO) 10.0.1.111> 2) booting and partitioning software from other OSs 10.0.1.111> (e.g., DOS FDISK, OS/2 FDISK) 10.0.1.111> Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) 10.0.1.111> 10.0.1.111> Command (m for help): The partition table has been altered! 10.0.1.111> 10.0.1.111> Calling ioctl() to re-read partition table. 10.0.1.111> Syncing disks. 10.0.1.111> Writing partition table for sda using fdisk...OK 10.0.1.111> Formatting /dev/sda2 as ext3...OK 10.0.1.111> Formatting /dev/sda5 as ext4...OK 10.0.1.111> Formatting /dev/sda1 as swap...OK 10.0.1.111> - Mounting /dev/sda2 as /mnt/disk/ ......OK 10.0.1.111> - Mounting /dev/sda5 as /mnt/disk/home ......OK 10.0.1.111> ++++++++++++++++++++++++++ 10.0.1.111> none on /sys type sysfs (rw,relatime) 10.0.1.111> none on /proc/bus/usb type usbfs (rw,relatime) 10.0.1.111> /dev/ram3 on /tmp/stage2 type ext2 (rw,relatime,errors=continue) 10.0.1.111> /dev/sda2 on /mnt/disk type ext3 (rw,relatime,errors=continue,data=ordered) 10.0.1.111> /dev/sda5 on /mnt/disk/home type ext4 (rw,relatime,barrier=1,data=ordered) 10.0.1.111> ++++++++++++++++++++++++++ 10.0.1.111> Linux copy is about to start 10.0.1.111> Server IP is 10.0.1.42 10.0.1.111> Buffers names :pipe Total data received = 21 Megs (10.830 Mbytes/sec); BUF :0M 10.0.1.111> ==> /tmp/kacmd <== 10.0.1.111> Starting log server.. 10.0.1.111> 10.0.1.111> ==> /tmp/ka_log-localhost-20100507-11h17 <== Total data received = 788 Megs (10.796 Mbytes/sec); BUF :0M End of data flow 10.0.1.111> Flushing buffers 10.0.1.111> Total data received = 792 Megs, in 574479 packets 10.0.1.111> Elapsed time = 73.413 seconds, throughput = 10.801 Mbytes/second 10.0.1.111> Syncing disks...OK 10.0.1.111> Linux copy done. 10.0.1.111> Creating excluded directories 10.0.1.111> - bootloader is grub (user choice) 10.0.1.111> `/tmp/partfiles/pfstab' -> `/mnt/disk/etc/fstab' 10.0.1.111> - Removing duplicated dhcp cache 10.0.1.111> - Writing modprobe.conf 10.0.1.111> ******************** 10.0.1.111> install scsi_hostadapter /sbin/modprobe aic7xxx; /bin/true 10.0.1.111> install scsi_hostadapter /sbin/modprobe pata_serverworks; /bin/true 10.0.1.111> alias eth0 tg3 10.0.1.111> alias eth1 tg3 10.0.1.111> ******************** 10.0.1.111> - Remove persistent udev rules 10.0.1.111> removed `/mnt/disk/etc/udev/rules.d/70-persistent-net.rules' 10.0.1.111> - Fix /dev in /mnt/disk 10.0.1.111> `/ka2/udev_creation.sh' -> `/mnt/disk/sbin/udev_creation.sh' 10.0.1.111> Starting udev: [ OK ] 10.0.1.111> umount: /mnt/disk/dev: device is busy. 10.0.1.111> (In some cases useful info about processes that use 10.0.1.111> the device is found by lsof(8) or fuser(1)) 10.0.1.111> - Running mkinitrd 10.0.1.111> - Looking for default grub menu 10.0.1.111> - erase old initrd.img link 10.0.1.111> removed `/mnt/disk/boot/initrd.img' 10.0.1.111> initrd will be : /boot/initrd-2.6.33.3-desktop-1mnb.img 10.0.1.111> running: chroot /mnt/disk /sbin/mkinitrd -v -f /boot/initrd-2.6.33.3-desktop-1mnb.img 2.6.33.3-desktop-1mnb 10.0.1.111> Creating initramfs 10.0.1.111> Looking for driver for /dev/sda2 in /sys/block/sda/sda2 10.0.1.111> Looking for deps of module scsi:t-0x00: crc-t10dif scsi_mod sd_mod 10.0.1.111> Looking for deps of module pci:v00009005d000000CFsv00001028sd00000121bc01sc00i00: scsi_mod scsi_transport_spi aic7xxx 10.0.1.111> Looking for deps of module pci:v00008086d00000309sv00000000sd00000000bc06sc04i00: pci_hotplug shpchp 10.0.1.111> Looking for driver for /dev/sda1 in /sys/block/sda/sda1 10.0.1.111> Using modules: usbhid ehci-hcd ohci-hcd uhci-hcd ext3 crc-t10dif scsi_mod sd_mod scsi_transport_spi aic7xxx pci_hotplug shpchp pata_serverworks 10.0.1.111> Building initrd in /tmp/initrd.uuIIkZ 10.0.1.111> /sbin/nash -> /tmp/initrd.uuIIkZ/bin/nash 10.0.1.111> /usr/lib/libnash.so.6.0.93 -> /tmp/initrd.uuIIkZ/usr/lib/libnash.so.6.0.93 10.0.1.111> /lib/libdevmapper.so.1.02 -> /tmp/initrd.uuIIkZ/lib/libdevmapper.so.1.02 10.0.1.111> /lib/libreadline.so.6 -> /tmp/initrd.uuIIkZ/lib/libreadline.so.6 10.0.1.111> /lib/libreadline.so.6.1 -> /tmp/initrd.uuIIkZ/lib/libreadline.so.6.1 10.0.1.111> /lib/libncurses.so.5 -> /tmp/initrd.uuIIkZ/lib/libncurses.so.5 10.0.1.111> /lib/libncurses.so.5.7 -> /tmp/initrd.uuIIkZ/lib/libncurses.so.5.7 10.0.1.111> /lib/libc.so.6 -> /tmp/initrd.uuIIkZ/lib/libc.so.6 10.0.1.111> /lib/libc-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/libc-2.11.1.so 10.0.1.111> /lib/ld-linux.so.2 -> /tmp/initrd.uuIIkZ/lib/ld-linux.so.2 10.0.1.111> /lib/ld-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/ld-2.11.1.so 10.0.1.111> /lib/libdl.so.2 -> /tmp/initrd.uuIIkZ/lib/libdl.so.2 10.0.1.111> /lib/libdl-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/libdl-2.11.1.so 10.0.1.111> /lib/libudev.so.0 -> /tmp/initrd.uuIIkZ/lib/libudev.so.0 10.0.1.111> /lib/libudev.so.0.7.0 -> /tmp/initrd.uuIIkZ/lib/libudev.so.0.7.0 10.0.1.111> /usr/lib/libparted.so.0 -> /tmp/initrd.uuIIkZ/usr/lib/libparted.so.0 10.0.1.111> /usr/lib/libparted.so.0.0.1 -> /tmp/initrd.uuIIkZ/usr/lib/libparted.so.0.0.1 10.0.1.111> /lib/libuuid.so.1 -> /tmp/initrd.uuIIkZ/lib/libuuid.so.1 10.0.1.111> /lib/libuuid.so.1.3.0 -> /tmp/initrd.uuIIkZ/lib/libuuid.so.1.3.0 10.0.1.111> /lib/libblkid.so.1 -> /tmp/initrd.uuIIkZ/lib/libblkid.so.1 10.0.1.111> /lib/libblkid.so.1.1.0 -> /tmp/initrd.uuIIkZ/lib/libblkid.so.1.1.0 10.0.1.111> /lib/libpopt.so.0 -> /tmp/initrd.uuIIkZ/lib/libpopt.so.0 10.0.1.111> /lib/libpopt.so.0.0.0 -> /tmp/initrd.uuIIkZ/lib/libpopt.so.0.0.0 10.0.1.111> /lib/libresolv.so.2 -> /tmp/initrd.uuIIkZ/lib/libresolv.so.2 10.0.1.111> /lib/libresolv-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/libresolv-2.11.1.so 10.0.1.111> /usr/lib/libelf.so.1 -> /tmp/initrd.uuIIkZ/usr/lib/libelf.so.1 10.0.1.111> /usr/lib/libelf-0.146.so -> /tmp/initrd.uuIIkZ/usr/lib/libelf-0.146.so 10.0.1.111> /lib/libm.so.6 -> /tmp/initrd.uuIIkZ/lib/libm.so.6 10.0.1.111> /lib/libm-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/libm-2.11.1.so 10.0.1.111> /lib/libgcc_s.so.1 -> /tmp/initrd.uuIIkZ/lib/libgcc_s.so.1 10.0.1.111> /lib/libgcc_s-4.4.3.so.1 -> /tmp/initrd.uuIIkZ/lib/libgcc_s-4.4.3.so.1 10.0.1.111> /usr/lib/libbdevid.so.6.0.93 -> /tmp/initrd.uuIIkZ/usr/lib/libbdevid.so.6.0.93 10.0.1.111> /sbin/modprobe -> /tmp/initrd.uuIIkZ/bin/modprobe 10.0.1.111> /lib/libmodprobe.so.0 -> /tmp/initrd.uuIIkZ/lib/libmodprobe.so.0 10.0.1.111> /lib/libmodprobe.so.0.0.0 -> /tmp/initrd.uuIIkZ/lib/libmodprobe.so.0.0.0 10.0.1.111> /lib/libz.so.1 -> /tmp/initrd.uuIIkZ/lib/libz.so.1 10.0.1.111> /lib/libz.so.1.2.3 -> /tmp/initrd.uuIIkZ/lib/libz.so.1.2.3 10.0.1.111> /sbin/rmmod -> /tmp/initrd.uuIIkZ/bin/rmmod 10.0.1.111> /bin/ln -> /tmp/initrd.uuIIkZ/bin/ln 10.0.1.111> resolving for MODULES 10.0.1.111> and that has items of usbhid ehci-hcd ohci-hcd uhci-hcd ext3 crc-t10dif scsi_mod sd_mod scsi_transport_spi aic7xxx pci_hotplug shpchp pata_serverworks 10.0.1.111> Looking for deps of module usbhid: usbcore hid 10.0.1.111> Looking for deps of module ehci-hcd: usbcore 10.0.1.111> Looking for deps of module ohci-hcd: usbcore 10.0.1.111> Looking for deps of module uhci-hcd: usbcore 10.0.1.111> Looking for deps of module ext3: jbd 10.0.1.111> Looking for deps of module crc-t10dif 10.0.1.111> Looking for deps of module scsi_mod 10.0.1.111> Looking for deps of module sd_mod: crc-t10dif scsi_mod 10.0.1.111> Looking for deps of module scsi_transport_spi: scsi_mod 10.0.1.111> Looking for deps of module aic7xxx: scsi_mod scsi_transport_spi 10.0.1.111> Looking for deps of module pci_hotplug 10.0.1.111> Looking for deps of module shpchp: pci_hotplug 10.0.1.111> Looking for deps of module pata_serverworks: scsi_mod libata 10.0.1.111> Looking for deps of module aic7xxx: scsi_mod scsi_transport_spi 10.0.1.111> Looking for deps of module crc-t10dif 10.0.1.111> Looking for deps of module ehci-hcd: usbcore 10.0.1.111> Looking for deps of module ext3: jbd 10.0.1.111> Looking for deps of module hid 10.0.1.111> Looking for deps of module jbd 10.0.1.111> Looking for deps of module libata: scsi_mod 10.0.1.111> Looking for deps of module ohci-hcd: usbcore 10.0.1.111> Looking for deps of module pata_serverworks: scsi_mod libata 10.0.1.111> Looking for deps of module pci_hotplug 10.0.1.111> Looking for deps of module scsi_mod 10.0.1.111> Looking for deps of module scsi_transport_spi: scsi_mod 10.0.1.111> Looking for deps of module sd_mod: crc-t10dif scsi_mod 10.0.1.111> Looking for deps of module shpchp: pci_hotplug 10.0.1.111> Looking for deps of module uhci-hcd: usbcore 10.0.1.111> Looking for deps of module usbcore 10.0.1.111> Looking for deps of module usbhid: usbcore hid 10.0.1.111> resolving for availmodules 10.0.1.111> and that has items of 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/scsi/aic7xxx/aic7xxx.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/aic7xxx.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/lib/crc-t10dif.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/crc-t10dif.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/usb/host/ehci-hcd.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/ehci-hcd.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/fs/ext3/ext3.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/ext3.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/hid/hid.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/hid.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/fs/jbd/jbd.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/jbd.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/ata/libata.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/libata.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/usb/host/ohci-hcd.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/ohci-hcd.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/ata/pata_serverworks.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/pata_serverworks.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/pci/hotplug/pci_hotplug.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/pci_hotplug.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/scsi/scsi_mod.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/scsi_mod.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/scsi/scsi_transport_spi.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/scsi_transport_spi.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/scsi/sd_mod.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/sd_mod.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/pci/hotplug/shpchp.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/shpchp.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/usb/host/uhci-hcd.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/uhci-hcd.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/usb/core/usbcore.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/usbcore.ko.gz 10.0.1.111> /lib/modules/2.6.33.3-desktop-1mnb/kernel/drivers/hid/usbhid/usbhid.ko.gz -> /tmp/initrd.uuIIkZ/lib/modules/2.6.33.3-desktop-1mnb/usbhid.ko.gz 10.0.1.111> /etc/sysconfig/keyboard -> /tmp/initrd.uuIIkZ/etc/sysconfig/keyboard 10.0.1.111> /bin/loadkeys -> /tmp/initrd.uuIIkZ/bin/loadkeys 10.0.1.111> /etc/sysconfig/console/default.kmap -> /tmp/initrd.uuIIkZ/etc/sysconfig/console/default.kmap 10.0.1.111> /etc/sysconfig/i18n -> /tmp/initrd.uuIIkZ/etc/sysconfig/i18n 10.0.1.111> /bin/setfont -> /tmp/initrd.uuIIkZ/bin/setfont 10.0.1.111> /usr/lib/kbd/consolefonts/lat0-16.psfu.gz -> /tmp/initrd.uuIIkZ/usr/lib/kbd/consolefonts/lat0-16.psfu.gz 10.0.1.111> /lib/udev/console_init -> /tmp/initrd.uuIIkZ/lib/udev/console_init 10.0.1.111> probing for drm modules for pci device /sys/bus/pci/devices/0000:00:0e.0 10.0.1.111> Adding graphics device /sys/bus/pci/devices/0000:00:0e.0 10.0.1.111> Looking for deps of module pci:v00001002d00004752sv00001028sd00000121bc03sc00i00 10.0.1.111> resolving for GRAPHICSMODS 10.0.1.111> and that has items of 10.0.1.111> Adding module usbhid 10.0.1.111> Adding module ehci-hcd 10.0.1.111> Adding module ohci-hcd 10.0.1.111> Adding module uhci-hcd 10.0.1.111> Adding module ext3 10.0.1.111> Adding module crc-t10dif 10.0.1.111> Adding module scsi_mod 10.0.1.111> Adding module sd_mod 10.0.1.111> Adding module scsi_transport_spi 10.0.1.111> Adding module aic7xxx 10.0.1.111> Adding module pci_hotplug 10.0.1.111> Adding module shpchp 10.0.1.111> Adding module pata_serverworks 10.0.1.111> /usr/sbin/resume -> /tmp/initrd.uuIIkZ/bin/resume 10.0.1.111> /usr/lib/suspend/resume -> /tmp/initrd.uuIIkZ/usr/lib/suspend/resume 10.0.1.111> /usr/lib/liblzo2.so.2 -> /tmp/initrd.uuIIkZ/usr/lib/liblzo2.so.2 10.0.1.111> /usr/lib/liblzo2.so.2.0.0 -> /tmp/initrd.uuIIkZ/usr/lib/liblzo2.so.2.0.0 10.0.1.111> /lib/libpthread.so.0 -> /tmp/initrd.uuIIkZ/lib/libpthread.so.0 10.0.1.111> /lib/libpthread-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/libpthread-2.11.1.so 10.0.1.111> /lib/libply.so.2 -> /tmp/initrd.uuIIkZ/lib/libply.so.2 10.0.1.111> /lib/libply.so.2.0.0 -> /tmp/initrd.uuIIkZ/lib/libply.so.2.0.0 10.0.1.111> /lib/librt.so.1 -> /tmp/initrd.uuIIkZ/lib/librt.so.1 10.0.1.111> /lib/librt-2.11.1.so -> /tmp/initrd.uuIIkZ/lib/librt-2.11.1.so 10.0.1.111> /lib/libply-splash-core.so.2 -> /tmp/initrd.uuIIkZ/lib/libply-splash-core.so.2 10.0.1.111> /lib/libply-splash-core.so.2.0.0 -> /tmp/initrd.uuIIkZ/lib/libply-splash-core.so.2.0.0 10.0.1.111> /etc/suspend.conf -> /tmp/initrd.uuIIkZ/etc/suspend.conf 10.0.1.111> This initrd uses dynamic shared objects. 10.0.1.111> Adding dynamic linker configuration files. 10.0.1.111> /etc/ld.so.conf -> /tmp/initrd.uuIIkZ/etc/ld.so.conf 10.0.1.111> Running ldconfig 10.0.1.111> Installation finished. No error reported. 10.0.1.111> This is the contents of the device map /boot/grub/device.map. 10.0.1.111> Check if this is correct or not. If any of the lines is incorrect, 10.0.1.111> fix it and re-run the script `grub-install'. 10.0.1.111> 10.0.1.111> (hd0) /dev/sda 10.0.1.111> Umounting /dev/sda5...OK 10.0.1.111> Umounting /dev/sda2...OK 10.0.1.111> ftp: connect: Connection refused 10.0.1.111> Local directory now /tmp 10.0.1.111> Not connected. ]]> Now client nodes reboots, so we have to switch PXE to a local boot. Nodes hsould be up, we can to see their hardware.