From 4b3b214c2ffdd2f1d40d245472aa5aba29d26047 Mon Sep 17 00:00:00 2001 From: Papoteur Date: Tue, 2 Jul 2019 16:04:08 +0200 Subject: Adding or refreshing mcc in cs --- mcc/7/cs/content/mcc-hardware.html | 302 +++++++++++++++++++++++++++++++++++++ 1 file changed, 302 insertions(+) create mode 100644 mcc/7/cs/content/mcc-hardware.html (limited to 'mcc/7/cs/content/mcc-hardware.html') diff --git a/mcc/7/cs/content/mcc-hardware.html b/mcc/7/cs/content/mcc-hardware.html new file mode 100644 index 00000000..aeb809b8 --- /dev/null +++ b/mcc/7/cs/content/mcc-hardware.html @@ -0,0 +1,302 @@ + + + + + Hardware

Hardware

Na této obrazovce si můžete vybrat mezi několika nástroji pro konfiguraci +hardware. Klikněte na odkaz níže a dozvíte se více.

  1. Spravovat hardware

    1. „Nastavení hardware“ = Procházet a nastavit +hardware

    2. „Nastavit zvuk“

  2. Nastavit grafiku

    1. „3D efekty grafického prostředí“ = Konfigurace efektů 3D pracovní +plochy

    2. „Nastavit grafický server“

  3. Nastavit tisk a skenování

    1. „Instalace a konfigurace tiskárny“ = Nastavení tiskáren, +fronty tiskových úloh, ...

    2. „Nastavit skener“

Nastavení hardware

harddrake2

This tool[11] gives a general view of the +hardware of your computer. When the tool is launched, it executes a job to +look for every element of the hardware. For that, it uses the command +ldetect which refers to a list of hardware in +ldetect-lst package.

The window

The window is divided in two columns.

The left column contains a list of the detected hardware. The devices are +grouped by categories. Click on the > to expand the content of a +category. Each device can be selected in this column.

The right column displays information about the selected device. The +Help -> Fields description gives some information +about the content of the fields.

According to which type of device is selected, either one or two buttons are +available at the bottom of the right column:

  • Set current driver options: this can be used to +parameterize the module which is used in relation to the device. This must +used by experts only.

  • Run config tool: access to the tool which can +configure the device. The tool can often be accessed directly from the MCC.

The menu

Volby

The options menu gives the opportunity to check boxes to +enable automatic detection:

  • modem

  • Jednotka JAZ

  • Paralelní jednotka ZIP

By default these detections are not enabled, because they are slow. Check +the appropriate box(es) if you have this hardware connected. Detection will +be operational the next time this tool is started.

Nastavit zvuk

draksound

This tool[12] is present in the Mageia +Control Center under the tab Hardware.

Draksound deals with the sound configuration, PulseAudio options and +troubleshooting. It will help you if you experience sound problems or if you +change the sound card.

PulseAudio is a sound server. It receives all the sound +inputs, mixes them according to the user preferences and sends the resulting +sound to the output. See Menu ->Sound and video -> PulseAudio +volume control to set these preferences.

PulseAudio is the default sound server and it is recommended to leave it +enabled.

Glitch-Free improves PulseAudio with some programs. It +is also recommended to leave it enabled.

The Troubleshooting button gives assistance with +fixing any problems you may have. You will find it helpful to try this +before asking the community for help.

The Advanced button displays a new window with an +obvious button.

3D efekty grafického prostředí

drak3d

Úvod

This tool[13] lets you manage the 3D +desktop effects on your operating system. 3D effects are turned off by +default.

Začínáme

To use this tool, you need to have the glxinfo package installed. If the +package is not installed, you will be prompted to do so before drak3d can +start.

After starting drak3d, you will be presented with a menu window. Here you +can choose either No 3D Desktop Effects or +Compiz Fusion. Compiz Fusion is part of a +composite/window manager, which includes hardware-accelerated special +effects for your desktop. Choose Compiz Fusion to turn +it on.

If this is your first time using this program after a clean installation of +Mageia, you will get a warning message telling you which packages need to be +installed in order to use Compiz Fusion. Click on the +Ok button to continue.

Once the appropriate packages are installed, you will notice that Compiz +Fusion is selected in the drak3d menu, but you must log out and log back in +for the changes to take effect.

After logging back in, Compiz Fusion will be activated. To configure Compiz +Fusion, see the page for the ccsm (CompizConfig Settings Manager) tool.

Řešení problémů

Can't See Desktop after Logging in

If after turning on Compiz Fusion you attempt to log back into your desktop +but can't see anything, restart your computer to get back to the log in +screen. Once there, click on the Desktop icon and select drak3d.

When you log in, if your account is listed as an administrator, you will be +prompted for your password again. Otherwise, use the administrator login +with his/her account. Then you can undo any changes that may have caused the +log in problem.

Nastavit grafický server

XFdrake

This tool is present in the Mageia Control Center under the tab Hardware. Select Set up the +graphical server. [14]

The buttons allow you to change the graphical configuration.

Grafická karta:

The graphic card currently detected is displayed and the matching server +configured. Click on this button to change to another server, for example +one with a proprietary driver.

The available servers are sorted under Vendor by +manufacturer in alphabetical order and then by model also in alphabetical +order. The free drivers are sorted by alphabetical order under +Xorg.

Poznámka

In case of problems, Xorg - Vesa will work with most +graphic cards and give you time to find and install the right driver while +in your Desktop Environment.

If even Vesa doesn't work, choose Xorg - +fbdev, which is used while installing +Mageia, but doesn't allow you to change resolution or refresh rates.

If you made your choice for a free driver, you may be asked if you want to +use a proprietary driver instead with more features (3D effects for +example).

Monitor:

In the same way as above, the monitor currently detected is displayed and +you can click on the button to change to another one. If the desired monitor +isn't in the Vendor list, choose in the +Generic list a monitor with the same features.

Resolution:

This button allows the choice of the resolution (number of pixels) and the +colour depth (number of colours). It displays this screen:

When you change the color depth, a +multi-colored bar will appear next to the second button and show a preview +of what the selected color depth looks like.

The first button shows the currently resolution, click to change for another +one. The list gives all the possible choices according to the graphic card +and the monitor, it is possible to click on Other to +set other resolutions, but bear in mind that you can damage your monitor or +select an uncomfortable setting.

The second button shows the currently colour depth, click to change this for +another one.

Poznámka

Depending on the chosen resolution, it may be necessary to logout and +restart the graphical environment for the settings to take effect.

Test:

Once the configuration done, it is recommended to do a test before clicking +on OK because it is easier to modify the settings now than later if the +graphical environment doesn't work.

Poznámka

In case of a non working graphical environment, type Alt+Ctrl+F2 to open a +text environment, connect as root and type XFdrake (with the caps) to to use +XFdrake's text version.

If the test fails, just wait until the end, if it works but you don't want +to change after all, click on No, if everything is +right, click on OK.

Volby:

  1. Global options: If Disable +Ctrl-Alt-Backspace is checked, it will no longer be possible to +restart X server using Ctrl+Alt+Backspace keys.

  2. Graphic card options: Allows you to enable or disable +three specific features depending on the graphic card.

  3. Graphical interface at startup: Most of the time, +Automatically start the graphical interface (Xorg) upon +booting is checked to make the boot switch to graphical mode, it +may be unchecked for a server.

After a click on the Quit button, the system will ask +you to confirm. There is still time to cancel everything and keep the +previous configuration, or to accept. In this case, you have to disconnect +and reconnect to activate the new configuration.

Set up the Keyboard Layout

keyboarddrake

Úvod

The keyboarddrake tool[15] helps you +configure the basic layout for the keyboard that you wish to use on +Mageia. It affects the keyboard layout for all users on the system. It can +be found in the Hardware section of the Mageia Control Center (MCC) labelled +"Configure mouse and keyboard".

Rozložení klávesnice

Here you can select which keyboard layout you wish to use. The names (listed +in alphabetical order) describe the language, country, and/or ethnicity each +layout should be used for.

Typ klávesnice

This menu lets you select the type of keyboard you are using. If you are +unsure of which to choose, it is best to leave it as the default type.

Nastavit polohovací zařízení (myš, touchpad)

mousedrake

This tool[16] is present in the Mageia +Control Center under the tab Hardware.

As you must have a mouse to install Mageia, that one is already installed by +Drakinstall. This tool allows installation of another mouse.

The mice are sorted by connection type and then by model. Select your mouse +and click on OK. Most of the time "Universal / Any +PS/2 & USB mice" is suitable for a recent mouse. The new mouse is +immediately taken into account.

Instalace a konfigurace tiskárny

system-config-printer

Úvod

Printing is managed on Mageia by a server named CUPS. It has its own configuration +interface which is accessible via an Internet browser, but Mageia +offers its own tool for installing printers called system-config-printer +which is shared with other distributions such as Fedora, Mandriva, Ubuntu +and openSUSE.

You should enable the non-free repository before proceeding with the +installation, because some drivers may only be available in this way.

Printer installation is carried out in the Hardware +section of the Mageia Control Centre. Select the Configure +printing and scanning tool[17].

MCC bude žádat o instalaci dvou balíčků:

task-printing-server

task-printing-hp

Pro pokračování je třeba akceptovat tuto instalaci. Závislosti mohou +potřebovat až 230MB.

Chcete-li přidat tiskárnu, klepněte na tlačítko "Přidat tiskárnu". Systém se +bude snažit odhalit všechny tiskárny a porty které jsou k dispozici. Snímek +zobrazuje tiskárny připojené k paralelnímu portu. Pokud je zjištěna tiskárna +na USB portu, bude zobrazena na prvním řádku. Okno se také pokusí +nakonfigurovat síťové tiskárny.

Automatically detected printer

This usually refers to USB printers. The utility automatically finds the +name of the printer and displays it. Select the printer and then click +"Next". If there is a known driver associated for the printer, it will be +automatically installed. If there is more than one driver or no known +drivers, a window will ask you to select or furnish one, as explained in the +next paragraph. Continue with „Complete the installation process“

No automatically detected printer

When you select a port, the system loads a driver list and displays a window +to select a driver. The choice can be made through one of the following +options.

  • Výběr tiskárny z databáze

  • provide PPD file

  • search for a driver to download

By selecting from the database, the window suggests a printer manufacturer +first, and then a device and a driver associated with it. If more than one +driver is suggested, select one which is recommended, unless you have +encountered some problems with that one before, in this case select the one +which know to work.

Complete the installation process

After the driver selection, a window requests some information which will +allow the system to designate and discover the printer. The first line is +the name under which the device will appear in applications in the list of +available printers. The installer then suggests printing a test page. After +this step, the printer is added and appears in the list of available +printers.

Síťová tiskárna

Síťové tiskárny jsou tiskárny, které jsou připojeny přímo ke kabelové nebo +bezdrátové síti, jsou připojeny k printserveru nebo jsou připojeny k jiné +pracovní stanice, která slouží jako printserver.

Poznámka

Often, it is better to configure the DHCP server to always associate a fixed +IP address with the printer's MAC-address. Of course that should be the same +as the IP address the printer of printserver is set to, if it has a fixed +one.

The printer's Mac-address is a serial number given to the printer or +printserver or computer it is attached to, that can be obtained from a +configuration page printed by the printer or which may be written on a label +on the printer or printserver. If your shared printer is attached to a +Mageia system, you can run ifconfig on it +as root to find the MAC-address. It is the sequence of numbers and letters +after "HWaddr".

You can add your network printer by choosing the protocol it uses to talk to +your computer over the network. If you don't know which protocol to choose, +you can try the Network Printer - Find +Network Printer option in the Devices menu +and give the IP address of the printer in the box on the right, where it +says "host".

If the tool recognises your printer or printserver, it will propose a +protocol and a queue, but you can choose a more appropriate one from the +list below it or give the correct queue name if it isn't in the list.

Look in the documentation that came with your printer or printserver to find +which protocol(s) it supports and for possible specific queue names.

Protokoly síťového tisku

One current technique is one developed by Hewlett-Packard and known as +JetDirect. It allows access to a printer directly connected to the network +via an Ethernet port. You must know the IP-address at which the printer is +known on the network. This technique is also used inside some ADSL-routers +which contain an USB port to connect the printer. In this case, the +IP-address is that of the router. Note that the tool "Hp Device manager" can +manage dynamically configured IP-adress, setting an URI like +hp:/net/<name-of-the-printer> . In this case, fixed +IP-adress is not required.

Choose the option AppSocket/HP JetDirect as the +protocol and set the address in Host:, do not change +the Port Number, unless you know that it needs to be +changed. After the selection of the protocol, the selection of the driver is +the same as above.

The other protocols are:

  • Internet Printing Protocol (ipp): a printer which can +be accessed on a TCP/IP network via the IPP protocol, for example a printer +connected to a station using CUPS. This protocol may also be used also by +some ADSL-routers.

  • Internet Printing Protocol (https): the same as ipp, +but using http transport and with TLS secured protocol. The port has to be +defined. By default, the port 631 is used.

  • Internet Printing Protocol (ipps): the same as ipp, but +with TLS secured protocol.

  • LPD/LPR host or Printer: a printer which can be +accessed on a TCP/IP network via the LPD protocol, for example a printer +connected to a station using LPD.

  • Windows printer via SAMBA: a printer connected to a +station running Windows or a SMB server and shared.

The URI can also be added directly. Here are some examples on how to form +the URI:

  • Appsocket

    socket://ip-address-or-hostname:port

  • Internet Printing Protocol (IPP)

    ipp://ip-address-or-hostname:port-number/resource

    http://ip-address-or-hostname:port-number/resource

  • Line Printer Daemon (LPD) Protocol

    lpd://username@ip-address-or-hostname/queue

Additional information can be found in the CUPS +documentation.

Device Properties

You can access the properties of the device. The menu allows access to +parameters for the CUPS server. By default a CUPS server is launched on your +system, but you can specify a different one with the +Server | Connect... menu, +another window which gives access to the tuning of other specific parameters +of the server, following Server | +Settings.

Troubleshoot

You can find some information on occurring errors during printing by +inspecting /var/log/cups/error_log

You can also access to a tool to diagnose problems using the +Help | Troubleshoot menu.

Specifics

It is possible that some drivers for specific printers are not available in +Mageia or are not functional. In this case, have a look at the openprinting site to +check if a driver for your device is available. If yes, check if the package +is already present in Mageia and in this case install it manually. Then, +redo the installation process to configure the printer. In all cases, report +the problem in bugzilla or on the forum if you are comfortable with this +tool and furnish the model and driver information and whether the printer +works or not after installation. Here are some sources to find other +up-to-date drivers or for more recent devices.

Brother printers

This +page give a list of drivers provided by Brother. Search the driver +for your device, download the rpm(s) and install.

You should install Brother drivers before running the configuration utility.

Hewlett-Packard printers and All in one +devices

These devices use the hplip tool. It is installed automatically after the +detection or the selection of the printer. You can find other information +here. The +tool "HP Device Manager" is available in the System +menu. Also view configuration +for the management of the printer.

A HP All in one device must be installed as a printer and the scanner +features will be added. Note that sometimes, the Xsane interface doesn't +allow to scan films or slides (the lighting slid can't operate). In this +case, it is possible to scan, using the standalone mode, and save the +picture on a memory card or USB stick inserted in the device. Afterwards, +open your favourite imaging software and load your picture from the memory +card which is appeared in the /media folder.

Samsung colour printer

For specific Samsung and Xerox colour printers, this site provides drivers for +the QPDL protocol.

Epson printers and scanners

Drivers for Epson printers are available from this +search page. For the scanner part, you must install the "iscan-data" +package first, then "iscan" (in this order). A iscan-plugin package can also +be available and is to install. Choose the rpm packages +according to your architecture.

It is possible that the iscan package will generate a warning about a +conflict with sane. Users have reported that this warning can be ignored.

Canon printers

For Canon printers, it may be advisable to install a tool named turboprint +available here .

Nastavit skener

scannerdrake

Instalace

This tool [18] allows you to configure a +single scanner device or a multifunction device which includes scanning. It +also allows you to share local devices connected to this computer with a +remote computer or to access remote scanners.

When you start this tool for the first time, you may get the following +message:

"SANE packages need to be installed to use scanners

Do you want to install the SANE packages?"

Choose Yes to continue. It will install +scanner-gui and task-scanning if they are not yet +installed.

If your scanner is identified correctly, so if in the above screen you see +the name of your scanner, the scanner is ready for use with, for instance, +XSane or Simple Scan.

In that case, you might now want to want to configure the Scanner +sharing option. You can read about it in the „Scannersharing“.

However, if your scanner hasn't been correctly identified, and checking its +cable(s) and power switch and then pressing Search for new +scanners doesn't help, you'll need to press Add a +scanner manually.

Choose the brand of your scanner in the list you see, then its type from the +list for that brand and click Ok

Poznámka

If you can't find your scanner in the list, then click +Cancel

Please check whether your scanner is supported on the SANE: +Supported Devices page and ask for help in the forums.

Obrázek 1. Choose port


You can leave this setting to Auto-detect available +ports unless your scanner's interface is a parallel port. In that +case, select /dev/parport0 if you have only one.

After clicking Ok, in most cases you will see a screen +similar to the one below.

If you don't get that screen, then please read the „Extra installation steps“.

Scannersharing

Here you can choose whether the scanners connected to this machine should be +accessible by remote machines and by which remote machines. You can also +decide here whether scanners on remote machines should be made available on +this machine.

Scanner sharing to hosts : name or IP address of hosts can be added or +deleted from the list of hosts allowed to access the local device(s), on +this computer.

Usage of remote scanners : name or IP address of hosts can added or deleted +from the list of hosts which give access to a remote scanner.

Scanner sharing to hosts: you can add host.

Scanner sharing to hosts: specify which host(s) to add, or allow all remote +machines.

"All remote machines" are allowed to access the local scanner.

If the package saned is not yet installed, the tool +offers to do it.

At the end, the tool will alter these files:

/etc/sane.d/saned.conf

/etc/sane.d/net.conf

/etc/sane.d/dll.conf to add or comment the directive +"net"

It will also configure saned and +xinetd to be started on boot.

Specifics

  • Hewlett-Packard

    Most HP scanners are managed from HP Device Manager +(hplip) which also manages printers. In this case, this tool does not allow +you to configure it and invites you to use HP Device +Manager.

  • Epson

    Drivers are available from this +page. When indicated, you must install the +iscan-data package first, then +iscan (in this order). It is possible that the +iscan package will generate a warning about a conflict +with sane. Users have reported that this warning can be +ignored.

Extra installation steps

It is possible that after selecting a port for your scanner in the 1 – „Choose port“ screen, you need to take one or more extra +steps to correctly configure your scanner.

  • In some cases, you're told the scanner needs its firmware to be uploaded +each time it is started. This tool allows you to load it into the device, +after you installed it on your system. In this screen you can install the +firmware from a CD or a Windows installation, or install the one you +downloaded from an Internet site of the vendor.

    + When your device's firmware needs to be loaded, it can take a long time at +each first usage, possibly more than one minute. So be patient.

  • Also, you may get a screen telling you to adjust the +/etc/sane.d/"name_of_your_SANE_backend".conf file.

  • Read those or other instructions you get carefully and if you don't know +what to do, feel free to ask for help in the forums.

Nastavit UPS pro sledování elektrického napájení

drakups

This page hasn't been written yet for lack of resources. If you think you +can write this help, please contact the Doc +team. Thanking you in advance.

Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu drakups.



[11] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu harddrake2.

[12] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu draksound.

[13] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu drak3d.

[14] You can start this tool from the command line, by typing +XFdrake as normal user or drakx11 +as root. Mind the capital letters.

[15] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu keyboarddrake.

[16] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu mousedrake.

[17] You can start this tool from the command line, by typing +system-config-printer. The root password will be asked +for.

[18] Tento nástroj můžete spustit, jako root, přes příkazovou řádku, pomocí +příkazu scannerdrake.


Uploaded on 02/07/2019
loading table of contents...
-- cgit v1.2.1