aboutsummaryrefslogtreecommitdiffstats
path: root/sysconfig.txt
diff options
context:
space:
mode:
Diffstat (limited to 'sysconfig.txt')
-rw-r--r--sysconfig.txt35
1 files changed, 5 insertions, 30 deletions
diff --git a/sysconfig.txt b/sysconfig.txt
index c4b3e1f3..7cae03d1 100644
--- a/sysconfig.txt
+++ b/sysconfig.txt
@@ -229,15 +229,12 @@ Generic options:
missing link beat is considered to be unplugged.
Default: 2
-<<<<<<< HEAD
MIN_LINK_DETECTION_DELAY=<delay in seconds>
Force minimum link detection delay on all interfaces.
Default: 0
CRDA_DOMAIN=<domain>
Default wireless regulatory domain (man 8 crda).
-=======
->>>>>>> initscripts-9.41-1
IPV6FORWARDING=yes|no
Enable or disable global forwarding of incoming IPv6 packets
@@ -308,21 +305,10 @@ Generic options:
This setting has been moved into net.ipv4.ip_forward setting
in /etc/sysctl.conf. Setting it to 1 there enables IP forwarding,
setting it to 0 disables it (which is the default for RFC compliance).
-<<<<<<< HEAD
- Note these options can still be used for compatibility, but you
- really have to swith to /etc/sysctl.conf facilities.
- DEFRAG_IPV4=yes|no
- Setting this to yes used to automatically defragment IPv4
- packets. This is a good idea for masquerading, and
- a bad idea otherwise. This setting was moved into
- net.ipv4.ip_always_defrag setting in /etc/sysctl.conf. It
- is no longer valid for 2.4 kernels.
-=======
NETWORKWAIT=yes|no
This is not used with the move to systemd.
->>>>>>> initscripts-9.41-1
NETWORKING_IPV6=yes|no
To do this properly, disable IPv6 in the module itself.
This can be done by booting the kernel with "ipv6.disable_ipv6=1".
@@ -574,14 +560,10 @@ Files in /etc/sysconfig/network-scripts/
ONBOOT=yes|no (not valid for alias devices; use ONPARENT)
HOTPLUG=yes|no
USERCTL=yes|no
-<<<<<<< HEAD
- BOOTPROTO=none|bootp|dhcp|static
-=======
BOOTPROTO=none|bootp|dhcp
'bootp' or 'dhcp' cause a DHCP client to run on the device. Any other
value causes any static configuration in the file to be applied.
VLAN=yes|no
->>>>>>> initscripts-9.41-1
MTU=
Default MTU for this device
WINDOW=
@@ -644,18 +626,16 @@ Files in /etc/sysconfig/network-scripts/
If not set, default zone (specified in /etc/firewalld/firewalld.conf)
is used. To see all available zones, run 'firewall-cmd --get-zones'.
-<<<<<<< HEAD
- If BOOTPROTO is not "none", then the only other item that
- must be set is the DEVICE item; all the rest will be determined
- by the boot protocol. No "dummy" entries need to be created.
-
+ For dynamic addressing (BOOTPROTO=dhcp) only DEVICE needs to
+ be set; all the rest will be determined by the boot protocol.
+
You can specify which dhcp client to use with the DHCP_CLIENT, if
the DHCP_CLIENT is not specified we trying to launch in order :
/sbin/dhclient
/sbin/dhcpcd
/sbin/pump
/sbin/dhcpxd
- if you have a preferred client define the DHCP_CLIENT variable.
+ if you have a preferred client define the DHCP_CLIENT variable.
When you use dhclient (which it is the default on a Mandrake-Linux
system) you can specify a timeout of waiting the answer from server,
the option is called DHCP_TIMEOUT the default is 60 sec.
@@ -693,11 +673,6 @@ Files in /etc/sysconfig/network-scripts/
CRDA_DOMAIN=<domain>
Wireless regulatory domain for this connection (man 8 crda).
-=======
- For dynamic addressing (BOOTPROTO=dhcp) only DEVICE needs to
- be set; all the rest will be determined by the boot protocol.
->>>>>>> initscripts-9.41-1
-
Base items being deprecated:
NETWORK=<will be calculated automatically with ipcalc>
BROADCAST=<will be calculated automatically with ipcalc>
@@ -839,7 +814,7 @@ Files in /etc/sysconfig/network-scripts/
Ethernet 802.1q VLAN items:
DEVICE=eth0.42
Initscripts use DEV_PLUS_VID_NO_PAD naming mode for VLAN
- devices.
+ devices.
Example: eth0.42 for vlan 42 on device eth0.
Valid VLAN ID range is 0-4095. Most ethernet switches reserve
VLAN ID 1 to be used as management VLAN; starting from VLAN