Sare GuneadraknetcenterThis toolKomando-lerrotik tresna hau abiaraz dezakezu, draknetventer root bezala idatziz. is found under the Network
& Internet tab in the Mageia Control Center labelled "Network Center"SarreraWhen this tool is launched, a window opens listing all the networks
configured on the computer, whatever their type (wired, wireless, satellite,
etc.). When clicking on one of them, three or four buttons appear, depending
on the network type, to allow you to look after the network, change its
settings or connect/disconnect. This tool isn't intended to create a
network, for this see Set up a new network interface (LAN, ISDN,
ADSL, ...) in the same MCC tab.In the screenshot below, given as example, we can see two networks, the
first one is wired and connected, recognizable by this icon (this one is not connected ) and the second section shows wireless
networks, not connected recognizable by this icon and this one if connected. For the other network types,
the colour code is always the same, green if connected and red if not
connected.In the wireless part of the screen, you can also see all the detected
networks, with the SSID, the Signal
strengh, if they are encrypted (in red) or not (in green), and
the Operating mode. Click on the chosen one and then
either on Monitor, Configure
or Connect. It is possible here to go from a network
to another one. If a private network is selected, the Network Settings
window (see below) will open and ask you for extra settings ( an encryption
key in particular).Click on Refresh to update the screen.Pantaila botoiaThis button allows you to watch the network activity, downloads (toward the
PC, in red) and uploads (toward the Internet, in green). The same screen is
available by right clicking on the Internet icon in the system tray
-> Monitor Network.There is a tab for each network (here eth0 is the wired network, lo the
local loopback and wlan0 the wireless network) and a tab connection which
gives details about connection status.At the bottom of the window is a title Traffic
accounting, we will look at that in the next section.Konfiguratu botoiaA - kable sare batentzatIt is possible to change all the settings given during network
creation. Most of the time, checking Automatic IP(BOOTP/DHCP) will do, but in case of problems, manual
configuration may give better results.For a residential network, the IP address always looks
like 192.168.0.x, Netmask is 255.255.255.0, and the
Gateway and DNS servers are
available from your providers website.Enable traffic accounting if checked this will count
the traffic on a hourly, daily or monthly basis. The results are visible in
the Network monitor detailed in the previous section. Once enabled, you may
have to reconnect to the network.Allow interface to be controlled by Network
Manager:This section hasn't been written yet for lack of resources. If you think you
can write this help, please contact the Doc
team. Thanking you in advance.Botoi Aurreratua:This section hasn't been written yet for lack of resources. If you think you
can write this help, please contact the Doc
team. Thanking you in advance.B - kable sare batentzatOnly the items not already seen above are explained.Eragilea modua:Select Managed if the connection is via an access
point, there is an ESSID detected. Select
Ad-hoc if it is a peer to peer network. Select
Master if your network card is used as the
access point, your network card needs to support this mode.Encryption mode and Encryption key:If it is a private network, you need to know these settings.WEP uses a password and is weaker than WPA which uses a
passphrase. WPA Pre-Shared Key is also called WPA
personal or WPA home. WPA Enterprise is not often used
in private networks.Allow access point roaming:Roaming is a technology which enables allows computer to change its access
point while remaining connected to the network.Botoi Aurreratua:This page hasn't been written yet for lack of resources. If you think you
can write this help, please contact the Doc
team. Thanking you in advance.Ezarpen aurreratuetako botoiaThis section hasn't been written yet for lack of resources. If you think you
can write this help, please contact the Doc
team. Thanking you in advance.