DrakX, Mageias installerare

Oavsett om du är ny på GNU-Linux eller en erfaren användare så är Mageias installerare utformad för att göra din installation eller uppgradering så enkel som möjligt.

Installationsstegen

  • The install process is divided into a number of steps - the status of which is indicated in a panel to the left of the screen.

  • Each step has one or more screens, which may also have Advanced sections with extra, less commonly required options.

  • Most screens have Help buttons for further details about the particular step.

[Observera]

If at some point during the install you decide to abort the installation, it is possible to reboot, but please think twice before you do this. Once a partition has been formatted or updates have started to be installed, your computer is no longer in the same state and rebooting it could very well leave you with an unusable system.

If, in spite of this, you are very sure rebooting is what you want, go to a text terminal by pressing the keys Ctrl+Alt+F2 together. After that, press Ctrl+Alt+Delete together to reboot.

Välkomstskärm för installationen

The particular screen that you will first see when booting from the Installation media will depend on whether your computer motherboard is of the Legacy (BIOS) or UEFI type.

The welcome menu screen has various options, however the default option will start the installer, and is normally all that you will need.

Legacy (BIOS) Systems

Meny

  • Installera Mageia

    Install Mageia to a hard disk. This is the default option, and will automatically start after a short while unless another option is selected.

  • Rescue System

    This option allows you to either re-install the bootloader for an existing Mageia installation or you can use it to restore a Windows bootloader.

  • Minnestest

    Test the installed RAM by performing multiple read and write operations. Reboot to end the test.

  • F2: Språk

    Tryck F2 för alternativa språk.

UEFI-system

From this screen, you can access options by pressing e to enter the edit mode. To come back to this screen, press Esc to quit without saving or press F10 to save and quit.

Meny

  • Installera: Påbörja installationsprocessen

  • Rescue: This option allows you to either re-install the bootloader for an existing Mageia installation or you can use it to restore a Windows bootloader.

  • F2: Språk: Tryck F2 för alternativa språk.

If you booted from a USB stick, you will see the above options duplicated, and in this case, you should use the set that will be suffixed with "USB".

Installationsproblem och möjliga lösningar

Inget grafiskt gränssnitt

  • After the initial screen you did not progress to the Language Selection screen. This can happen with some graphic cards and older systems. Try using low resolution by typing vgalo at the prompt.

  • If the hardware is very old, a graphical installation may not be possible. In this case it is worth trying a text-mode installation. To use this press Esc at the Welcome screen and confirm with ENTER. You will be presented with a black screen with a boot: prompt. Type text and press ENTER to continue with the installation in text mode.

Installationen hänger sig

If the system appeared to freeze during the installation, this may be a problem with hardware detection. In this case the automatic hardware detection may be bypassed and dealt with later. To try this, type noauto at the prompt. This option may also be combined with other parameters as necessary.

RAM-problem

This will rarely be needed, but in some cases the hardware may report the available RAM incorrectly. To specify this manually, you can use the mem=xxxM parameter, where xxx is the correct amount of RAM. e.g. mem=256M would specify 256MB of RAM.

Dynamiska partitioner

If you converted your hard disk from Basic format to Dynamic format in Microsoft Windows, then it is not possible to install Mageia on this disc. To revert to a Basic disk, see the Microsoft documentation: http://msdn.microsoft.com/en-us/library/cc776315.aspx.