diff options
Diffstat (limited to 'perl-install/standalone/drakvpn')
| -rw-r--r-- | perl-install/standalone/drakvpn | 20 |
1 files changed, 12 insertions, 8 deletions
diff --git a/perl-install/standalone/drakvpn b/perl-install/standalone/drakvpn index bbac1a717..c87c3b03f 100644 --- a/perl-install/standalone/drakvpn +++ b/perl-install/standalone/drakvpn @@ -1029,7 +1029,7 @@ So, here, the lifetime units are 'min', 'min', 'sec', 'sec', 'sec' and 'hour'. { label => N("Authentication algorithm"), val => \$data->{5}[1], list => [ qw(des 3des des_iv64 des_iv32 hmac_md5 hmac_sha1 non_auth) ] }, { label => N("Compression algorithm"), val => \$data->{6}[1], - list => [ 'deflate' ], allow_empty_list => 1 } + list => [ N_("deflate") ], format => \&translate, allow_empty_list => 1 } ]) } @@ -1054,7 +1054,7 @@ specified by separating them with a comma. All of the modes are acceptable. The first exchange mode is what racoon uses when it is the initiator.\n") }, { label => N("Generate policy"), val => \$main_remote_section->{3}[1], - list => [ 'off', 'on' ], + list => [ N_("off"), N_("on") ], format => \&translate, help => N("This directive is for the responder. Therefore you should set passive on in order that racoon(8) only becomes a responder. If the responder does not have any @@ -1070,7 +1070,7 @@ installed due to some policy mismatches between the ini- tiator and the responder. This directive is ignored in the initiator case. The default value is off.") }, { label => N("Passive"), val => \$main_remote_section->{4}[1], - list => [ 'off', 'on' ], + list => [ N_("off"), N_("on") ], format => \&translate, help => N("If you do not want to initiate the negotiation, set this to on. The default value is off. It is useful for a server.") }, @@ -1083,7 +1083,7 @@ server.") }, { label => N("Peers certfile"), val => \$main_remote_section->{6}[1], type => 'entry', help => N("Name of the peers certificate") }, { label => N("Verify cert"), val => \$main_remote_section->{7}[1], - list => [ 'off', 'on' ], + list => [ N_("off"), N_("on") ], format => \&translate, help => N("If you do not want to verify the peer's certificate for some reason, set this to off. The default is on.") }, { label => N("My identifier"), val => \$main_remote_section->{8}[1], type => 'entry', @@ -1129,14 +1129,18 @@ sub ask_info3 { [ { label => N("Command"), val => \$section->{command}, list => [ 'spdadd' ], allow_empty_list => 1 }, { label => N("Source IP range"), val => \$section->{src_range}, type => 'entry' }, { label => N("Destination IP range"), val => \$section->{dst_range}, type => 'entry' }, - { label => N("Upper-layer protocol"), val => \$section->{upperspec}, list => [ 'any' ], allow_empty_list => 1 }, + { label => N("Upper-layer protocol"), val => \$section->{upperspec}, list => [ N_("any") ], + format => \&translate, allow_empty_list => 1 }, { label => N("Flag"), val => \$section->{flag}, list => [ '-P' ], allow_empty_list => 1 }, { label => N("Direction"), val => \$section->{direction}, list => [ 'in', 'out' ] }, - { label => N("IPsec policy"), val => \$section->{ipsec}, list => [ 'ipsec', 'discard', 'none' ] }, + { label => N("IPsec policy"), val => \$section->{ipsec}, list => [ N_("ipsec"), N_("discard"), N_("none") ], + format => \&translate }, { label => N("Protocol"), val => \$section->{protocol}, list => [ 'esp', 'ah', 'ipcomp' ] }, - { label => N("Mode"), val => \$section->{mode}, list => [ 'tunnel', 'transport', 'any' ] }, + { label => N("Mode"), val => \$section->{mode}, list => [ N_("tunnel"), N_("transport"), N_("any") ], + format => \&translate }, { label => N("Source/destination"), val => \$section->{src_dest}, type => 'entry' }, - { label => N("Level"), val => \$section->{level}, list => [ 'require', 'default', 'use', 'unique' ] }, + { label => N("Level"), val => \$section->{level}, list => [ N_("require"), N_("default"), N_("use"), N_("unique") ], + format => \&translate }, ]); } |